|
tigger4x 03-06-2002, 10:58 PM I am going to be picking up a DANA60 and 14BOLT and need to know what the measurements of the 60 are before I commit the $$$ and have to make quite a drive to fetch 'em. These are from under a military vehicle with 4:56 gears, posi front and Detroit rear. Can anyone help me with some accurate numbers please! WMS to WMS, center pin to center pin, spring pad width, how far is the diff from the pass. pad, etc. :beer: TIA!!! :beer: Aggro 03-07-2002, 06:51 AM 69" wms-wms if a single rear wheel I guess 32" spring pad to spring pad, might be wrong. mj 03-07-2002, 10:32 AM are you just trying to ID one? there are much easier ways to do that shock mounts look like chev stuff on the chev, and the dodge looks like a piece of bar stock welded with the shock pin in single shear Gozuki 03-07-2002, 07:43 PM Most important is spring to spring width, this will will tell me if I've gotta move his front springs or not. If it is 32", it will be a bolt in! tigger4x 03-07-2002, 08:48 PM WHOOOOOO-HOOOOOO ! ! ! I love it when stuff like this comes together!! :D tigger4x 03-08-2002, 05:48 PM Can anyone else verify if the measurements Aggro gave are accurate:question: THANKS AGAIN!! :beer: mj 03-08-2002, 07:26 PM yes the 32 is the rough measurement for the chev and the dodges are roughly a 1/2" wider tigger4x 03-09-2002, 05:51 PM The set I am getting came out of a Military Chevy. So IF indeed the width between the spring pads is 32" I am set!!! :smokin: :D :smokin: tigger4x 03-16-2002, 07:44 PM PAUL or anybody else with some good Chevy D60 confirmation information?!? Aggro 03-20-2002, 08:37 AM I didn't realize this post was still going. I can go home and measure tonight to get final numbers. tigger4x 03-20-2002, 07:04 PM AGGRO ... Thanks man! I'm pretty sure of the numbrs but don't wanna get caught on the short end of the stick. :D :beer: Aggro 03-21-2002, 09:50 AM DOH! I forgot. what all should I measure? mj 03-21-2002, 05:26 PM centre to centre of the spring mounting pads tigger4x 03-21-2002, 05:44 PM Thanks MJ! AGGRO ... I need the measurements from centerpin to centerpin on the leaf springs. Could you also lemme know how close the spring pad/perch is to the diff?!? THANKS AGAIN!! :beer: mj 03-21-2002, 09:44 PM I am curious how many people have to tell you 32 before you believe it? Aggro 03-22-2002, 08:21 AM you ready? center of housing to top of spring perch 3 3/8" tie rod is 56 1/8" long perches appear to be 31 3/4 on center Aggro 03-22-2002, 08:22 AM another, same dim Aggro 03-22-2002, 08:23 AM driver side perch width 3" Aggro 03-22-2002, 08:24 AM passenger perch +2.5" Aggro 03-22-2002, 08:25 AM center of housing to bottom of diff roughly 6 1/2" tigger4x 03-22-2002, 04:40 PM :eek: DAAYYYUUUUUMMM AGGRO ! :eek: You are the :nuke:!!! Talk about the detailed details!:D No pea pickin' bout a doubt it! :laughing: Have a :beer::beer::beer::beer::beer::beer: on me bud !!! Iffin we ever meet up I'll have 'em nice n chilly!! THANKS AGAIN !! | |