anyone done it??????

I'm thinking I can make it work, whatcha think???????

If you dont mind hacking the fenders, I'm sure it can be done.

fatkid says 40's work well on the stock axles, so no worries there. :grinpimp:

Originally posted by Shrock
fatkid says 40's work well on the stock axles, so no worries there. :grinpimp: Fatkid put his sack on my face!!!!
He knows what is in the works:vader2: :vader2: 0

Fatty is the man and I wish I was as pimp is as hime as a matter of fact I use to ho for him..s:flipoff2: :flipoff2:

LR jr will soon be on his knees in front of the fatkidl:eek: :eek: :eek:

OK Fatty thats goin to far:flipoff2:

my Ho'n was suppost to stay quiet:eek:

What you forgot to mention is that I belong to you and that your going to make me pay for running my mouth.:flipoff2: :flipoff2:

Your the man fatkid.:) :)

:confused:

37's are easy, SOA and 12" blocks. good to go. body lifts are :rainbow: :rainbow: :rainbow: youre probably going to need to move the front axle forward quite a bit. I've hacked quite a bit and my 35's still rub in the back.

I don't know how much lift I got from my coils, but I hacked the shit outta my fenderwells and I have plenty of room to spare. I would suggest pulling the axle forward a bunch and moving the rear end back a little too, so that you have more room for the tires and a more stable ride. I would say with a simple spring over, a little shackle, and lots o' sawzall you should be fine! What do the 37" MTR's actually measure? Cause my 37" boggers only mearsure 35.4" tall. So, what do you have planned for your sammy?

Sure, do it. I'm about to put some 36" TSLs on mine. It has SOA w/ wranglers. The front axle is moved forward about 1.5", rear has some little blocks to help. I'm just going to cut and pound for a perfect fit. The 35" BFGs on it now just barely rub.

I dont have a body lift on mine, and 37 would fit no problem. I wish I didnt already have my 35s...doh!

I enlarged my rear wheel wells and tossd the front clip, and am running stock yj and cj springs in a spoa. From what I can tell youd have a hard time keeping 37s out of the firewall without extending your frame a little more than I did or using springs with a lot of offset in the pin. I am looking at using toy rears in the front eventually (2.5 inch offset, but the same length as yjs) when I go to biger rubber.

Hack em' and move your axles some!!! A little sawzall action never hurts :flipoff2:

Originally posted by nuttzack
So, what do you have planned for your sammy?

OK here is the begining plan

sammy frame and body
22re
toy 5 spd
toy 4.7 t case
toy axles
yj SOA
hy-steer
toy pwr steering
front axle moved forward
rear moved back
moto masters steel work
37" mtr's or 36" sx's
locked F & R
winch
premier power welder
and one FULLY hacked body to keep it low

anything else you guys would add????

If you guys are wondering if I can pull it off, do a search for LeRoy and LeRoy II to see what I have built before the sammy project:flipoff2:

FatKidd is my Master:vader2: He has pulled me to the other side:trooper: :trooper:

sounds like you just need a sami body and a rolled toyota to put it on......now I will duck backs into my fox hole but seriously that sounds reallly cool

sounds like the toyota I just sold except it did not have a welder and it had a toyota body...really.swithched over to sami to get smaller and lighter

Originally posted by Frosty "The Legend"


22re
toy 5 spd
toy 4.7 t case

Why not just use:

1.6 16V
sammi 5sp
6.1 Sumo or 5.8 Calmini

A lot less work and still very capable. Lower gears too.

or instead of one 4.7 box use dual stock boxes ,I think your double low will be equivalent to 5.28 to 1 or just add a stock box to the front of the 4.7 to get really down in it .Turns into a heavy set up then but its all center mass,could be good to ballance the rig

i'd say dual cases as well, just more options, plus that extra shifter is just cool

Frost like Toy stuff, not to mention he get most of his Junk for almost nothing.:)

Leroy

LeroyII

I think you should put those DynaTrac HP 60's you have under your Zuk. However I think you might be brake those 1.5" alloy shafts your running.:flipoff2:

FK you think I could do it??????

HMMMMM hp60's in a Sammy:smokin:

Nah too heavy, PS. called shaffer today:flipoff2: :flipoff2:

Originally posted by fatkid
Leroy

I remember this one!!!

Fatty, when are you going to make it up this way??

FK you think I could do it??????

I'm SURE dual toy cases will fit! :D I'd reconsider using the much heavier toy motor, but your plan sound good to me. Sound essentially like my rig, I'll let ya know how it works in the next couple of weeks!

Thats the same set up that I have except that I have 22r insted of a 22re and I'm running coilsand a dual case set up. If you want to see pics of it E-mail Kerry Wittig at 1.6toy@msn.com .

Originally posted by Frosty "The Legend"
FK you think I could do it??????

HMMMMM hp60's in a Sammy:smokin:

Nah too heavy, PS. called shaffer today:flipoff2: :flipoff2:

Frost is talking about his High Pinion Dyna Trac Dana 60's with 1.5" alloy axle shafts.:)

37 MTRs with light sawzall :rolleyes:

Youll love your Sami dude....
I like my 1.3 though.... 5.89 d44's with GRS2
http://www.sierrarockcrawlers.com/community/sam/a5.jpg


Mike-

dont forget to build it into a POINT and SHOOT rig... leave the suspension firm for boulder jumping and it will Slam over anything....

Mike-