|
SeaBass44 04-05-2002, 05:15 PM friend has a 1990 2wd xcab v6 5speed, rear end is whinning, wants a 3rd what is it? a 7,5 with what ratio? says g382 code on the door sill, any help out there today? or this weekend, no hurry, I'll see if I can find that site on orc I think had the code breaker? looks like the 7.5" Lowtorious 04-05-2002, 05:45 PM you of all people? I know it's been talked about a bunch of times... DavidT. 04-05-2002, 05:46 PM It might be an 8-inch? I found this link http://www.off-road.com/toyota/tech/other/4_axles.html but kinda hard to make sense out of it. Good luck! DavidT. 04-05-2002, 05:49 PM I think I figured it out :D :D G means 8-inch, 3 means 3.545 gears and 2 means 2-pinion. G382...don't know what the 8 between 3 and 2 means.... :rasta: :smokin: SeaBass44 04-05-2002, 06:04 PM Originally posted by DRT12 I think I figured it out :D :D G means 8-inch, 3 means 3.545 gears and 2 means 2-pinion. G382...don't know what the 8 between 3 and 2 means.... :rasta: :smokin: sweet, the g does mean 8" hu, I'll gfo look at the 85 1 ton I have.see what code it has. toy283 04-05-2002, 06:19 PM From the above listed ORC page: G - 8" diff 38 - 3.417:1 gears 2 - two pinion SeaBass44 04-05-2002, 06:20 PM ok if I read this right. the G382 is a 4:10 01 = 3.42 02 = 3.58 03 = 4.10 04 = 4.56 05 = 3.15 06 = 3.91 and my 1 ton is G282 so it's a 3.58 look right or wrong guys?;) jasonmt 04-05-2002, 06:20 PM Originally posted by DRT12 I think I figured it out :D :D G means 8-inch, 3 means 3.545 gears and 2 means 2-pinion. G382...don't know what the 8 between 3 and 2 means.... :rasta: :smokin: G=8" Ring, 38=3.417 Gear Ratio, 2=2 Pinions, if it was a 3.545 Ratio it would be a 03, not 3 jasonmt 04-05-2002, 06:25 PM Originally posted by SeaBass44 ok if I read this right. the G382 is a 4:10 01 = 3.42 02 = 3.58 03 = 4.10 04 = 4.56 05 = 3.15 06 = 3.91 and my 1 ton is G282 so it's a 3.58 look right or wrong guys?;) SeaBass: you are looking at the table for vehicles with a VIN starting with 4Txxxx, the table above it is for Japanese built trucks with VIN'S starting with JTxxxxxx. G282 will be a 8" with 4.30 gears and 2 pinions if the VIN starts with JT. DavidT. 04-05-2002, 06:27 PM Originally posted by jasonmt G=8" Ring, 38=3.417 Gear Ratio, 2=2 Pinions, if it was a 3.545 Ratio it would be a 03, not 3 I knew that...I was just check'n to see if you guys were paying attenting :rolleyes: SeaBass44 04-05-2002, 06:30 PM Originally posted by toy283 From the above listed ORC page: G - 8" diff 38 - 3.417:1 gears 2 - two pinion Ok I understand now:D so the G282 in my 85 2wd 22re 5speed p/u is a 4.30 and seems it's a w56 trans thx everyone | |