FOR SALE


MODEL # 3414070...ARB winch ready BULL BAR

-FITS IFS PICKUPS/4RUNNERS FROM 86 TO ???...STRAIGHT AXLE TOY'S ARE A DIFFERENT NUMBER, BUT MAY ALSO FIT...

-has been installed and removed, but not winched on or "run-aground"..:D

-fits most ramsey, warn, milemarker, tmaxx winches, but do your research cuz some won't fit

-there are minor dings from installing it, but the powdercoating is 99.9% perfect.

-all hardware and instructions included.

-purchased in April 06, but had to sell vehicle to pay for college. :(


I paid 800 bucks for it (739.00 + tax + freight) at 4wheelparts

NEW REDUCED PRICE...600.00, COME GIT IT.


I'M OUTA TOWN FOR THE SUMMER. IF YOU WANT THE BUMPER, I CAN HAVE MY IN-LAWS IN SAN DIEGO TAKE CARE OF THE DEAL (TAKE YOUR MONEY/GIVE YOU THE BUMPER). I'M ENTERTAINING TRADES AT THIS POINT....GUNS, BIKES, MONEY, CHEAP 4X4'S ETC(have to be running)... MAKE ME A "REAL" OFFER.:)

..

used...i would only pay half of what your asking. so that makes the correct price, $340 tops. let me know 'buddy'.

im singing the "never gonna sell to you" song over here....

...

...

...

11

.

$340 is a fair price for a used bumber. i am looking at my ARB used bumber now. paid something like $250 for it off this board two weeks ago. the original owner paid $800. bumpers lose their value when used:p

$340 is a fair price for a used bumber. i am looking at my ARB used bumber now. paid something like $250 for it off this board two weeks ago. the original owner paid $800. bumpers lose their value when used:p

...thanks for the tip, mossy. you wanna cookie or something?

Send me the measurements on it and a couple pic's of the backside where it mounts, It may be about the right width for my Commando.

will do

this is the main mounting area...the yellow width is 25.5" to the inside of each mounting horn

also, you can see that there are three holes at each end of the transverse mounting area. the horns themselves have two main holes and a large cutout hole for use with an offset washer for differences in frame dimensions.

here you can see three of the transverse mounting holes...and you can also see the two main holes in the mounting horns..

you can also see the large cutout in the rearmost hole for a wrench to fit into.

the pic is dark, but you should be able to see one of two total vertical holes that mounted to the face of the crossmember on my yota...

on this side only there are 7 total mounting holes...for a total of 14 mounting points..hehe..talk about beefy :)

the bumper from end to end is 67" wide

in this pic you can see the ancillary mounting horn. on my yota, it wasn't used so i don't know exactly how it supports the weight of the bumper or winching.

its width, however, is 37.5" from the inside of one mounting area to the other on the opposite side of the bumper.

by the way, the brown you see is just dirt.

there are a few scratches from the trucks frame (from mounting it by myself) but is mostly just road dirt.

...

...

...

still for sale...someone trade me something and i'll have my inlaws in san diego give you the bumper...

how bout your junker 4x4...or something fun...money, guns, etc.

...

111

...

can you ship it? and at what cost?

hey big boss,
shipping would be kinda difficult since im about 1250 miles away from it right now...

sorry. mebbe at the end of the summer, if i still have it and im back in san diego, i could weigh it and see.

who goes online when they're on vacation? lol

who goes online when they're on vacation? lol


again, you show good reason that it was a mistake to give you opposable thumbs....im not on vacation...


retard.:shaking:

if i were to go to hawaii for school or work, i still wouldn't be online! go do something...geez

blady blah, thanks for the bump.