We are now stocking ARP studs, nuts, and washers to fit your Kingpin high steer arms.

* 220,000 psi tensile strength
* .930 shank to fit 1"-1.5" thick arms
* ARP high strength nuts and washers included

D60115K- 5 stud high steer kit $35.00 (5th stud is for the Dedenbear Knuckle)
D60114K- 4 stud high steer kit $29.00

Available Now!

I need a 4 stud kit, can this be done online with paypal?

We are not set up for online orders, you can give me a call tomorrow or give me your number and I can call you. We can ship them C.O.D. or Credit Card.

Ryan

Uh, I hate to beg.......I mean ask, but want about an 8 stud kit? anyway can you give a good deal on those? I mean, why not do both sides at once.

Originally posted by BustedRig
Uh, I hate to beg.......I mean ask, but want about an 8 stud kit? anyway can you give a good deal on those? I mean, why not do both sides at once.

We have already priced them as low as we can go, but it never hurts to ask.

Ryan

pic of studs installled

Can you get them with tapered washers?

Originally posted by SittonHigh
Can you get them with tapered washers?

No tapered washers. Most people use the stamped steel kingpin cap in conjunction with high steer arms. The steel cap has no provisions for a tapered seat allowing the use of tapered washers or nuts. If you were to taper the holes in the high steer arm, you could no longer run a kingpin cap. I suppose if you wanted to run a factory cast kingpin cap that has the tapers in it on top of the high steer arm, you could run tapered washers. The studs however would need to be longer than what we are offering.
With a properly made high steer arm (holes in the correct locations and correct diameter) the studs fit great and the steering arms do not move at all.

Doug

Do you sell the studs without the bolts and washers?

Originally posted by Eric
Do you sell the studs without the bolts and washers?

No, but I can sell you a single stud, nut, and washer for $9

Ryan

http://www.offroaddesign.com/D60HiSteerarms.JPG

How about a tapered nut or a tapered washer?
Fine thread on both ends? maybe? Then you could use a wide selection of nuts.

Tapered nuts would work great with your arms but I do not carry them or have a source for them

Ryan

D60003K- 5 stud high steer kit $35.00 (5th stud is for the Dedenbear Super Knuckle)

Super Knuckle - that's an original name.:D

Sorry Tony, after I posted it I saw that you offer a super knuckle. I threw that in there because we use it with some of our other products like our Superglide (http://www.dedenbear.com/tranny_cat.htm) and our Delay Boxes (http://www.dedenbear.com/dlybx_cat.htm) It looks like we have already droped it as a knuckle description.

Ryan

Call them what ever you want. I was just being funny.......

;)

Ryan and Tony...I guess this means that you guys are both SUPER...





























:rainbow:


:flipoff2:

I knew you'd be along soon enough, Dustin.

I don't think anyone ever trade marked the word " super " but it was fun to tease Ryan.

tony k

Its been a while, but back to the top. Keep the orders comming on these, the demand has been great.

Ryan :usa:

Bump :usa:

TTT :usa:

Keep the orders comming!

TOP

TOP

Bump

Top

I'm surprised no one has asked already... what is the shank diameter? Same as oem shank diameter??

I am surprised also, but they are ground to .500


Ryan

Keep the orders comming!


Thanks!

My OE Stud is 0.5275" for a FYI. Thje ARP's will be strong as OE (probably better even), but you just lose the fine thread on the one side, just make sit a little harder to find a tapered nut that works.

Still beats the crap out of paying what The dealerships want for the "real" deal.

Ttt

Bump!