These are the jig bushings you need to shorten axles,,, I now make sizes for Dana 30, Dana 44, Dana 60, Ford 9" small bearing ,Ford 9" large bearing, Ford 8.8 , Corp 10 bolt , 12 bolt, 14 bolt and stock them. Other sizes not in stock well take about 3 or 4 days to ship.

A set of Bushings for the Differential run $99 a set including shipping

wheel bearing bushing for semi float or full float axles run $55 each including shipping

1 1/4" by 48" heat treated ground and polished bars run $120 including shipping.


( on the diff bushings one size will fit D44/60 and 14 bolt and the other size fits Ford 9" small & large,D30, and corp 10 & 12 bolt )

Duffy
D.D.Machine
(360)779-2500 shop #
(360)649-4465 cell #

The bar seems short for 48"??
lke if you were to make a 63" ford 9" would not the tool need to be 60" plus the leinght of the alinement tools for the ends of the housing, or am i missing smothing ??
R/T

The bar seems short for 48"??
lke if you were to make a 63" ford 9" would not the tool need to be 60" plus the leinght of the alinement tools for the ends of the housing, or am i missing smothing ??
R/T
Your missing something
These are the jig bushings you need to shorten axles,,,,

I'm intersted in buying a bar and some bushings but I also question the 48" length. Is that a typo or ????

Otherwise I would like a quote on a bar, Dana44/60 bushings, need end bushings for both Set10 and set20 bearing ends shipped to 95650 business address.

Thanks, Jeff
________
Glass Bubblers (http://bubblers.net/)

You do one side at a time then move the bar to the other side ,,,, In 23 years or axle shorting I have never found the 48" bar to short yet.

Duffy
P.S. you only need about 40" of bar to do a full width 14bolt

Ihojeff I got the set 10 in stock but well have to make up the set 20 size but it well only be a few days turn around time..
Your looking at
diff bushings $99
2 wheel bushings $110
48" bar $120
so with shipping it comes to $329
( all my products have a set shipping cost)

Thanks Duffy
D.D.Machine
(360)779-2500 shop
(360)649-4465 Cell

My paypal name is dd98370@hotmail.com

ford 9" sm/bg bearing and D30 set.

Ihojeff I got the set 10 in stock but well have to make up the set 20 size but it well only be a few days turn around time..
Your looking at
diff bushings $99
2 wheel bushings $110
48" bar $120
so with shipping it comes to $329
( all my products have a set shipping cost)

Thanks Duffy
D.D.Machine
(360)779-2500 shop
(360)649-4465 Cell

My paypal name is dd98370@hotmail.com

Makes sense now that you explained it. Came from a diffy shop that did both sides at once. I'll have the coin next week and will paypal you then.

Thanks, Jeff
________
ChicagoFan cam (http://camslivesexy.com/cam/ChicagoFan)

I get it know I was thinking like jeff was, what would be the price for the full set and shipping to oregon 97411.
I take it from jeffs coment you take PayPal

richard
What do you mean by a full set ? for what axle?

For a axle you well need a set of diff bushing ($99 with shipping) and a wheel bearing bushing ($55 with shipping ) and a bar ($120 with shipping)
so your looking at the same as jeff at $329 for a set to your door.

Thanks Duffy

( I have used a 72" bar at a friends shop in the past and it sucked,,,, I like to feal the drag on the bar when I weld it and with it going all the way thrue you get a reading thats hard to tell if its the side your working on or if the other side thats draging )

Thanks Duffy

What I was thinking was all that was listed above.

Richard The two sets of diff bushings well cover all of the axles listed,, but you need bushing for the wheel bearing or full float spindle to ....
and there is about 8 to 12 sizes needed for a fairly complete set or wheel bushings.

If your going to be working on dana axles and ford axles your best bet is to buy both sets of diff bushings and buy the wheel bearing bushings as you need them ,,,

Thats how I`m doing my stock for now on wheel bushings ,,,, I well stock set 10 , set 20 and ford big and small and one size of full float bushings ,,, but tell I start selling a lot of one size there is no point in stocking them ,,,, I have made a bunch of blanks with the right ID and well turn the OD to fill the orders.

Duffy

I'm looking to build a Dana 60 rear using a Rock Crusher center and the Warn 35 spline full float kit. Do you have the outer bushings for the Warn kit?

I don`t now what the dia of the outer bearing is on the Warn kits,,, If you mail me the spindle it would only take me 2 or 3 days to make what ever size your need ,,,,, Your looking at about $75 + shipping


The D60 chunk bushing I keep in stock all the time... The only spindle bushings I make for stock are set 10 and set 20 (ford big) for the rest I got blanks made up so I only need to turn the OD to size

Duffy

The warn FF kit uses the same size bearings as a front 60, but the spacing is closer together on the spindle. You will either need a custom spindle to weld to the tube, or the correct axle end to fit whatever spindle you have, and the bushing to fit that end


Does your full float bushing slide over the spindle, or thread onto the spindle?? Can you make one with a 1.5" bore?

I think that the outer spindle mount has the same ID as some Ford applications. I measured the ID and came up with 3.15". Is that the same or close to big or small bearing ford? I included a picture of the end to make things more clear. The spindle is seperate and bolts onto these ends much like a front application.

Hey that's the same as the ends on a D60 housing I bought for $35 on eBay. Where'd ya get that? I had a set of Ford front D60 spindles machined to fit these ends - are you saying somebody (Warn?) makes spindles specifically to mount on these? What's the bolt circle diameter?

I have made them to slide on and to thread on ..... I like the slide on better my self .... and yes I can make 1.500 bore ones.

Duffy

I think that the outer spindle mount has the same ID as some Ford applications. I measured the ID and came up with 3.15". Is that the same or close to big or small bearing ford? I included a picture of the end to make things more clear. The spindle is seperate and bolts onto these ends much like a front application.

BTW, to answer your question, that is the same as the Ford big bearing set up, so you'd just use the Ford wheel bearing bushing.

I keep the set 20(ford big) bearing puck on the shelf, There the best selling puck.

Duffy

It'd be cool to see some pics of your products in use.

when are the toyota 8" ones comin?

j

ETA on a Dana 70 diff

And how do the FF pucks work on the axle ends?

toyata 8" when ever someone needs one ,,, easy to make up a set

some D70 used the same chunk bearings as the D60`s I make now.
If your talking D70 HD I can make them up.

toyata 8" when ever someone needs one ,,, easy to make up a set

cool, I could use some... I am gonna be doing some welding/trussing on my 8" axles and would prefer that they didn't warp to much. cost shipped to 98686?

j

it well not stop it from warping ,,, you well have to play with how your welding it to keep the warping down ,, but it well let you feal whats going on.
Let me look thrue my junk and see If I got some 8" chunk bearings for size

Duffy

are you still selling these jigs?

Did you get your batch of full float end pucks done??
________
a0LatinAss live (http://camslivesexy.com/cam/a0LatinAss)

Jeff your on the list for them ,,, I got them cut off and ready for the cnc ,, just need to find a day to run them ,

I`m good in stock on all other set up parts,

Duffy

Hey Duffy do you install axle ends yourself, as well, or can you recommend someone close to Monroe who can do it? Thanks!

How much for everything to shorten a 9"?

Paypal sent - Thanks!

Full set up for a 9" with your choice of large or small wheel end puck well run $269+$30 for shipping

same price for D44/D60 kit for simi float ends.

Response to 9" set up. What determines large or small pucks? Can you make a jig for MOG/9" hybrids? If so, how much?

Hello are you taking credit card now I thought I seen some of your tooling on Ebay.
andersonr@orregonfcu.com

At this time I`m doing no custom work. I have to mutch on my plate keeping up with stock orders.

payment is thrue Paypal or check ,,,, i hop in the next few months to get a card machine in the shop
Thanks
Duffy

I guess this is for building front axles only???? the cherokee d60 we had built is 52" from end of tube to end of tube......Im thinking that 48" is too short. or am I missing something here?

Did you get them full floater pucks done yet?
________
Godess_N_Passion (http://www.girlcamfriend.com/cam/Godess_N_Passion/)

I guess this is for building front axles only???? the cherokee d60 we had built is 52" from end of tube to end of tube......Im thinking that 48" is too short. or am I missing something here?

Brian, re-read the first page of this thread again. You do one side at a time, therefore only needing enough bar to get from the center section to one outer end.

Brian, re-read the first page of this thread again. You do one side at a time, therefore only needing enough bar to get from the center section to one outer end.

So this is not a full jig, you cant use to check for tube straightness against the other side. What would it cost to get a longer bar. It seems kinda odd you whould not have the jig to check.set it all? How do you check to make sure the axle is straight in the first place?

I see what your saying but my way of thinking is the axle shafts only go half way and with the bar going into both carrier bearings it would have to be damm close. I like the feal one can get when welding up one side at a time. I rotate the bar well I`m tig welding and can pull the weld with heat .
Duffy

I see what your saying but my way of thinking is the axle shafts only go half way and with the bar going into both carrier bearings it would have to be damm close. I like the feal one can get when welding up one side at a time. I rotate the bar well I`m tig welding and can pull the weld with heat .
Duffy

I guess but what do you see as damn close...I like em dead on. without that shaft going clear through you could be quite a bit off...Ive seen it before...a few times
So how much for a 70" bar?

Duffy,

I'm going to build a large 3.250" side bearing 9". I just bought the bar & the pucks to build the reverse 60 I was going to build. I only need the carrier or "side bearing" puck designed for the 35 spline axles. Do you make these? Thanks

Duffy,

I bought a 2.891 (Small Bearing) 3rd member at the Pick-N-Pul. I will use this 3rd member with the Jig. I will send you $99 via Paypal tonight. If you could please send the differential bearing puck ASAP it would be appreciated. I am trying to build this axle for EJS in a few weeks. Thanks

I'm interested in purchasing a set to narrow 60/70s are the full float wheel brg. bushings avaiable now? Can you ship USPS? Can you give me a price for the pair of diff. bushings, bar and full float bushing to 99654?

Thanks,
Gus

Received my set today, amazing fit & finish!

definately top-notch!

I agree with some of the other posts about the length of the bar so that it goes through both sides. Any chance of offering that as an "upgrade" to the setup?

Yes I well check on shipping costs for the longer bar ,,, one well need a second wheel end puck to.

Duffy

These are the jig bushings you need to shorten axles,,, I now make sizes for Dana 30, Dana 44, Dana 60, Ford 9" small bearing ,Ford 9" large bearing, Ford 8.8 , Corp 10 bolt , 12 bolt, 14 bolt and stock them. Other sizes not in stock well take about 3 or 4 days to ship.

A set of Bushings for the Differential run $99 a set including shipping

wheel bearing bushing for semi float or full float axles run $55 each including shipping

1 1/4" by 48" heat treated ground and polished bars run $120 including shipping.


( on the diff bushings one size will fit D44/60 and 14 bolt and the other size fits Ford 9" small & large,D30, and corp 10 & 12 bolt )

Duffy
D.D.Machine
(360)779-2500 shop #
(360)649-4465 cell #
Need a quote for everything needed on a Ford 8.8 rearend with shipping to 60441. And how long of wait on parts.
diff bushings
48" bar
wheel bearing bushings
Jeff 708-323-6857

Did you get them full floater pucks done yet?
What Jeff said.

When I talked with him in April he said he was going to do a run in June. Seems like a few people are interested. Maybe we can convince him to run them early.

It still looks like june tell I can get to the FF ends ... Duffy

I need a quote on the tooling for a D70 shipped to 65262
Thanks

It still looks like june tell I can get to the FF ends ... Duffy

Are the FF ends available now?

so why do some people use a Long bar ???

using a long bar you can check both sides. The nice thing about the long bar is you can still do one side a time (just more sticking out), then slide it all the way through to check the whole thing...

are you still selling these jigs?

tt

i'm interested as well...i'm looking for a D60 FF end and diff. pucks.
also I am hoping to use some 1.5" x .25" DOM as the alignment rod??
Can you bore the inner puck id to 1.5"?

So how much $$$ for 2 inner pucks and 1 outer FF end shipped to 30039?

Thanks,
Kevin

ttt

Hey all,
I tried calling the numbers listed for D&D and haven't received a call back yet, I am interested in getting a set up for a Ford 8.8 with small Ford 9" ends. Let me know!
Thanks
Mark

I spoke with Duffy yesterday.

I've been waiting 9 months to get the full float pucks and found out he made them and I "wasn't on the list".....

He said he's swamped with other work and won't be able to run any parts for 2-3 months. If he has them on the shelf you may get them. Otherwise don't hold your breath.

Good luck!

The D44/D60 chunk pucks and ford big/small chunk pucks well be done in a few weeks, its only the FF ends that I well not get to for a few more months , there kinda a bitch to make and I don`t have the time to screw with them at this time.

right know there is only two guys on the list for the full float ends and there not a hot seller,

( Sorry but I`m so backed up keeping product in stock that I can`t do custom work at this time)

Thanks
Duffy

Just noting to follow this thread. I will contacting down the road.

Tom

>>>nevermind just saw the last date notated by the thread starter<<< None the less I will follow.

My stuff ship yet. I'm the guy that placed the order back at the beginning of november. I've tried calling a few times two weeks ago with no luck in getting with you. Please PM me and let me know, thanks.

I just got done with a big run of ford 9" pucks and D44/60 pucks.

Hop to get a new run of the full float end pucks done in about a month.
Thanks
Duffy
D.D.Machine
(360)779-2500

Interested in the bar, full float bushings and pucks for D60. Can you shoot me a quote with an estimated turn around time?

any update on the ff pucks yet I am interested

Thanks

How big of a run are you going to do on the full float stuff? I'm going to be putting some 70 spindles on a semi float 60. do we need to get on a list? Got a ETA?

how do I get on "the list"?
i am looking for the full float inner, outer pucks, and alignment rod for a ff dana 60.
What kind of turn around time am I looking at and how much for everything shipped to 30039?
Thanks,
Kevin

I'd like to get in on the ff stuff also. Let me know when they are going to be available.

Gus

TTT for full float pucks

Bump for 60 FF pucks

Hey Duffy, Is this going to happen or should we just forget about it?

I'm also interested in everything needed to do a 14b ff both sides at once, and a bar long enough to go thru both axles on a 75" wms

Wow, he hasn't updated this since May? Must be getting plenty of business elsewhere and doesn't need ours:confused:

Do you still sell the items listed in this thread, or do I need to find another source?

you should find another sourse. This guy is long gone

Are you still in business?

If so, what's the leadtime these days?

Mike

Yes I still make them, I have dana 44/60 pucks in stock and set10,set20, ford big and for small wheel end bushings on the shelf. I well have a new run of ford big/small chunk pucks done in about 2 weeks.

I don`t know when I well find time if ever to run any more full float end pucks.

Thanks
Duffy
D.D.Machine

( call my cell at (360)649-4465 I don`t have a lot of free time to play on the computer )

Trying to get ahold of you. Messages at the shop number don't work and your cell phone seems to hang up on me instantly.

Same here I have had money in hand to buy kit and no response. I spoke to him once and I like his product. If you get this contact me at skidzjeep@sbcglobal.net or you have my cell on your shop voice mail. My name is Donald. I want to get 48" bar and semi float pucks.

Think I'll stand in line also

Do you happen to make a set for Rockwells?

Still making these?

ttt for Rockwells?

I gave up years ago. He was going to run more and I was first in line. Blah, blah, blah......

Called him a few times over a few months and got the same story.

This post should be deleted, it's a complete waste of everyone's time.

sucks this is NLA....... maybe one of the over site venders could pick up the slack with these..........

sucks this is NLA....... maybe one of the over site venders could pick up the slack with these..........

Venders, bueller, bueller.....

Search...

Searched.