been trying to find some rotors for my 3/4 ton dodge D44 front. I don't really know what the axle came out of or what year it was made so i'm having a tuff time finding parts. The parts stores say dodge used drums up till 75 so i guess its newer than that and it came with flat tops on both sides so i guess it's older than 80. And the parts stores give me the option or HD brakes, 3500 pound axle and 4500 pound axle. And they say i can get a rotor, rotor and hub or just the hub. i know i need the rotor and from what i can tell the hub is press onto the rotor. really i just need to know what the axle came out of and whether its a 3500 or 4500 pound axle.
i found these numbers on it
to the right of the diff cover 44-8e
to the left of cover 620121r
can someone help me out. i looked on the dana expert website but i guess niether of those numbers are the bill of materials numbers.

I bet thet 44-8E is really a 44-8F also sounds like a 75-79 fulltime front axle and I would bet it is the 3500lb axle.. I think the 4500 lb axles were 60's..

It has locking hubs on it but from further searching i would agree that its the 3500 pound axle cause apparently dodge put 60's in some 3/4 tons with the big ass diesels. gonna try the autozone ones
thanks

ok, i have ordered and recieved both of the rotors that autozone had for a 79 3.4 ton dodge truck. they were both wrong. the 3500 pound axles hub hole was WAY to samll and the 4500's was about a 1/4 inch to small and wasn't as tall as my stock one. i called the stealership and they don't even make rotors for the 70's dodges.
WHAT THE HELL DO I DO ! i pulled these numbers off the rotor
102805
and WFM3
measurements are
12 13/16 across the whole rotor
8 5/16 on the raise part that the hub sits on
5 1/16 where the hub passes through the rotor
and the raised part of the rotor sits 2 1/16 tall
anyone have any ideas on how i can find a new rotor. it would really suck to order carparts.coms rotors or parts americas and wait 2 weeks and them be worng. they list the same options as autozone.
anyone know of a book with the measurements or rotors and part numbers?
i really need some help. big dogs is next weekend and i'd love to make it
thanks

just talked to a different dealer and he says he can get the hub and rotor ass. for 550!!!!!!! he gave me the part number 4089275. all i need is the disk itself. starting to look like i can go get chevy outers for it for the price of one rotor. anyone know somewhere else to get his thing?
thanks

There are differences if you dont ask for the W type dodge. Ill post a pic of it later tonight.

cool, even if you can't get a pic if you could just break out a tape and take some measurements i could tell if its what i need. where did you get it? i have been looking for a 79 w200 which from what i know is the 3/4 ton 4x4 dodge truck in the 70's-80's
thanks

Have you tried looking up on the Dana BOM site?

http://www2.dana.com/Expert/wc.dll?cvsp~demenu~DEMENUA~

BTW, does the hub on that axle look like this?

http://www.tennessee4x4.com/toyota/images/dodge/dodge-10.jpg

i pulled the numbers 620121r from the left of the diff cover on the cast part of the housing, looked it up on the site and couldn't find anything, everything starts with 61. any ideas. where would the BOM number be on the axle.
no it has the internal locking hubs on it,
thanks
keep it coming

This is it. Im gonna use it for my rear disc brake conversion. The D60 rear I have is 30spl & came form a 77/78 F250. The bearing hub will need a slight bit of clearancing around the outer edge to fit inside this hub. let me know if you need a better pic, I know this one is terrible.:beer:
Oh, & it does measure 12 3/4in