|
mudhog 01-28-2002, 11:45 AM hey all i need some info i have a 77 blazer with a half ton dana 44 i just got a 75 dodge dana 60 front for it what i need to know is will my brake lines bolt up to the dana 60 or do i need new ones? thanks in advance:) mudtruck44 01-29-2002, 08:06 AM There is a good change that they will work. The calipers are pretty much the same I think but Chevy did use two different size banjo bolts for their brake lines but I can not remember what year has which size. mudhog 01-29-2002, 10:14 AM thank you for the info:) Derf00 01-29-2002, 11:24 AM I recently did this swap with a D60 out of a CUCV and the calipers were Bendix and the banjo bolts matched the calipers on the 10B on my '90 Jimmy. BlazzinOR 01-30-2002, 07:06 PM Originally posted by mudhog thank you for the info:) BOUT TIME YOU GOT OVER HERE NEWBIE :flipoff2: You might bolt directly on, or might have to open up the hole a bit. Can you eyeball it and scope it out? I opened up the hole in my stainless lines with a drill bit - no problems. One other thing, you might have to grind/round off the banjo fitting, Stephen W actually clued me in on that one. One tons rule.............. mudhog 01-30-2002, 08:11 PM well i need to go somewhere to ask questions while ck5 is down:( i have looked at mine vs the dodge and i think i will need to gring it down can you give me more info on that? i will be out at danials putting his lift on tomorrow during the day but will be home in the evening say after 6pm give me a call i am not a newbie:mad2: :flipoff2: lol and one ton's do rull:D :D :D :D BlueBeast 01-30-2002, 08:36 PM shannon, quit screwin around and get that thing in there!:p i'm jonesin for k5 too.:mad: Wayne 89 1 Ton K5 01-30-2002, 10:36 PM Well I guess all the CK5's found a place to play untill Steve gets the site back up. Wayne 89 1 Ton K5 01-30-2002, 10:49 PM In answering your ?, no they are not a direct bolt in. The D44 is an oddball. You can make them work or buy new lines. If you deside on new lines just get a set for a 10 bolt and they should fit. As far as I know Dodge and GM used the same fitting on the caliper and if you want to double check just go to the parts store and compare the 2. powermad 01-31-2002, 03:42 AM Shannon I have a line on a few trails nearby, up in the Scappoose area. I might have found one up here by my house. I went part way up and if it wasn't 3am I might have gone all the way. But it was fun for a moment. LOL Lets get that bad boy in and hit some trails. :D mudhog 01-31-2002, 05:40 AM i will have it in saturday:) thanks for the info wayne:) californiak5 01-31-2002, 06:52 AM Well I guess all the CK5's found a place to play untill Steve gets the site back up. Everyone except for Wes that is. :eek: See Ya, Keith BlazzinOR 01-31-2002, 07:31 PM Originally posted by mudhog well i need to go somewhere to ask questions while ck5 is down:( i have looked at mine vs the dodge and i think i will need to gring it down can you give me more info on that? i will be out at danials putting his lift on tomorrow during the day but will be home in the evening say after 6pm give me a call i am not a newbie:mad2: :flipoff2: lol and one ton's do rull:D :D :D :D You are too a newbie...............just look under your name :flipoff2: I'm in Philly right now, don't get home till Friday afternoon.............I'll give ya a call on Sat. mudhog 02-01-2002, 08:53 AM i will be at my dads saturday morning around 10am so give me a call friday night or early saturday morning:) shannon (hopfully a full member of the one ton club by saturday night) | |