Just starting to get into these.

5/8" grade 8, thick washers and tall nuts included. 3 3/8" inside for the 14Bff. 8.625" tall. 4.5" of thread.

$13.00 each plus a ride.

Call to order these, We haven't gotten them on the website as of yet. Next couple days.

We'll be adding Dana 60 kits real quick here. Front as well as the rears.

What do you want to see next?

To the top

maybe some rockwell u-bolts?, im having a hard time finding some

maybe some rockwell u-bolts?, im having a hard time finding some

Yep, we can sure get them. Don't have them on the shelf though.

Thanks for all the orders!

Yep, we can sure get them. Don't have them on the shelf though.

How much and would it take long to get them?

How much and would it take long to get them?

I could have them at the shop in a week or less. $13.00 each for 5/8" diam. and $17.00 each for 3/4" diam. All grade 8. Includes washers and tall nuts.

Hey I need a set slightly longer at about 12 to 13 inches.is that possible?

as well as a set of your UD spring plates.

Shipped to 73003?:homer:

toyota ubolts?

toyota ubolts?

Yep, just need your specs. Give me a shout and I'll get you some numbers.

712-479-2251

Top

Top

Btt

Top

btt

Rear set for a sterling 10.25 axle. 5/8" dia. x 8" tall.

Need 2 sets shipped 95012

Rear set for a sterling 10.25 axle. 5/8" dia. x 8" tall.

Need 2 sets shipped 95012

What's the tube diameter on a 10.25" sterling?

quote on 8 large for Dana 60 shipped to 75455 - pm please

quote on 8 large for Dana 60 shipped to 75455 - pm please

8 of the large one on the dana 60?

$13 each plus 13.50 flat rate shipping.

11" dana 60 U bolts and I am also looking for spring plates for a dodge dana 60 front.

went to your site I am intereasted in you anti wrap and truss. for a short wheelbase.

11" dana 60 U bolts and I am also looking for spring plates for a dodge dana 60 front.

went to your site I am intereasted in you anti wrap and truss. for a short wheelbase.

Just give us a call at the shop and we'll get you hooked up:smokin:

I need to buy 8 for a set of Dana 60's that I am putting on a jeep. The rear ones should be fine, but I will need longer ones for the front (since I am having to put the front axles on a perch of 2-3 inches so the original leaf springs will go over the pumpkin).

I need to buy 8 for a set of Dana 60's that I am putting on a jeep. The rear ones should be fine, but I will need longer ones for the front (since I am having to put the front axles on a perch of 2-3 inches so the original leaf springs will go over the pumpkin).



Sorry, missed this one. If ya haven't gotten something sorted out already, call me with your dimensions and I'll help ya get it together.

bump

Sorry, missed this one. If ya haven't gotten something sorted out already, call me with your dimensions and I'll help ya get it together.

Was wondering where the rest of my order is. I received one box with the front perches and u bolts, but still have not got the rest in and it has been a good while. I ordered just the front, but before the order was shipped called and got it changed to the front and rear. Was charged 2 seperate times on my credit card. Just making sure that you haven't forgot about me. Thanks - the fronts look real nice though and like you said won't require any grinding - prefect fit!

Was wondering where the rest of my order is. I received one box with the front perches and u bolts, but still have not got the rest in and it has been a good while. I ordered just the front, but before the order was shipped called and got it changed to the front and rear. Was charged 2 seperate times on my credit card. Just making sure that you haven't forgot about me. Thanks - the fronts look real nice though and like you said won't require any grinding - prefect fit!


Give me a shout on Monday and I'll find out what the delay is.

Was puttting everything together today and had some problems with the u bolts. Perches and plates fit perfectly, but the nuts locked up on the u-bolts. I ran the nuts down to the plate with my fingers and then hand tightened the nuts with a wrench, but they did not hit the spring plate. The nuts locked up on the u-bolts and I had to cut off the two u-bolts (could not even back them off with the air wrench). Seems like there was too much play in the bolts and nuts (maybe not cut deep enough?) The other bolts worked great - so I used the ones from the front to finish the back (need u-blots for the front now). Doubt that this is a common problem as everything else seems to be high quality work. PM sent

PM back your way.

Bump

You have a PM!

I need a standard set of u bolts for a 79 Dodge Dana 60. Two for the driver side and one for pass. side that fits around the casting at the pumpkin. I have plates and the two bolts that go into the casting. How much to 23111, Va.
Thanks

Start off by saying thanx for making awesome product for me:D
I got your disc break conv, pinion gaurd, diff covers, bushings, on & on.

Will u sell me just the studs on a gm dana 60 front? Quote?

I need a standard set of u bolts for a 79 Dodge Dana 60. Two for the driver side and one for pass. side that fits around the casting at the pumpkin. I have plates and the two bolts that go into the casting. How much to 23111, Va.
Thanks

The three ubolts are $40.50 and 9.85 for the ride. Call me we'll get them on the way.

Addict, we can get the studs. They are kinda spendy. We've been using bolts for the longest time without any problems. We can hook you up with either. Or hit up your local hardware store and save some shipping. 5/8"x13 TPI and whatever length you need for you combination of course. Maybe we spoke about this on the phone already.

I got in touch with u about the dana sixty studs. Thanx again!

Have a chevy 44 and keep bending the stock u-bolts ( ya ya if I keep them tight they wouldnt bend :D:D ) and would like to step up one size. I know I can do it with 3 of them but dont know about the larger u bolt. Shipped to 95620


Also need some thick u-bolt top plates. Thks Ken

Order Leaf Springs, Coil Springs, Leveling Kits, Add a Leaf, U bolts, Custom Springs and Lift Kits securely online from anywhere in the continental United States. Whether you have a Toyota Tacoma with broken leaf springs or need heavy duty coil springs for your pickup truck. Need to add hauling capacity to your Dodge Ram, want to level the front of your Chevy / GMC 2500, an eight inch lift kit for your SuperDuty or need some new automotive leaf springs for your classic car or even your Dumptruck then General Spring has what you need.
__________________________________________________
health care jobs which pay more (http://www.mhadegree.com/5-healthcare-jobs-which-pay-more-than-you-think/)
East Setauket Med Spa (http://eastsetauketmedspa.com)

We can also get the custom odd ball stuff.

ubolts for the 14bff and some for the dana 60 in stock.

What other sizes do you want us to carry, we'll get them in for you.