New LINK TABS added to site... Blue Torch FabWorks

[BlueTorch]

We have added a new setup for people who want their bottom links angled. The hole size is 5/8", but we can do custom hole sizes if you don't mind waiting a couple days. The tabs are laser cut from 5/16" steel plate.

The kit consists of 2 long tabs and 2 short tabs. You use one of each with each rod end and this will make the link angle off of the axle tube.

We make them for the follong

10 Bolt
Dana 44
12 Bolt
9 Inch
Dana 60
14 Bolt


Let me know if you hav any questions

http://www.bluetorchfab.com/oscomm/catalog/images/4linkangletabs.jpg

Thanks
Dan

[BlueTorch]

http://www.bluetorchfab.com/gallery/albums/grayghost/DSC01770.jpg


http://www.bluetorchfab.com/gallery/albums/grayghost/DSC01806.jpg

[JamisonWorkshop]

which one of those would be closest to 3 1/8" tube for toyotas. ???
Was wondering when ou would start having those.
Great quality as usual.

[ohmscj]

Looks great as always....Thanks for the kick ass products

[scott-885]

How much for some with 9/16" holes 2 sets shipped to 75229. Thanks.

[BlueTorch]

which one of those would be closest to 3 1/8" tube for toyotas. ???
Was wondering when ou would start having those.
Great quality as usual.

You can use the Dana 60 ones. We have them in stock with the 5/8 inch holes.

Thanks
Dan

[BlueTorch]

Looks great as always....Thanks for the kick ass products


Thanks for the props.

-Dan

[mikesagpn]

ordered my slightly adjusted set today
thanks for all the great service
AND super quick turn around!

Mike

[BlueTorch]

ordered my slightly adjusted set today
thanks for all the great service
AND super quick turn around!

Mike


thanks for the business. if you need any other parts let us know. If you need a custom part cut all you have to do is draw it with a pen and fax it over. We will qoute it and cut it if you like the price.

Thanks
Dan

[Devil Dog]

dan.. can i get 1 set for a 14 bolt with 3/4" bolt holes in them... shipped to 28540....
thanks

[Bigger Valves]

Dan,
Off the subject, but would it cost more to get some of your link tabs with 9/16" holes instead of 5/8"? I understand you don't stock in this size.

Also, is there a truss system for 60's for doing link suspensions? I'm getting limited on room on the pass side of my 60 to mount an airshock, lower link, and panhard rod. Then I gotta get an upper link in there somewhere. Do you make one or is it in the works?

[BlueTorch]

Dan,
Off the subject, but would it cost more to get some of your link tabs with 9/16" holes instead of 5/8"? I understand you don't stock in this size.

Also, is there a truss system for 60's for doing link suspensions? I'm getting limited on room on the pass side of my 60 to mount an airshock, lower link, and panhard rod. Then I gotta get an upper link in there somewhere. Do you make one or is it in the works?


I will do the tabs for the same price with the 9/16 holes. We are going to start stocking them with 1/2 inch holes so people can drill to 9/16 if needed.

We make a front truss system for a 60. You can check it out here.

http://www.pirate4x4.com/forum/showthread.php?t=343051




Thanks
Dan

[BlueTorch]

dan.. can i get 1 set for a 14 bolt with 3/4" bolt holes in them... shipped to 28540....
thanks

It would be a lot faster to get the 5/8" ones and just drill them. That is what I do in the shop normally if I need them with 3/4" holes. If you want me to laser them you would need to give me a few days to cut them. We are running about 3 days out due to the volume of work we have.

Thanks
Dan

[Devil Dog]

go ahead dan... im in iraq now.. so i have like 10 months before i can weld them on... let me know and ill shoot you the cash for them... thanks..
patrick