PDA

: Built HP 44

CA_YJ
05-10-2005, 05:42 PM
Driver side drop HP 44 front axle 67" WMS

HP 44
ARB
1310 pinion yoke
New 5.13 Spicer gears
Chevy flat top knuckles drilled and tapped, running hi steer
New Ford spindles
New Chevy 3/4 ton brakes
New Ford hub assembly (5 on 5.5 bolt pattern)
Hi-steer using 1 ton Chevy tie rod ends and 1.5" .250 wall DOM drag link and tie rod. (Both included in axle)
Warn Hubs
Warn Inner Axles
Randy's outer axles (chromolly)
Randy's u-joints
pic of u-joints...
http://www.moss-pultz.com/albums/axles/DSCN6420.sized.jpg

This axle was built from the ground up and the ONLY old parts on it are the Chevy knuckles and the housing. Every other part, bearing, seal has been replaced.

It is setup for a SOA YJ right now, but I can weld on new perches or TJ brackets if you want.

$2500
CA_YJ
05-11-2005, 12:53 PM
bump
CA_YJ
05-13-2005, 12:15 PM
again
SanDiegoCJ
05-13-2005, 01:20 PM
The link is dead Quinn.
geberhard
05-13-2005, 04:11 PM
Pretty good deal, try to post some pics.

G
CA_YJ
05-13-2005, 07:32 PM
Fixed the first link...

here is an old pic, still the same axle...just not as shiny. But I'll throw in a free can of spray paint:D
http://www.moss-pultz.com/albums/album01/DSCN5566_001.sized.jpg
dotrappe
05-14-2005, 02:57 PM
Last time I saw that axle, it was exactly as described! Fully rebuilt from the ground up! Pretty sweet setup!

Saw your last rag offering! Nice work! That is a lot of blue though!

Take it easy,

Dave from NM.
CA_YJ
05-14-2005, 04:36 PM
Hey dave...whats up man.

Time for me to build a new front...60 stuff with some 300M bling in the works
CA_YJ
05-16-2005, 08:33 AM
top
toyhunter
05-16-2005, 08:47 AM
would this work for a tacoma you know?
CA_YJ
05-16-2005, 10:51 PM
pretty sure tacomas are passenger drop. It wouldn't work unless you are swapping to an atlas or some other driver drop t-case
CA_YJ
05-18-2005, 10:37 AM
next...
joeylead
05-18-2005, 11:37 AM
would this work for a tacoma you know?


The axel could work on a tacoma. You would need to change the hubs to a 6 on a 5.5 bot pattern and maybe move the spring perches. But tacos are drivers side drop, the older toys are pass side drops.
CA_YJ
05-18-2005, 04:04 PM
changing to 6 on 5.5 is pretty easy...It would mean changing the hubs which aren't very expensive...it may also mean changing to chevy spindles, but I have a set sitting here that I would throw in with the axle. If you are not comfortable with changing hubs and stuff and wanted to convert it to 6 on 5.5 I could give you a hand...its really not that hard
CA_YJ
05-19-2005, 08:40 AM
top
CA_YJ
05-22-2005, 09:02 PM
top
CA_YJ
05-24-2005, 03:51 PM
Obo?
appx91
05-24-2005, 05:05 PM
So all shafts are Chromo?
CA_YJ
05-24-2005, 05:20 PM
Yup...all shafts and u-joints...all use full c-clips also
hoodrichxj
05-26-2005, 04:41 AM
I've got a buddy here in NC that's interested in talking with you about this HP 44. PM me with a number and i'll pass it on to him.