Dedenbear Dana 44 Knuckles Are In!!!!!!

[Highonda]

Guys,
the dana 44 knuckles are in and ready to ship!!!!

Chevy are $219 each to your door
ford are $249 each to your door
scout are $249 each to your door
4 hysteer stud kit w/nuts and cones $55 a side
chevy spindle studs $16 a side
ford spindle studs $12 a side

thank you
please remember we take credit cards, paypal or m.o.'s

paypal is: highonda@optonline.net
call 845-598-0545 with cc info

thanks again
doug

[Highonda]

Pic

[Highonda]

Features Include:
CHEVY:
Cast from high strength ductile iron
Beefed up with extra material and ribbing
Flat tops machined and drilled for high steer arms
4th bolt hole for high steer arms increases clamping force and sheer strength
3 bolt high steer arms still fit
3/8" thickness added to flat top of the knuckle for high steer tie rod to leaf spring clearance
Cast-in DUAL steering stops eliminate bent stop bolts that can cause u-joint and axle failures
Tapered tie rod holes accept factory tie rod ends
Tie rod holes can be drilled to accept 3/4" heim ends
Powder coated bright orange for long lasting looks
Interchangeable with all factory and aftermarket Dana 44 components
Fully machined and ready for installation
Machined to clear CTM u-joints without removing the grease fittings
Tie rod hole is tapered from the top to the bottom
Will fit 10 bolt and early Dana 30 axles with minor modification.

FORD:
Cast from high strength ductile iron
Beefed up with extra material and ribbing
Flat tops machined and drilled for high steer arms
4th bolt hole for high steer arms increases clamping force and sheer strength
3 bolt high steer arms still fit
3/8" thickness added to flat top of the knuckle for high steer tie rod to leaf spring clearance
Cast-in DUAL steering stops eliminate bent stop bolts that can cause u-joint and axle failures
Tapered tie rod holes accept factory tie rod ends
Tie rod holes can be drilled to accept 3/4" heim ends
Powder coated bright orange for long lasting looks
Interchangeable with all factory and aftermarket Dana 44 components
Fully machined and ready for installation
Tie rod hole is tapered from the bottom to the top
Based on the Bronco disc brake knuckle and fit 1/2 and 3/4 ton brakes
The only aftermarket knuckle available for a Ford Dana 44.

[Highonda]

Wow,
Nobody Interested?

Let Me Know
Thanks
Doug

[rajincajingt]

do you guys do arms too?

[Shady TJ]

Doug is out at Spring SEMA give him a few days to get back to you.

[Highonda]

thanks bruce,

currently, i am looking for a mfg to supply me with dana 44 arms,
i have dana 60 arms that we make but not 44's
thanks and let me know on the knuckles.

doug

[Buddha]

I'm interested, but who makes arms for these?

[Highonda]

i know btf is working on some for these knuckles.

thanks
doug

[Highonda]

ttt

[Highonda]

ttt

[Highonda]

Ttt

[Highonda]

pm sent,

happy 4th

thanks
doug

[Highonda]

ttt

[Buddha]

Any arms for these yet???

Tim

[Buddha]

Is this thing on?? Doug!! What's the word??

Tim

[Nordic1]

Do you sell the 4 bolt highsteer arms for these guys?

[Highonda]

honestly, i do not have a line on them yet.

i will make some call tomorrow

thanks
doug

[Highonda]

Guys, I Have The 44 Arms With The 4 Holes For The Dedenbear Knuckles.

They Are $90 Each

They Come With 10 Degree Correction

We Have Them In 6" Or 7.25" Lenght From The Ball Joint

They Are Tapered For The Tierod.

The Stud Kit (4 Studs, 4 Cones, 4 Washers) Is $44

Thanks And Let Me Know

Doug

[zkrawler_04]

was wondering if these knucks would work with a dodge 44 with out the locking hubs or the drive flanges i guess they are some type of unit bearing design

[Highonda]

i will check with dedenbear if they have any info on that application.
and will post
thanks
doug

[Highonda]

thank you for your support

doug

[Highonda]

Ttt

[Highonda]

ttt

[Highonda]

ttt

[Highonda]

ttt

[Highonda]

ttt

[TOYOTAJUNKIE]

do you have the knucks for a 1978 ford d44 with arms?

also do you have any used dana 60 axles for the same year


shiped to 95472


thanks

[Highonda]

Pm Sent

[dcadwell]

Looking to get Solid Kingpin knuckles for chevy dana 60 and their high steer kit. Also needing 1 14 bolt single wheel rear hub. All parts are for late 70's axles. Dana 60 I got from you. Thanks

[apeters89]

Just curious, does dedenbear (or is it Reid now?) sell Dana 44 inner C's to go along with the knuckles? My inner C's have seen better days :(

[Highonda]

Pm Sent


Thanks
Doug

[Highonda]

updated