Does anyone know where I can find tapered reamers and reverse thread taps? I know I can get the 1.5" & 2" tapered reamers from Stock Car Products and Midwest Motorsports, but neither sell the reverse thread taps. I want to do my shopping at one place if possible.
Thanks :D

PS Baum Hydraulics sells parts to build your own Hydraulic cylinder.

MSC or McMaster Carr or Grainger. All have net sites...Too lazy to search for ya....

Here are two that blow away Graniger an Mc Master Carr.

www.travers.com

www.jlindustrial.com

You could try www.speedwaymotors.com also!
Steve

Originally posted by Ultim8kaos
You could try www.speedwaymotors.com also!
Steve

yikes! everyone needs a $3400 tubing notcher

http://www.speedwaymotors.com/product.asp?source=2191&base%5Fno=91089465&str%5Fbase%5Fno=91082730%2C91083110%2C91083895%2C9 1084100%2C91085172%2C91087100%2C91089175%2C9108940 1%2C91089402%2C91089403%2C91089404%2C91089406%2C91 089409%2C91089410%2C91089411%2C91089431%2C91089451 %2C91089452%2C91089460%2C91089465%2C&header%5Ftitle=&page%5Fname=prod%5Flist%5Fdisplay%2Easp&search%5Ftype=L1%7E242&size1=&size2=&gender=&ShowImages=yes&sq=100&cont=1&intPgNo=6&mscssid=TC0NK2J5B6H19LFQPCB0H0UNSU1T52CE

- jack

check this bender out, not bad for $400

bender (http://www.speedwaymotors.com/product.asp?source=2191&base%5Fno=91084100&str%5Fbase%5Fno=91082730%2C91083110%2C91083895%2C9 1084100%2C91085172%2C91087100%2C91089175%2C9108940 1%2C91089402%2C91089403%2C91089404%2C91089406%2C91 089409%2C91089410%2C91089411%2C91089431%2C91089451 %2C91089452%2C91089460%2C91089465%2C&header%5Ftitle=&page%5Fname=prod%5Flist%5Fdisplay%2Easp&search%5Ftype=L1%7E242&size1=&size2=&gender=&ShowImages=yes&sq=100&cont=1&intPgNo=6&mscssid=LL80UBXWJX2B8GPDCRGXWP5936S197K2)

i saw that bender, i'm guessing the $439 gets you the bender hydraulic jack and one die ??

- jack

Man I didn't realize I could get everyone in trouble so quick. :rasta:
JD squared has the base unit for $325 and the dies for $90ish.
http://www.jd2.com/M3B.htm

Pro Tools has one that is good, they seem to be a little higher.
http://www.pro-tools.com/mb1054.htm

I have another link, but can't find it at home. That one is the one I'm getting when I have $400 laying around, the dies were better priced than the ones above. Still same basic design though.
Pro tools has a computer program for bending, not sure if it is worth a crap.

hey oldmule, we're well versed in the virtues of the jd2. check out the bending 101 article in the Tech section. alot of guys here have either the jd2 or the pro-tools bender.

i just thought that was an interesting setup with the manual pump, though i'm sure it's quite slow and tedious to work with being a manual pump with a short stroke.

- jack