I have a few Ford 60's for sale. Will ship at buyers expense. Here is what I have...

85-91.5 Ford front HP60, kingpin knuckle, 3.54 gears, complete from lockout to lockout. Rotors have plenty of meat left, just need to be turned. Calipers are there, for cores, will need to be replaced. Already on a pallet and ready to ship. $1100 PRICE REDUCTION, Will sell for $1000

Set of 60's from a running 78 F250. HP front, standard rear, kingpin knuckle, not sure on ratio, not sure on brake condition, but complete from lockout to lockout including brakes. $1200 PRICE REDUCTION, Will sell for $1100

OR...PACKAGE DEAL: 2 fronts, 1 rear, $2000:)

Sorry, no pics. You guys know what they look like :flipoff2:

PM or email me at jrh713@yahoo.com if interested.


PRICE REDUCTION, Need to sell soon!

BTT, Lower Prices!

Located in Massachusetts

Btt

Might be interested, but I need to see what I am buying. email me go2camp@comcast.net

I will work on the pics. If I can get home by this weekend I will have pics then.

Maybe this will help in the mean time....I need to know if the following are in usable/good condition:

Front:
All brake parts
Hubs
King Pins...sloppy or tight
Shafts
Housing/tubs straight/not cracked

I don't care about diff/gears, spring/shock mounts, or ujoints...these will get replaced or moved anyway. Unless it has a locker already

Rear:

All brake parts including
Housing/tubs...straight, no cracks...surface rust okay
Shafts

I don't care about diff or gears or spring/shock mounts...unless it has a locker already

Marlon

I can tell you from my experience with J. Hard that his work and word is good. Just picked up a set of 60's from him and not only was the prices right, but he told me if anything didn't hold up as expected to make sure he was the first to know(did a bit of work for me on them). Real stand up guy. Looking forward to working with him again.

Maybe this will help in the mean time....I need to know if the following are in usable/good condition:

Front:
All brake parts
Hubs
King Pins...sloppy or tight
Shafts
Housing/tubs straight/not cracked

I don't care about diff/gears, spring/shock mounts, or ujoints...these will get replaced or moved anyway. Unless it has a locker already

Rear:

All brake parts including
Housing/tubs...straight, no cracks...surface rust okay
Shafts

I don't care about diff or gears or spring/shock mounts...unless it has a locker already

Marlon

Chad, thanks for the kind words. Hope the swap goes well for you. Send some pics.:)

Marlon,

The condition of each axle is as follows...

85-91.5 Front HP60:
Brakes- Rotors are rusty but have plenty of meat and could be turned, Calipers are there, just not attached to the axle, IMO they should be replaced. The hardware piece that you need to attachthe caliper to the caliper bracket is missing but comes with the calipers when buying them. Use the old calipers for cores. (Dual Piston Ford Calipers).
Hubs- Move freely and lock/unlock properly.
Kingpins- Are tight.
Shafts- Solid, no problems. As usual, 35 spline inners and 30 spline outers.
Housing- Straight, no cracks, obviously some surface rust. All factory brakets are still on.
Sitting on a pallet and ready to ship if needed.

78-79 Front HP60/Standard Rear 60
Brakes- Not sure on brake condition as the axle is still in a running truck. (Engine problems I believe) Brakes will be complete and POSSIBLY usable, as is. I will know more when I pull the axle next week. (Dual Piston Ford Calipers in front Drums in rear).
Hubs- Move freely and lock/unlock properly.
Kingpins, Shafts, Housings,- Look to be fine and usable, as is. I will know definitevely once I pull them out of the truck next week.

Joe

just pm'd you.

Thanks Joe...If you have more info after pulling the axles, PM me or email me go2camp@comcast.net

Btt

where are these located in mass?

Located in North Attleboro, MA.

btt

:rolleyes: Btt

I will be able to find out the gear ratio on the f/r set on Monday. Somebody has got to need these axles.

btt

I am still interested...Still available? What would price be shipped to 95630? Pics? Just front axle or both...?