looking for a cross over steering kit for my 76 chevy. it was a shortbed half ton that now has 3/4 ton axles for now anyway looking for a d60. any way i was wondering if there is a cross over steering kit i can get from anywhere? i have 6in lift if that helps also. and if i get one for the d44 will it cross over to the d60 when i get it?

wait till you get a d60 for crossover unless you want waste money getting the passenger side knuckle machined and tapped. the pitman arm will work, but either way you need a 2wd steering box or just a 2wd sector shaft. that is all that will work for both. the drag link may wor may not work.

I am pretty sure that the Dana 60 requires its own crossover steering draglink.
Go to ORD and look at thier crossover steering kits. I know one kit they have is for the 10 bolt/Dana 44.

Whats ORD???

I'll be nice, just click on the link.

http://www.offroaddesign.com/

crossover for d60 and d44 are different. get your d60 then do crossover.

www.wfoconcepts.com 297037 This is a high stear set up I am putting on a dana 60 for my fj40 crappy pic

hey dont watse your money buying cross over stearing, ford comes stock with cross over and a dana 60 is a dana 60 except for pumpkin side, but you can use ford cross over on a chevy, so find a ford and snag it from there. save your self lot of moeny

what year do the fords have crossover steer?

hey dont watse your money buying cross over stearing, ford comes stock with cross over and a dana 60 is a dana 60 except for pumpkin side, but you can use ford cross over on a chevy, so find a ford and snag it from there. save your self lot of moeny

first i have heard of this. not calling you a liar at all. just curious why everyone would buy aftermarket if its readily available. more info please.

You get what you pair for - "garbage in = garbage out"

http://www.reidracing.biz/DANA60.php

If you want it to hold up take a look at this site or ORD's.
Ferd parts on a Chevy truck is Blasphemy in my opinion!

I don't even park my beast near any Ferd! ...might catch some social diease or sumthin. :flipoff2:

My front dana 44 is already machined on that side. the guy I got the axles from must have had cross over. so do i need the whole 2wd steering box or just the arm off it? and how do i get the thing that goes on top of the axle to do it? and the drag link. Im not lookin to spend to much. just figure i might as well do it on here cause i dont know when im getting the dana 60. got to finish my 454 first

three links have been posted so far try going to the sites and reading. do a little research. google crossover steering. look in the tech section where it walks you through crossover. no one is going to come do it for you.

http://coloradok5.com/crossoversteering.shtml

there is a whole guide to build your own

you do require a 2wd steering box, and for the 44 you do need to have it drilled and taped, i just bought a 44 and 14 bolt and i was hoping to do it until i read the article.

with a d 60 i think the article says that there is already a drilled and taped where it would just bolt right in..

looking for a cross over steering kit for my 76 chevy. it was a shortbed half ton that now has 3/4 ton axles for now anyway looking for a d60. any way i was wondering if there is a cross over steering kit i can get from anywhere? i have 6in lift if that helps also. and if i get one for the d44 will it cross over to the d60 when i get it?

Whats ORD???

My front dana 44 is already machined on that side. the guy I got the axles from must have had cross over. so do i need the whole 2wd steering box or just the arm off it? and how do i get the thing that goes on top of the axle to do it? and the drag link. Im not lookin to spend to much. just figure i might as well do it on here cause i dont know when im getting the dana 60. got to finish my 454 first

How many names do you have?

1) buy a set of highsteer arms.
2) buy 2wd steering box
3) have draglink made
4) wheel the piss out of it

Just The Two The Joe4x4Randall One Messed Up So I Made This One