|
: Will 88 doors fit on an 85 truck? Entropy 03-28-2002, 04:17 PM Subject says it all... I didn't find anything searching. I assume anything from like 84 - 88 should be interchangeable but I wanted to make sure. Thanks... grshpr 03-28-2002, 04:30 PM Yes they are the same 2wd and 4wd are the same too also 4runner doors are the same. SeaBass44 03-28-2002, 04:33 PM 84-88 trucks and 84-89 4runners same:) Entropy 03-28-2002, 04:43 PM Thanks guys... you are just dreamy!! :D SeaBass44 03-28-2002, 05:10 PM Originally posted by Entropy Thanks guys... you are just dreamy!! :D :rainbow: :rainbow: :rainbow: :rainbow: :rainbow: :rainbow: :rainbow: :rainbow: :rainbow: :rainbow: , keep that up and be banished to JU 4 Life!:flipoff2: DToy 03-28-2002, 08:19 PM You can also swap windows-frames and hardware. The door frames will accept either one-piece windows or vent windows if you swap the window tracks and moldings. Entropy 03-28-2002, 10:22 PM Originally posted by SeaBass44 :rainbow: :rainbow: :rainbow: :rainbow: :rainbow: :rainbow: :rainbow: :rainbow: :rainbow: :rainbow: , keep that up and be banished to JU 4 Life!:flipoff2: I don't know what would suck more... the banishment, or the fact that I don't have a Jeep and I would be in Jeep country... ...you're right, it would be the banishment. Seriously though, my wife was listening to Enya... and it was totally seeping into my blood stream and provoking some wierd :rainbow: reaction. :flipoff2: Entropy 03-28-2002, 10:23 PM Originally posted by DToy You can also swap windows-frames and hardware. The door frames will accept either one-piece windows or vent windows if you swap the window tracks and moldings. Actually... the thing I am most worried about is swapping my power shit... cause the doors I am getting don't have power and mine do. Since I am a sissy bitch, as demonstrated by my earlier post, I don't want to go back to manual. Shane 03-28-2002, 10:48 PM The power stuff will bolt right in, no worries. :beer: Kamster1200 03-29-2002, 05:38 AM I bought an '85 Reg cab truck that had the pass. door replaced. I am pretty sure the drivers is stock, and I am guessing the pass. side is from an earlier model. There are some minor differences, The r. door has an inside door panel that does not go all the way down the door. The r. side inside door handle is metal, the left is plastic. I have seen at least three flavors of arm rest for those years, with at least two different bolt patterns. Entropy 03-29-2002, 08:19 AM Originally posted by Kamster1200 I bought an '85 Reg cab truck that had the pass. door replaced. I am pretty sure the drivers is stock, and I am guessing the pass. side is from an earlier model. There are some minor differences, The r. door has an inside door panel that does not go all the way down the door. The r. side inside door handle is metal, the left is plastic. I have seen at least three flavors of arm rest for those years, with at least two different bolt patterns. Well, thanks for the info... I am not sure whether it is fortunate or not... but these doors are coming stripped. The reasoin I want them, is that aside from some custom pinstriping (a la tree branches) they are perfect. Dents and scratches don't bother me... Rust bothers me. Mine are rusting at the mirror mounts, have bad weather stripping, bad locks, rust holes, multiple dents, fawked hinges... basically good half door candidates. So the new ones are getting my interior panels, power stuff, new solex locks, new mirrors (as soon as I find some - I can't remember if they were included), quick release hinge pins, new weather stripping depending on current condition, and some spray paint. Then the old doors get cut up and converted to half doors. (Gotta love trying to do anything with a daily driver). | |