I am almost done ! ! ! ! ! ! Just finish up loose ends here and there.



http://i23.photobucket.com/albums/b367/scooter141/ON_JEEP2copy.jpg



http://i23.photobucket.com/albums/b367/scooter141/on_jeep4copy.jpg




http://i23.photobucket.com/albums/b367/scooter141/on_jeep3copy.jpg




http://i23.photobucket.com/albums/b367/scooter141/ON_JEEP1copy.jpg

specs?

Looks nice.

+1 on specs.

I just knew jeeps had a purpose:D

Sweet Ride:mr-t:

89 BII.
5.0L non H.O.
C-6 Trans
205 T-Case, Twin stick'd
D-44 High Pinion Front 5.43 gears Detroit Locker
9 inch Rear 5.43 gears Mini Spool
4 wheel disk brakes
Extended Rad arms and Johnny Joints
14 Inch King Airshocks front
Rancho 9000 rear. (ran out of time to 4 link rear)
Hand Made headers
37X13X15 Boggers

Any other Questions, let me know.

Got a build thread, or any pics of it in progress???

Looks good!

nice, that's how I'd like to build my BII...

First DAY.......

http://i23.photobucket.com/albums/b367/scooter141/firstgotit.jpg


Interior.

http://i23.photobucket.com/albums/b367/scooter141/interior.jpg


Drivetrain gone....

http://i23.photobucket.com/albums/b367/scooter141/11-13-2006-2.jpg


MY dummy engine.

http://i23.photobucket.com/albums/b367/scooter141/DSCF0016.jpg


THE engine.

http://i23.photobucket.com/albums/b367/scooter141/Motordummy.jpg


Axle is in! !

http://i23.photobucket.com/albums/b367/scooter141/DSCF0003.jpg


Side veiw of BII with Axles in.

http://i23.photobucket.com/albums/b367/scooter141/DSCF0003-1.jpg

Whole thing.

http://i23.photobucket.com/albums/b367/scooter141/DSCF0006.jpg

Radius Arm.

http://i23.photobucket.com/albums/b367/scooter141/July_12_2007.jpg

get a little carried away with the yellow paint, did ya? :laughing:





your RA's look like white rhino's

Yea, I pm'ed him about 50 times before I started my Front suspension. Thats why they look like his, that was kinda what I wanted, so I got advice from him.

Thanks, Todd S.

Oh yea, the yellow paint was free. Dont sweat the color choice man.:D
Wait till you see my Drive Shafts......

did you make your own motor mounts, or buy conversion mounts?

I think I used 1986 Mustang GT mounts. Put the right on the left, and the left on the right. It worked allright. I had just read horror stories about the swap mounts putting the motor at an odd angle.

at least i got recognition ha! looks good

What are you going to do for recovery/bumpers?



hick

What are you going to do for recovery/bumpers?



hick

I would like to get a Warn 8000# and make some good looking bumpers.

I am taking it on Vacation to SW Colorado after Labor Day weekend. When we get back its on to phase two. Bumpers, two batterys, 4-link rear, Paxton Supercharger, convert it to Mass Air, and other little stuff.


And White Rhino, You get allot of recognition from me. THANKS AGAIN for the info.

What is your wheelbase now, and what is your projected wheelbase when the rear is linked? Thanks.

no problem

how much did you lengthen them? they look way longer than mine, did you plate them like i said? i might be plating them again soon with 3/8s

also truss that front axle you will twist the tubes

If b2s have a 94" wheelbase it sure looks like those radius arms are way over half that. Maybe 50-55" Seems like a serious rock anchor to me.