Dont flame me yet. Ive searched and seen all the tube fenders everyone builds with no inner fender. Has anyone out there built actually strong flat fenders and kept the existing inner fender in some form? I am not ready to drop the inner fender yet.

Take a look at Poison Spyder Customs.

Yea somebody does but can't remember who..they are an overlay of your existing fenders after you cut the crap out of them, but you can keep the inners in place...like you will hear SEARCH

www.metalfusionfab.com

Best tube fenders I've seen and they retain the stock inner fenders. They are plenty stout too.

found it..I'm just an old man and don't know how you-all copy an post these http's and links but bear with me ...google search fourwheeler.com and lok for "project teal-J II part VII I mostly just get on here to look at jeeps and parts, not "talkin"

Well I don't know if you want "Just the Look" or a tube fender to stand up to rocks....... Overlay one are not as strong as the full tube fender.... I have some from TnT customs and they kicka$$... Strong as hell....and they come with a 3/4 fender well.......

www.tntcustoms.com

http://www.colorado4x4.org/vbb/showthread.php?t=15898


http://www.rock-nutz.com/php/album_picm.php?pic_id=72

This (http://www.pirate4x4.com/forum/showthread.php?t=240571&highlight=fender) is what I built for Bob ...

Poison spider's don't use the stock inner fender but they use 3/16 steel which is better imho. I can stand on mine and i'm a fat sonsabitch.

www.metalfusionfab.com

Best tube fenders I've seen and they retain the stock inner fenders. They are plenty stout too.

I put those in my TJ about a month ago. Very stoud. I kneel on them all the time when working in the engine compartment. I like that you can remove the panels for better access to the engine bay.

i built mine and kept the inner fender. ill post pix tomarrow when i can take them in the light. used 1 1/2 tube with 1/8 plate top and bottom. have some pics on my webshots

Well I don't know if you want "Just the Look" or a tube fender to stand up to rocks....... Overlay one are not as strong as the full tube fender.... I have some from TnT customs and they kicka$$... Strong as hell....and they come with a 3/4 fender well.......

www.tntcustoms.com

http://www.colorado4x4.org/vbb/showthread.php?t=15898


http://www.rock-nutz.com/php/album_picm.php?pic_id=72
Are those Poison Spyder corners or home made job?

they're tnt customs. Can you not read? He only mentioned it about 5 times.

I did. Here are a few pics. Very strong, great clearance. It works great. Dave
http://frontiernet.net/~selph/tubea013.jpg http://frontiernet.net/~selph/tubea014.jpg http://frontiernet.net/~selph/tubea024.jpg

Obviously you CANT fawkin read. Im talking about the REAR competition cut corners. Not the tube fenders you fawkin newbie.

No where in his post does he say "My rear comp. corners are TNT customs"


ASSHAT.

can we get more pics of the were that's tied in selph?

It is all TnT Customs.... Tube fenderZ, SliderZ, CornerZ.... Check the web page out.....You should find everything you need....

I did. Here are a few pics. Very strong, great clearance. It works great. Dave

And how much does that weigh?

It weighs about 60lbs. It's tied in to myrock sliders and the frony frame. The engine bay tube goes all the way across. It's made from 1.75" X .120 wall HREW. Thanks, Dave

It is all TnT Customs.... Tube fenderZ, SliderZ, CornerZ.... Check the web page out.....You should find everything you need....

That sucks that the full corners are on site installed only items.

On mine, I kept most of the stock fender and just added on over the top and incorperated the flare in at the same time. I tied it to the front grill hoop and the rock sliders and it is strong enough to move the Jeep sideways with it.

That sucks that the full corners are on site installed only items.

I'm would bet if you talk to him he would sell them for install by you.... Give Bob a call.. or E-mail..... He has just started and might not have all the templates yet... and that might be why??

fender

.

,

:shaking: Hell, I went the PO-BOY BUILT (bootie fab) :smokin:

Cutt the stock fender, tied in a front stinger to the rock sliders !!
Works for me !!

http://www.usjeeps.com/members/p155-1100117145.jpg

JEEPSKEET: Hell, I went the PO-BOY BUILT (bootie fab)



mine were cheap to make tube and 1/8 plate. wasnt hard to do im going to put them on my cj when i start one.

i have some pics of my tubefenders if anyone would like to post them up.

If you could build the outside, you could do the inside too.
http://www.crawltech.com/albums/Rigs-and-Misc/Fender_armor_inside.jpg

I have some that I built using the stock inner fender, I can take some pictures if someone will host them.

I have some that I built using the stock inner fender, I can take some pictures if someone will host them.



k

k


You have mail.

these are DWEST fenders

Here's mine built by http://www.roarkfabworks.com

In one month that they have been on, they have been on trees, and bashed into rocks severely at Paragon.

http://www.pixhost.com/pixy/yjdude/a3.jpg

these are DWEST fenders
do you have to get FAA clearances before you drive that thing? Looks like it has enough wingspan to fly...

http://www.pirate4x4.com/forum/attachment.php?attachmentid=157903

do you have to get FAA clearances before you drive that thing? Looks like it has enough wingspan to fly...

http://www.pirate4x4.com/forum/attachment.php?attachmentid=157903



ask dwest not me! i just posted the pics for him because i have a red star :flipoff2:

mine

If your making them then just take your current inner fender and cut along the ridge just inside the hood line. then cut to fit.

http://wheelingpiazzas.com/pictures/fenders/DCP01056.JPG