So how many of you have installed your chistmas presents yet? My crawler box is still sitting on my workbench. How about the beadlocks and spools Camo? Anyone else get some goodies for Christmas installed?

no parts for my truck:(
santa knows when people can buy there own stuff.

hy steer kit.........still on the workbench.

its getting there half welded up

http://community.webshots.com/storage/1/v0/9/81/50/28798150lGyHENRAQA_ph.jpg

my list is looking like this:
Replace both broken birfields
Replace bent tie rod
Install crawler box
Rework drive lines
Install wide rear axle
Install york compressor (collecting dust for too long)
Install front axle shims- need better pinion angle

Maybe i'll be done by next christmas..

ya, i wore my GAWD DAMNED fleece home.... :mad3:

the millermatic 210 is on backorder :flipoff2:

Yep, cage is in. Speaker pods turned out awesome, now I just need buckets and 5 points

I mounted one just for shits and giggles. I'm repainting the rings black, but I wanted to get an actual height.
http://home.kc.rr.com/toyota4x4s/images/SAS/Beadlocks/Eaton_SX.JPG
I'm also getting a crawler box this weekend. Little late, but I'll take it. :D

Rims and tires are mounted on the truck and the one piece rear d-shaft is on it's way. Just have to figure out how to get the heater motor to work and I can get it out and play in the snow.

bead locks are on and the tera 60 are in the garage being built as we speak

the new crawler is in and the drivelines are being built as we speak.:D

My PIAA40 are still sitting on my desk waitting for me to finish my bumper.

No one got me anything kewl, so i had to get my own X-mass/new-years present/s....
Rear shock mounts...Done
Redoing the buggys...in progress
Motor Rebuild kit...still thinking about
onboard-air...on the bench :D
5:29's....on the way :D
Spool.....on the way :D
detroit...on the way :D
Just ordered a merlin yesterday... :D :D
I'm thinking about pulling everything at once-motor, tranny/T-case, both axles...just for pictures... needs to be done anyway...

brand new CB still sitting in the kitchen, waiting for me to buy an antenna....

hehe...got lots to install. rear bumper,
5.29's front and rear,
spool for the back
lockright for the front
hilift to mount (once I figure out the best place)
rollbar lights to hook up
front shackles to install
yadda yadda :cool:

hey-

the LC Engineering Header is on and AWESOME!!!!

later

Originally posted by Polar
its getting there half welded up

http://community.webshots.com/storage/1/v0/9/81/50/28798150lGyHENRAQA_ph.jpg


DAMM!!! that thing is ugly !!!- And I thought mine was like a junker.

How lift is there on it??

Hi steer is going on in two weeks. Crawler box is still on the bench. Will be until I have a free weekend, like in March (?)

The "MALE CRISIS CENTER" sign that my wife had made for the shop will be going up in a couple of weeks... :)

Originally posted by rockota
The "MALE CRISIS CENTER" sign that my wife had made for the shop will be going up in a couple of weeks... :)

That's a good one! :D

Originally posted by dangerber


That's a good one! :D

Yeah... The word "CRISIS" is in Blood Red letters.. :) She also had coveralls made with that slogan ironed on the back... can't say she doesn't have a sense of humor.

I'll post a pic when I get the sign hung up in the shop.. :D

Rebuilt motor is in and rockin'.:D
Optima is still sitting on workbench. Putting it in tonite.

Lockright and front knuckle rebuild kit that my parents got me and the spool that i bought myself were installed last week.

It sure is nice being locked front and rear.

Originally posted by 85toyboy
Anyone else get some goodies for Christmas installed?

Snipped by steveh !!! Not funny, take this kind of crap to chit chat. Think before you post!

<img src="http://community.webshots.com/storage/1/v0/9/81/50/28798150lGyHENRAQA_ph.jpg" width="480" height="320">
Bob the back end, sand everything down mostly smooth, prime it and paint it, and you'll be lookin 1,000% better...

That's what I did to mine. You can hardly tell the passengers side was dented up so bad the door wouldn't open with the new (flat) paint:
<img src="http://www.people.memphis.edu/~ecmills/paint/toy04.jpg">

Didn't get any actual truck parts, but i got some clamps and stuff that I used to make my flatbed while I'm off from school. Still finishing up a few little things (needs recovery points, a hitch maybe, and back up lights, i've been driving it around for a while though). I'll post some pics soon.

Got a new mag base antenea, but now my CB don't work. Guess it's time for one of those new fangled 40 ch models for the birthday. Got mama a new union suit.... I like that flap door :rasta:

Hi- Steer is on, Budbuilt crossmember is on, Marlin 4.7:1 install kit ordered.

she looks rough but im not going for the show and shine just functional. the lift is all pro 5.5

http://community.webshots.com/storage/1/v4/7/43/92/28874392OchnNwLhYy_ph.jpg

i just picked up the truck other mods comming including the bumper...........:p

Originally posted by rockota
The "MALE CRISIS CENTER" sign that my wife had made for the shop will be going up in a couple of weeks... :)


Hahahahahaha Ohh that is good!

Does the sign not get to go up until the new shop is finished then?

Santa got that speed hole in my frame all fixed up!

Originally posted by Satan's_Minion



Hahahahahaha Ohh that is good!

Does the sign not get to go up until the new shop is finished then?

Santa got that speed hole in my frame all fixed up!

Yup - not until the shop is done. Tape and Mud left... Then paint, benches and toools!

BTW - why don't you just build yerself a whole new frame - it'd be faster ...

Originally posted by rockota


BTW - why don't you just build yerself a whole new frame - it'd be faster ...


Wait I have an idea, why don't you build me a new frame in that fancy shop of yours. Yeah I like that idea