: progress report(not a good one either)


FULLSIZE
03-21-2003, 11:20 PM
i'm tryin to get the motor(360) in my truck fired up and it just wont do it. it cranks over just fine, timing is good, sounds farily even when cranking so i figure i'm good to go with the compression issue. i get kinda puzzled so i pull all the plugs for a compression test and i find:
#1 = 110
#3 = 90
#5 = 60
#7 = 60

#2 = 90
#4 = 90
#6 = 70
#8 = 60

4 cylinders have half the compression my old 360 in my jeep did. i noticed that the 4 rearmost cylinders have the lowest compression, any ideas before i rip my cuda motor out and install it in the truck(with a smaller cam of course)?:rolleyes:

GRMhick
03-21-2003, 11:23 PM
your going to put a 408 in the cuda first, right?

Garrett

FULLSIZE
03-22-2003, 12:31 AM
i think the 360 comin out of the dodge will be the donor for the 408.;)

GRMhick
03-22-2003, 05:18 AM
gotcha :flipoff2:

Garrett

Lloyd
03-22-2003, 08:01 AM
Try a good squirt of engine oil (like half a teaspoon) in each cylinder, then re-run your compression test. If it's much better it's rings, if not then valves - but at minimum you're looking at pulling the heads to fix it. Also, if you can run your compression tester in a leakdown mode, it's possible to diagnose a scored cylinder wall by slowly rotating backwards through the compression stroke. Sorry to hear this. :(

FULLSIZE
03-22-2003, 09:59 AM
my problem is the truck needs to move soon, the cuda(chassis wise) is not up to par(or is that mopar) and i have no money to put into the engine thats in the truck right now. the cuda is comin apart this summer anyways to start fiddling with it so this seems like the wise option at this point.:(

thanks for the tips Llyod, i'll keep those in mind.;)

SeaBass44
03-22-2003, 04:38 PM
like he said, do a comp test wet now, and if above 15-20 psi improvement, it's rings, less then that, it's valves, if only a 5-10psi improvement, it's normal

GRMhick
03-22-2003, 08:14 PM
Half off sale at pick and pull.. may be another option right there.

Garrett

FULLSIZE
03-22-2003, 10:48 PM
ya, i know, but the cuda motor runs good and i know where its been.;)

FULLSIZE
03-25-2003, 09:10 PM
heres a pic of the donor motor:

FULLSIZE
03-25-2003, 09:11 PM
it ran low 13's at sac raceway in the cuda with lots of wheelspin into 3rd gear;)

sounds like a crawler motor to me.:flipoff2:

Big Mo
03-25-2003, 09:19 PM
Well damn I hate to see the motor come outta the sweet little Cuda but if it must happen then it must...:(

Two Dogs F..king
03-29-2003, 10:50 PM
I vote NO on Proposition 408:D

FULLSIZE
03-30-2003, 10:25 PM
Originally posted by Aquaman
I vote NO on Proposition 408:D

all in favor say I..............

I

sorry, your out voted!:flipoff2:

Amanda G
04-01-2003, 06:09 PM
heh, Big Mo thinks your Cuda's pretty... :laughing:

Brian dude, pull the Cuda motor. DO IT!! DOOOOOOOOO IIIIIIIIIIIT!! :D
I wanna see yer ass on the trail!!

FULLSIZE
04-01-2003, 10:00 PM
rumpity rump, rumpity rump goes the power wagon down the trail soon..............:D