Judd
08-06-2007, 05:52 PM
Hello, I have for sale a 1979 Jeep CJ7. I will list the good and the bad. If you have any questions or would like pics please email or message me with your email address and I'll get ya some pics.
THE GOOD:
AMC 360 V8
-fresh black paint on block and accessories
-new parts include: battery, coil, pickup coil in distributor, plugs and plug wires, distributor cap, 1/0 guage battery wires, starter, chrome valve covers, Edelbrock 650 carb, Edelbrock aluminum intake, Edelbrock chrome breather, RV cam, coated exhaust manifolds, dual flowmaster exhaust (inside framerails), Ignition system is a Ford TFI electronic ignition system. This system supplies 40K volts, much more powerful and responsive than the stock breaker system.
T150 Transmission and D20 transfer case
-3 speed trans
-brand new clutch throwout bearing
Axles
-D30 front axle 3.73 gears
-New brake calipers and brake lines through out truck (all new hardlines, front to back and new rear soft line)
-M20 rear axle 3.73 gears
-Moser 1-piece rear axle kit
Electrical
-New EZ Wire wiring harness through entire truck
-All new underhood wiring
-Flush mount tail lights
-Rear mounted back-up light with dash switch
Body
-1991 YJ body
-New poly body mounts
-Aluminum Diamond plate rear corners
-14 guage side plates bolted to body
-Rear bumper with 2" hitch welded to a new rear crossmember
-Big Daddy offroad steering box support
-Frame has been wire wheeled, epoxied, and painted with Rustoleum Hammered paint
-Custom crossmember for transfer case
-New poly gas tank
-Autometer guages, water temp, oil pressure, tach (tach does not work though...)
-Battery cut-off located in the cab on dash
-New dash fabbed from 16 guage steel
- New Corbeau seats mounted on steel tube that is welded to the body and the roll cage
-Brand new side mirrors from 4WD Hardware
-Fabtech spare tire carrier in bed with full size spare
Tires/Wheels/Suspension
-4" spring lift
-Dropped pitman arm
-33x12.50x15 BFG Mud Terrains w/ 75-85% tread
-Wheels, nothing special, see pics
THE BAD
-body has holes in floor and is not in the best shape
-paint is okay, it is Rustoleum enamel and was applied with a roller
-transfer case leaks a little, needs a new gasket on the inspection cover
-rear axle leaks a little, also needs a new gasket on the inspection cover
Jeep was taken down to the frame and rebuilt last winter. Many new parts and lots of hard work were spent to make this jeep what it is. Could use some TLC to clean it up, or just use it as it is. Motor starts easily and runs well, plenty of power.
PRICE: $4000 OBO
Just moved to Connecticut and need both the space this jeep takes up and the money.
Any questions, please ask!
LOCATION: Colchester, CT
THE GOOD:
AMC 360 V8
-fresh black paint on block and accessories
-new parts include: battery, coil, pickup coil in distributor, plugs and plug wires, distributor cap, 1/0 guage battery wires, starter, chrome valve covers, Edelbrock 650 carb, Edelbrock aluminum intake, Edelbrock chrome breather, RV cam, coated exhaust manifolds, dual flowmaster exhaust (inside framerails), Ignition system is a Ford TFI electronic ignition system. This system supplies 40K volts, much more powerful and responsive than the stock breaker system.
T150 Transmission and D20 transfer case
-3 speed trans
-brand new clutch throwout bearing
Axles
-D30 front axle 3.73 gears
-New brake calipers and brake lines through out truck (all new hardlines, front to back and new rear soft line)
-M20 rear axle 3.73 gears
-Moser 1-piece rear axle kit
Electrical
-New EZ Wire wiring harness through entire truck
-All new underhood wiring
-Flush mount tail lights
-Rear mounted back-up light with dash switch
Body
-1991 YJ body
-New poly body mounts
-Aluminum Diamond plate rear corners
-14 guage side plates bolted to body
-Rear bumper with 2" hitch welded to a new rear crossmember
-Big Daddy offroad steering box support
-Frame has been wire wheeled, epoxied, and painted with Rustoleum Hammered paint
-Custom crossmember for transfer case
-New poly gas tank
-Autometer guages, water temp, oil pressure, tach (tach does not work though...)
-Battery cut-off located in the cab on dash
-New dash fabbed from 16 guage steel
- New Corbeau seats mounted on steel tube that is welded to the body and the roll cage
-Brand new side mirrors from 4WD Hardware
-Fabtech spare tire carrier in bed with full size spare
Tires/Wheels/Suspension
-4" spring lift
-Dropped pitman arm
-33x12.50x15 BFG Mud Terrains w/ 75-85% tread
-Wheels, nothing special, see pics
THE BAD
-body has holes in floor and is not in the best shape
-paint is okay, it is Rustoleum enamel and was applied with a roller
-transfer case leaks a little, needs a new gasket on the inspection cover
-rear axle leaks a little, also needs a new gasket on the inspection cover
Jeep was taken down to the frame and rebuilt last winter. Many new parts and lots of hard work were spent to make this jeep what it is. Could use some TLC to clean it up, or just use it as it is. Motor starts easily and runs well, plenty of power.
PRICE: $4000 OBO
Just moved to Connecticut and need both the space this jeep takes up and the money.
Any questions, please ask!
LOCATION: Colchester, CT