Any help is appricated. I need one left hand thread and one right hand thread.

A = 3"
B = 5/16"
C = 5/8"
D = 11/16"

Any help on this would be appricated. I have no idea what these came off of in the first place.

http://www.partsamerica.com/product_images/AAP/TRW/TieRodEndsType1.jpg

TINY!

Threads per inch...?

any other suggestion other then tiny? :rolleyes:

it has dana 44 knuckles and all I need is some sort of setup for my draglink. I just have no idea what to tell the part store guys for rod ends.

Hook me up!:flipoff2:

Originally posted by Pig Penn
Threads per inch...?

thats what I meant by 5/16. guess that only makes sense to me. it has 18 threads per inch. and is 5/8 wide

Originally posted by Erik D


thats what I meant by 5/16. guess that only makes sense to me. it has 18 threads per inch. and is 5/8 wide

I'm glad it made sense to somebody! :flipoff2:


The only 5/8-18 TRE I know of is
Moog ES2053R & ES2053L

even if somebody can just give me info on the right taper I will have a new drag link made
:beer:

If your having a new link made why stick with such a small TRE. The Moog ES150 is 3/4-16 and has the taper your looking for. The Moog #'s I posted above have the right taper and the wimpy 5/8. The Moog ES 150 have the right taper and a beefy 3/4. Spydertrax has links made to your spec with 3/4-16 ends and DOM tubing for ~80.00. The ES150 ends are 14.15ea from stockcarproducts.com

Small end 5/8 or .625

Fat end 11/16 or .68750

thats what I used on my toy worked out good. Broke 2 steering arm studs but never harmed the tie rods

finally going to fix your rig?
I have broken 3 more birfields since last time we went wheeling
I just ordered a rc 44 for my toy

give me a call we should go out to tsf

Originally posted by homegrowntoy
finally going to fix your rig?
I have broken 3 more birfields since last time we went wheeling
I just ordered a rc 44 for my toy

give me a call we should go out to tsf

Yeah I have been lazy/busy/broke. We didnt see it when I broke but I also broke the two front studs from my steering arm. That was an exciting and long drive home. It took me awhile to get around to extracting those studs out of the knuckle. Did you break the birfs because of your "welded dif"?

Thanks old scout! I will give it a shot.

Es150 should be ok.....If I was gonna do it I would "upgrade" to the 7/8 tie-rod ends for the "heavy duty" factor.....about the same cost really........IMO.......:D :beer:

Originally posted by Shaker
Es150 should be ok.....If I was gonna do it I would "upgrade" to the 7/8 tie-rod ends for the "heavy duty" factor.....about the same cost really........IMO.......:D :beer:

The 3/4 doesn't have all the PITA problems with finding $$ LH taps.

Were are you getting the 7/8 TREs for 15.00????

Sheit he was going to use 5/8 and 3/4 is a huge improvment. :bounce: :bounce2: :bounce:

Originally posted by Old Scout


The 3/4 doesn't have all the PITA problems with finding $$ LH taps.

Were are you getting the 7/8 TREs for 15.00????

Sheit he was going to use 5/8 and 3/4 is a huge improvment. :bounce: :bounce2: :bounce:

No pain I have them ALL in my shop...:D As for the price only 7.00 more (each).... subtract that from the 80.00 "rod" and get a "rockstomper" tierod or hell I'll make him 1.....:D :beer: :beer:

I was planning on getting a rockstomper link anywho. Do you have a part # for the 7/8 TRE? BTW anybody know where I can get a steering block/spacer for the steering arm? I need 1" and all I can find on the net is 3":confused:

You will need to ream if you go 7/8"! There are no TREs with the taper you wanted above that are 7/8'.

Originally posted by Erik D
I was planning on getting a rockstomper link anywho. Do you have a part # for the 7/8 TRE? BTW anybody know where I can get a steering block/spacer for the steering arm? I need 1" and all I can find on the net is 3":confused:

Part #'s

ES 2010L
ES 2234R
ES 2027L
ES 2026R

As for the Block I usually cut/machine one.. :beer: :D