brocbronc
04-18-2005, 10:05 AM
I have 1969 Ford Bronco
5.0 Cobra motor SEFI
brand new Centech wire harness for vehicle and engine harness from Fuel Injection Specialties
brand new radiator and shroud from BCBroncos
Brand new custom exhaust
NP435-NP205
has full top very good condition
93 honda prelude seats
front axle is Dana 44 with chevy 8 lug disk brakes. It had 4.10 and ARb but I removed them and used them some where else. (I still have a set of 4.10 gears and an open carrier for it).
Rear axle is Dana 60 narrowed to 60 inches wide to match the front (4.10)
dont know what type of lift, but it clears 38s. It is currently sitting on 39.5 boggers. I have a brand new set of 5.5 inch Wild horses progressive rate springs for it and a wristed radius arm. I have a shackle reversal kit which uses 3 inch full size leaf springs from F150 ( includes everthing needed except one shackle bolt and needs to be welded on. Hansens enterprises front bumper ( 1/4 inch thick throuout)
power steering-
has 2wd F100 box on the frame. The steering is all plumbed and working. I have a 78 f150 box and a 75 bronco box that will go with it if you want to mount the box outside of the frame rails.
This truck has some great parts and all axle and motor/trans/tcase are mounted in the vehicle. It was running and then we tried to switchout the wire harnesses to the new ones and it hasnt run on its own since.
http://pics.montypics.com/brewman/2005-04-18/1113843915_bronco_001.jpg http://pics.montypics.com/brewman/2005-04-18/1113843992_bronco_002.jpg http://pics.montypics.com/brewman/2005-04-18/1113844047_bronco_003.jpg http://pics.montypics.com/brewman/2005-04-18/1113844109_bronco_004.jpg http://pics.montypics.com/brewman/2005-04-18/1113844159_bronco_005.jpg http://pics.montypics.com/brewman/2005-04-18/1113844217_bronco_006.jpg
Asking $6500 OBO
power disk brakes
5.0 Cobra motor SEFI
brand new Centech wire harness for vehicle and engine harness from Fuel Injection Specialties
brand new radiator and shroud from BCBroncos
Brand new custom exhaust
NP435-NP205
has full top very good condition
93 honda prelude seats
front axle is Dana 44 with chevy 8 lug disk brakes. It had 4.10 and ARb but I removed them and used them some where else. (I still have a set of 4.10 gears and an open carrier for it).
Rear axle is Dana 60 narrowed to 60 inches wide to match the front (4.10)
dont know what type of lift, but it clears 38s. It is currently sitting on 39.5 boggers. I have a brand new set of 5.5 inch Wild horses progressive rate springs for it and a wristed radius arm. I have a shackle reversal kit which uses 3 inch full size leaf springs from F150 ( includes everthing needed except one shackle bolt and needs to be welded on. Hansens enterprises front bumper ( 1/4 inch thick throuout)
power steering-
has 2wd F100 box on the frame. The steering is all plumbed and working. I have a 78 f150 box and a 75 bronco box that will go with it if you want to mount the box outside of the frame rails.
This truck has some great parts and all axle and motor/trans/tcase are mounted in the vehicle. It was running and then we tried to switchout the wire harnesses to the new ones and it hasnt run on its own since.
http://pics.montypics.com/brewman/2005-04-18/1113843915_bronco_001.jpg http://pics.montypics.com/brewman/2005-04-18/1113843992_bronco_002.jpg http://pics.montypics.com/brewman/2005-04-18/1113844047_bronco_003.jpg http://pics.montypics.com/brewman/2005-04-18/1113844109_bronco_004.jpg http://pics.montypics.com/brewman/2005-04-18/1113844159_bronco_005.jpg http://pics.montypics.com/brewman/2005-04-18/1113844217_bronco_006.jpg
Asking $6500 OBO
power disk brakes