Your JMR super hook-up Yeeaaay!:

JMR Manual Bender (http://www.polyperformance.com/shop/product.php?productid=206&cat=90&page=1)

JMR Tube Notcher (http://www.polyperformance.com/shop/product.php?productid=206&cat=90&page=1)

1.75" x 6" radius 120 degree die (http://www.polyperformance.com/shop/product.php?productid=485&cat=191&page=1)

Bend-Tech Software

$1550 shipped anywhere in the lower 48. :fj:

http://www.polyperformance.com/shop/files/t_434.jpg

http://www.polyperformance.com/shop/files/t_485.jpg

http://www.polyperformance.com/shop/t_206.jpg

http://www.pirate4x4.com/forum/attachment.php?attachmentid=228664&stc=1&d=1139363236

what are the differences between this bender and a JD^2?

why the extra ~$200?

Your link to the bender is wrong.

http://www.polyperformance.com/shop/product.php?productid=434&cat=189&page=1

is the correct link to the bender. The JMR benders are badass. They are much stronger than the JD2 benders, when you change dies you do not have to take off the arms of the bender. The quality difference between the two is amazing. We've got JMR's hydro bender in the shop, and we could not replace it.

Looks nice. Now lets see how many pennies I have in my pocket .....

Cool only $1549.97 left :D

what are the differences between this bender and a JD^2?

why the extra ~$200?

REASONS YOU SHOULD SPEND A LITTLE EXTRA:

-Bender is made from all billet material and guaranteed for life.
-It uses sealed roller bearing at all the pivot points.
-Won't fall apart when changing dies.
-Arms are constructed of high carbon heat treated steel.
-Arms are also Blanchard ground so they are perfectly flat and square.
-The bender comes with a handle and quick release pin.
-The JMR bender has 3 times the leverage of a JD2 bender which means only a 1/3rd of the force is required to do equivalent bends.
-JMR has an anti spring back device that is available.
-All the dies are heat treated and come with a life time warranty.
-The dies also come with roll pins so the follower die lines up exactly every time you set it up.
-The bender can also be upgraded at anytime to the ratcheting mechanism or full hydro.

If thats not enough reason to spend a little extra I am not quite sure what is.

sounds great! id just never heard of them before....thanks for the info

how much for just the bender and a 180 degree die 1.5"

how much for just the bender and a 180 degree die 1.5"

Check your box.

do you take purchase orders from schools? pm response ok..


chris

do you take purchase orders from schools? pm response ok..


chris

Sure, if you plan on paying with US currency.

bender, 1.5" x 240/degree die, degree ring/stop shipped to 98946??? please

bender, 1.5" x 240/degree die, degree ring/stop shipped to 98946??? please

Check your box.

How long is this special good for?

It's still going...but it's not going to last forever. What do you need?

Which bed tech software is it?? Thanks

Which bed tech software is it?? Thanks

Bend Tech EZ

price for bender, degree ring, 1" and 1.5" dies shipped to 92064.

thanks

price for bender, degree ring, 1" and 1.5" dies shipped to 92064.

thanks

Check your PM's

price for bender,degree ring,1.5"x240* die. shipped to 98444

price for bender,degree ring,1.5"x240* die. shipped to 98444

Check your PM's.

Its good deal TTT

purchased a bender, three dies and the notcher... will be picking up this weekend... cant wait!!!!


chris:cool2:

looking for a good bender for schd 40 3/4, 1. and 1 1/4 with 240 dies .

i have read alot of feed back about your benders and you have definatly got my interest .

i own a small metal fab shop here in wasilla alaska what would this cost me to ship here @ 99654 for the entire set up ready to go with above sizes dies . to include notcher ..

thanks again

wayne

How much for just a bender or mechanical bender, degree ring, notcher, and 1.75"x6x240 die shipped to 76310?

purchased a bender, three dies and the notcher... will be picking up this weekend... cant wait!!!!


chris:cool2:

So how about an update....? How the new bender working out..?

how much would it cost if i came and picked it up

pricing on a full set up w/wo hydro and pump and mechanical and 1.5" and 2" 240 deg round tubing dies, will pick from SLO, shoot me and address, we are going to Pismo this week...Mo in Clovis

how much would it cost if i came and picked it up

Same price.

How bout bender(mech and manual) 1.25 and 1.75 240* with degree ring to 85381?
Thanks

How bout bender(mech and manual) 1.25 and 1.75 240* with degree ring to 85381?
Thanks

check your pm

Called the order in today and spoke to Dave.

Thanks

Thanks for the orders

orderd the full hydro bender with 5 dies tues. counting down the days. this is going to be a sweet upgrade from my pro-tools
tony

thank you for the orders

Can you just get me the degree ring,and how much shipped to 89014.

How much for a 1.25 / 240* die set shipped to 85381.

Thanks

OK guys, got you both.... Anyone else.....?

So how about an update....? How the new bender working out..?


Just saw this today... Works killer, very easy to bend even though its not hydro... Quality is TOP NOTCH and when changing dies it dosent fall apart like other benders do... (Makes it easier to change when you dont have to worry about lining up the arms to get the pin all the way in)

Now I need a price on one for me :D


Mechanical bender, (base model) 1.5" 240 deg die, no shipping....


Hope you guys have an awsome Christmas!!!


Chris:cool2:

Ttt

Price for Bender degree ring, and stand with a 1 3/4x 6x 240 die to 94062. Thanks.

PM sent

how to swap out for a 2" die? thanks

price on the bender(handpull w/deg ring) with 2"/1.750/1.5 240deg dies and the notcher shipped to 95670 please?

have the jmr dimples. you can not compare the machine work to any others. very nice pieces. i have no problom paying more for quality tooling. you get what you pay for people! if your tools are your living like mine. dont buy crap!

ttt

how much for manual bender , 1.75 240 deg dies and degree ring to 28173

Hey guys.....

Im new to this forum....I own a custom shop in CT doing mostly air ride setups and custom frame work..... Im so glad I found this thread cuz i was up in the air about the Pro Tools / JD2....This thread gave me the answer....neither!!! lol.....

Can you give me a price on,

(1) Air over Hyd bender
(1) Degree Wheel
(1) 1 1/4" 240 degree die

Shipped to 06492
Thanks,
Jon