PDA

: Got Slip ?????

TPIJeep
02-08-2002, 03:55 PM
I DO !!!! :D :D :D :D :D :D

Thanks Jesse at High Angle Driveline !
Welby
02-08-2002, 03:59 PM
:eek: Sweet :eek: :D
The Jerk
02-08-2002, 06:04 PM
yes i do actually
TheNerple
02-08-2002, 06:10 PM
Well I got about 3 feet of slip in each drive shaft and mine cost me 40 bucks for both! Can't beat 1/4 inch thick square drive lines! However those do look like rather nice drive lines. Think you "need" all that slip in the front?

http://photos.yahoo.com/bc/coiled1977/vwp?.dir=/My+Photos&.src=ph&.dnm=Under+belly.jpg&.view=t&.done=http%3a//photos.yahoo.com/bc/coiled1977/lst%3f%26.dir=/My%2bPhotos%26.src=ph%26.view=t
The Jerk
02-08-2002, 06:18 PM
actually thats a shot of my rear d shaft it has 12 inches of slip, and as for teh front d shafts you can never have too much in teh front, i cant even remember how many front d lines ive seen pull apart! jiMMy
TPIJeep
02-08-2002, 07:04 PM
Originally posted by Jimmy76FJ40
actually thats a shot of my rear d shaft it has 12 inches of slip, and as for teh front d shafts you can never have too much in teh front, i cant even remember how many front d lines ive seen pull apart! jiMMy

:D Thats 16" with 3" in the tube :flipoff2:
RE:Todd
02-08-2002, 09:17 PM
Yeah, I got slip, but mine are now 6.5 inches wrong. Damn, fawkin Marlin double.
Im4yotas
02-09-2002, 01:03 AM
Yah dude, that sucks about the marlin duals messin with driveline length requirements. Tell you what, since the d shaft is now the wrong length, I'll take care of it for you. Or even better, you can give me the dual cases so the shaft fits right:D
NE-RokToy
02-09-2002, 11:01 AM
Originally posted by Jimmy76FJ40
actually thats a shot of my rear d shaft it has 12 inches of slip, and as for teh front d shafts you can never have too much in teh front, i cant even remember how many front d lines ive seen pull apart! jiMMy

you worried about the rear driveshaft pulling apart or you just got to much money laying around? :flipoff2:
willymutt
02-09-2002, 12:12 PM
Why yes, Yes I do.


Erin
GhettoRig
02-09-2002, 12:31 PM
Not yet. Ordered mine from Jesse on Friday and should be here Wednesday.:D
ToyDozer
02-09-2002, 01:01 PM
Got BEEF!! Got SLIP!! Check Check!!
http://www.wheelingadventures.com/Truck/Mods/Shaft.jpg
21 spline 1-11/16" and HEAVY!!
onetoncv
02-09-2002, 08:45 PM
you get a zerk with that 1 11/16 bad boy? its a bit larger than our 1 5/8 spline that has proven it self unbendable and laughs at rocks - thanks for postin pics guys -Jesse
yjtj
02-10-2002, 06:53 AM
i do to, no pic though, jess is the man
44Runner
02-10-2002, 12:37 PM
No, but I will after this summer. Jesse will be hearing from me. Can't wait :D
ToyDozer
02-10-2002, 01:44 PM
Originally posted by onetoncv
you get a zerk with that 1 11/16 bad boy? its a bit larger than our 1 5/8 spline that has proven it self unbendable and laughs at rocks - thanks for postin pics guys -Jesse

Jeeze man calm down now!
This is just something that I turned out for myself so its basically a fancy square driveshaft! LOL!!

And yes the original plan was to have a zerk however I just havent gotten around to it yet.. Works pretty darn good even if it is way way overkill!

Heres a photo hack to show the original idea of where the zerk was going to go.. I was going to use two pieces of the reciever stock with about a 1" cavity in between the two then dimple the tube and use a button zerk.. Course like I said just havent gotten around to it yet!!
http://www.wheelingadventures.com/pics/Zerk.jpg

But hey, for a free driveshaft ya cant beat it!! The initial purchase gave me enough to build two shafts and the second shaft I sold which covered the entire cost!

I still love your shaft Jesse!! Dont get me wrong, but I dont think you were around when I made these...