|
: pics of DRW chevy axles w/H1 rims?? jeepcj3a 12-19-2007, 01:47 PM looking for pictures of chevy 60/14 bolt 1 ton DRW axles with stock H1 rims. thinking about running this set up on a toyota truck and dont know if it will be too wide. jesster 12-19-2007, 01:59 PM IMO, an uncut DRW 60 even with H1's is too wide. I am running a GM DRW 60 cut 8" on the long side. Measured width with H1 wheels and 36x12.50 tires is about 78" to the outside of the tires. I think there was a thread about this a few weeks ago if you search around for it... 3vze 12-19-2007, 05:50 PM Heres my DRW 14/60 with stock H1's http://lh4.google.com/fiveota/Rt8FT7Jt3vI/AAAAAAAAA0k/miWuRCmA9eI/side.jpg?imgmax=512 EDIT: heres a lame poser shot but it shows that a 12.5 will stuff http://lh4.google.com/fiveota/Rt8Fg7Jt3xI/AAAAAAAAA00/gtXwRgwUrW8/stump1.jpg?imgmax=512 trkklr77 12-19-2007, 05:51 PM you didnt look very hard did you? a drw d60 with h1 is -/+ 1" of the track width of a srw. looks like our rims came from the same source at some point !haha! jeepcj3a 12-19-2007, 06:20 PM obviously didnt look hard enough. Thanks for taking the time to post up. have yall ever had a problem damaging the hubs in the back? trkklr77 12-19-2007, 06:57 PM ?????? jeepcj3a 12-19-2007, 07:04 PM ?????? ive read that on a rear DRW 14 bolt that the hub sticks out and didnt know how far it sticks out and if it ever gets damaged on the trail as some front locking hubs do when there are SRW hubs with stock H1's. trkklr77 12-19-2007, 07:07 PM i have a super long wheel spacer on my rears, the axle flange is 2" below the wms, about as protected as it gets. as for most, i wouldnt think that it would cause any real damage other than shear some bolt heads off. BIG98XJ 12-19-2007, 07:23 PM http://photos-097.ll.facebook.com/photos-ll-sf2p/v141/45/107/71100097/n71100097_31034583_2935.jpg http://photos-097.ll.facebook.com/photos-ll-sf2p/v148/45/107/71100097/n71100097_31093019_6378.jpg jeepcj3a 12-19-2007, 07:27 PM trkklr77 you are running a DRW 14 bolt right? thanks again for your help trkklr77 12-19-2007, 07:30 PM no, srw with spacers. sorry about that, typicaly everyone is worried about the front. 3vze 12-19-2007, 07:42 PM Yea, the problem you run into is when you do H1's with SRW fronts. They do stick out quite a bit. trkklr77 12-20-2007, 08:54 PM the disance the hub sticks out [while yes it sucks] is moot, you cant clear the knuckle arms or the steering arm on the top of the knuckle with stock rims on a srw. 49willys 12-20-2007, 11:21 PM Drw 60/70hd | |