offroad_joe
10-03-2006, 07:35 PM
http://www.supermotors.net/getfile/94918/fullsize/pict0071.jpg
http://www.supermotors.net/getfile/94916/fullsize/pict0062.jpg
Chevy 350 TBI with affordable EFI harness and Computer.
New Aluminum 2 Core Radiator with Ford Taurus Fan and DC Controllers Temp Controller.
Rebuilt Turbo 350 Reverse Manual Valve Body Trans.
Large Heavy Duty Trans. Cooler With 10" Fan Mounted in Bed.
Dual 23 Spline Cases, Fresh Rebuild on Marlin 4.7 case W/Cryo Treated output shaft. Bud built Dual Case Cross member and Skid Plate.
Front And Rear Square Tube Drive-Shafts.
Front Axle has a Lock-rite Locker With 4:10 Gears. Longfield Old Style Treated Birfs, All-Pro Cromo Inner Axles.
85 Rear Axle With A Spool And 4:10 Gears, Sky Manufacturing Rear Disks.
Large Master Cylinder With Residual Valve And Adjustable Proportioning Valve.
Electric Line lock For Brakes, Also an All-Pro T/Case Brake That needs some work.
37" Mickey Thompson Baja Claws on black steel wheels.
Front Has Rancho 4044 Springs, Rear has 63" Chevy 4" lift springs. (No Block)
Shocks Are nothing to write home about. (Junk)
EXO Cage, Front Bumper and Sliders built by Rob Parks AKA Bender.
3" Body Spacer.
Fiberglass Front Fenders, Pinned hood With Small Air-Scoop.
Front and rear Rock Lights, Hella Driving lights.
The pictures Posted were when the cage was new and had not seen the rocks yet, so needless to say it has some rock rash on it. Several test paint patches and a couple of dents.
Body is in good condition, paint sucks, Doors have been stripped of paint. I have about a dozen rattle cans of primer and another dozen or so of Chevy Engine Orange if so desired.
Tube bed could use a Rebuild to match cage tubing. But is functional.
Sliding Rear Window is out and doors are completely disassembled, I have two sets of door windows and all hardware to reinstall either manual or electric windows.
Mazda RX3 seats with 4 point harnesses.
New Reverse Pattern Ratcheting Floor Shifter.
Stewart Warner Gages in original location. Water Temp., Oil Pressure, Trans. Temp, Oil Temp,Volts, Tach And Speedo.
This rig has wheeled Aftershock, Wreckingball, Big Johnson, Claw and Sledge at the Hammers.
I'm sure there is more but I'm crying thinking about all the money I have put in this rig. :crybaby: My loss someone else's gain.
It is street registered and green stickered in Calif. But the street plates have been no opped.
I want $5500 for this rig, pickup in Southern California. If you don't want a V8 Pull it out and sell the motor and trans, buy a 4 cylinder and make a profit.
714-742-5412 Joe
http://www.supermotors.net/getfile/94916/fullsize/pict0062.jpg
Chevy 350 TBI with affordable EFI harness and Computer.
New Aluminum 2 Core Radiator with Ford Taurus Fan and DC Controllers Temp Controller.
Rebuilt Turbo 350 Reverse Manual Valve Body Trans.
Large Heavy Duty Trans. Cooler With 10" Fan Mounted in Bed.
Dual 23 Spline Cases, Fresh Rebuild on Marlin 4.7 case W/Cryo Treated output shaft. Bud built Dual Case Cross member and Skid Plate.
Front And Rear Square Tube Drive-Shafts.
Front Axle has a Lock-rite Locker With 4:10 Gears. Longfield Old Style Treated Birfs, All-Pro Cromo Inner Axles.
85 Rear Axle With A Spool And 4:10 Gears, Sky Manufacturing Rear Disks.
Large Master Cylinder With Residual Valve And Adjustable Proportioning Valve.
Electric Line lock For Brakes, Also an All-Pro T/Case Brake That needs some work.
37" Mickey Thompson Baja Claws on black steel wheels.
Front Has Rancho 4044 Springs, Rear has 63" Chevy 4" lift springs. (No Block)
Shocks Are nothing to write home about. (Junk)
EXO Cage, Front Bumper and Sliders built by Rob Parks AKA Bender.
3" Body Spacer.
Fiberglass Front Fenders, Pinned hood With Small Air-Scoop.
Front and rear Rock Lights, Hella Driving lights.
The pictures Posted were when the cage was new and had not seen the rocks yet, so needless to say it has some rock rash on it. Several test paint patches and a couple of dents.
Body is in good condition, paint sucks, Doors have been stripped of paint. I have about a dozen rattle cans of primer and another dozen or so of Chevy Engine Orange if so desired.
Tube bed could use a Rebuild to match cage tubing. But is functional.
Sliding Rear Window is out and doors are completely disassembled, I have two sets of door windows and all hardware to reinstall either manual or electric windows.
Mazda RX3 seats with 4 point harnesses.
New Reverse Pattern Ratcheting Floor Shifter.
Stewart Warner Gages in original location. Water Temp., Oil Pressure, Trans. Temp, Oil Temp,Volts, Tach And Speedo.
This rig has wheeled Aftershock, Wreckingball, Big Johnson, Claw and Sledge at the Hammers.
I'm sure there is more but I'm crying thinking about all the money I have put in this rig. :crybaby: My loss someone else's gain.
It is street registered and green stickered in Calif. But the street plates have been no opped.
I want $5500 for this rig, pickup in Southern California. If you don't want a V8 Pull it out and sell the motor and trans, buy a 4 cylinder and make a profit.
714-742-5412 Joe