http://www.ballisticfabrication.com/assets/images/ballisticjoint/bj1.jpg

http://www.ballisticfabrication.com/assets/images/BallisticJoint/BJbearings.jpg

$29.99 ea!

http://www.ballisticfabrication.com/263quot-Heavy-Duty-Ballistic-Joint_p_1226.html#

Price on 8 joints and 8 1" weld on studs.

Toddy

Did you need the studded version or just the housings and studs seperate?

For $27.54, would I be getting the 2.63" joint with the stud already welded on?

The studded versions start at $46.54 for pirate members.

whats the weldable width on the 3".................I have 1" 5/8" inside diameter of tube that I have been itching to use with maybe a inner sleeve of..............

2.0", should work great!

What is the pirate 4x4 discount code? I'm looking to order some other stuff as well.

'pirate'

Discount applies to everything we sell!

The studded versions start at $46.54 for pirate members.

:eek:,Oh well, I can get them cheaper localy

Get what? Johnny joints? Just know that these are in an entirely different class then the currie joints.

damn I just checked the O.D of the tube and its 2 and 3/8"..........I am going to have to think about what to do.....




BTW ,I think these are far better than johnny joints and a great price

you guys carry a perch mount type bracket to fit the 3.0 joints into?...thinking about running in in the rear off the frame, with a shackle shooting down from it.....Not sure if you get my idea.....Basiclly an axle perch with a half cut 3.0 diam...

No, but that would be something that could be worked up quite easily..

damn I just checked the O.D of the tube and its 2 and 3/8"..........I am going to have to think about what to do.....




BTW ,I think these are far better than johnny joints and a great price

We have tube adapters for 2.25" OD tube, then use a threaded shank... Or you can do what we do and throw the tube in the mill and machine two flats 3/16" deep on either side of the tube, which is really the easiest way to cope them to 3" as well...

about 2" long flat on the tube?I am going to have to call my buddy with a mill to see if he can handle it.:D thanks for the advice!!!!!!!

The flat only needs to be about .75" along the tube, but needs to be at least .250" deep (assuming you have sufficient wall thickness). Have him cope the tube to 3.0" while he has it all fixtured as well

quote please....a pair of 3.o flex joints shipped to 95832.Thanks.......

PMs responded!

Thanks for the orders!

price on 16 of the 3 inch joint with 1 inch stud

PMs sent!

Price please for:
2 2.63 joints with 5/8" holes and 7/8 LH studs
2 7/8 LH inserts for 1.5" x .250 Wall DOM
2 7/8 LH Jam Nuts
2 2.63 joints with 5/8" holes and 7/8 RH studs
2 7/8 RH inserts for 1.5" x .250 Wall DOM
2 7/8 RH Jam Nuts
2 2.63 joints with 5/8" holes and 1 1/4 LH studs
2 1 1/4 LH inserts for 2" x .250 Wall DOM
2 1 1/4 LH Jam Nuts
2 2.63 joints with 5/8" holes and 1 1/4 RH studs
2 1 1/4 RH inserts for 2" x .250 Wall DOM
2 1 1/4 RH Jam Nuts
1 Tool for above.
Shipped to 60423 (Business)

I'll get to that one in the morning...

PM sent!

What is the degrees of misalignment that the smaller joints can handle compared to the 3.0 ones THANKS

i need 16 of the 3" joints. do you have the spanner tool for the 3"? i didnt see it on the site. Also i need a bunch of you link mounts. Can i get them in 3/8" plate the with 3" joint width and 3/4 holes for these joints? send me a pm, please.

Yes you can get all of those parts, but you will need to call for custom pricing.

We have 3" spanners, but do not have them listed because they are in tight supply right now.

I'll get back to you on misalignment, but both are very comparable to eachother.

I just checked this out your site. You have a bunch of good stuff. Could I get a price for two of each with a total and what the tinsel strength is on this heim.
XM-16 1.25" w/ 1.0" ball CrMo rod end w/ kevlar liner with high misalignment spacers, jam nut, and tube adapter.
Shipped to 94947.
I am shopping for rod ends for the front of my dodge diesel as I just broke a stock control arm.
Thanks

PMs sent, thanks

Can I weld the 2.63" joint to a 2-1/4" OD tube?

No,but I can post pics of how we use the 3.0" joints in house... but you'll need a mill. The housing is 2.0" wide on the 3.0" joint and only 1.875 on the 2.63" joints.

sent you a pm

So, with a 2.63 joint, direct weld to the tube, the maximum tube OD should be 1-1/2" without modifying the tube? thanks!

No, you could use 1.75" OD tube as well.

Just placed over $500.00 order, thanks!

Thank you!

Thanks for the orders! We have a machine dedicated to just running Ballistic joints because they are moving so quickly!

I just ordered almost $800 of stuff last week including 8 of the new joints. Is there going to be a long wait for the joints?

Can't wait for my new toys to show up.:smokin:

I'll check on your order but ship times on joints are very good these days since we manufacture 100% of the joint in house. Your order may be held up be some other part though, but I'll check and see.

Just recieved my 16 2.63 joints, look good, but you may wanna think about threading for the retainer nut after the setscrew hole is tapped, mine have a nasty burr in them. My only complaint is my email I sent a day after I ordered, requesting you to add a spanner tool to my order, never got answered. And its not worth the shipping just for that. It is my fault for forgetting to order it with the joints, but i would expect a reply anyway.

I'll get back to you on misalignment, but both are very comparable to eachother.

Well what did you find out???

Just recieved my 16 2.63 joints, look good, but you may wanna think about threading for the retainer nut after the setscrew hole is tapped, mine have a nasty burr in them. My only complaint is my email I sent a day after I ordered, requesting you to add a spanner tool to my order, never got answered. And its not worth the shipping just for that. It is my fault for forgetting to order it with the joints, but i would expect a reply anyway.


I would have no problem sending out a spanner at no shipping cost to you. Sorry about the email, some if not most have been getting filtered lately, and we have recently fixed it. Thanks -Jeff

within the next month im looking for 8 joints ....

please quote for :

qty 8) 2.63" joint, RH thread, 1.25 x 12TPI, 5/8 thru-hole
qty 8) jam nuts 1.25 x 12TPI


and seperately:
qty 8) 3.0" joint, RH thread, 1.25 x 12TPI, 3/4" thru-hole
qty 8) jam nuts 1.25 x 12TPI

also, so you have any strength numbers to compare the two?? (i know the strength between the 3/4 and 5/8 bolts ... wondering about the housing strength

what is the total thread engagement length on the studs?? i need to know how far to tap my links ... thanks.

PMs sent, thanks for the orders!

Jeff

PMs sent, thanks!

8 3" with 1.25 threads ??

do you make them with a 7/8 or 1" hole?

thanks

No we do not, quote sent via PM

Thanks -Jeff

What is the width of the 2.63 joint? I mean the width where the bolt goes through. Is it 2.63? or is that the width of the can?

I also need a perch style mount for the joint to sit in. Maybe with a 3 inch flat base. I want to use this as a mount for an anti-wrap bar. I will bolt a shackle to the joint, and the other end of the shackle will be a bushing at the end of the wrap bar which goes to the axle.

So i need pricing on the small joint, and a perch mount.

Thanks,
Neal.

What is the width of the 2.63 joint? I mean the width where the bolt goes through. Is it 2.63? or is that the width of the can?

I also need a perch style mount for the joint to sit in. Maybe with a 3 inch flat base. I want to use this as a mount for an anti-wrap bar. I will bolt a shackle to the joint, and the other end of the shackle will be a bushing at the end of the wrap bar which goes to the axle.

So i need pricing on the small joint, and a perch mount.

Thanks,
Neal.

Just whipped this up, is this what you're looking for?

https://ballisticfabrication.3dcartstores.com/assets/images/brackets/linksuspensionbrackets/flexframebracket.jpg

Thanks for the orders!

Thanks again!

How much for the following shipped to 94521?

2 - 2.63" Flex Joints 9/16 hole w/ Stud (3/4-16 RH Thread)- Zinc plated
4 - 2.63" Flex Joints 9/16 hole w/ Stud (3/4-16 LH Thread) - Zinc plated
1 - 2.63" Spanner Tool

What's the bolt hole size for these, 9/16? 2.5" Poly Bushing w/ Stud (3/4-16 RH Thread)

PM sent, the bushing bore with the sleve installed is 9/16". Thanks - Jeff

Thanks for the orders!

quote on the following please:

2-3 inch joints,
4-3 inch joints with 1 1/4" studs, jamb nuts, 2 inserts for 2.25" od, 1.5" id tubing, 2 inserts for 2" od, 1.5" id tubing

shipped to 39110

thanks

Thanks!

Can I get a quote on 2 of your 2.63" joints with welded stud?

Also, how about a pair of the 3" joints for comparison's sake.

Thanks!

PMs sent, sorry that one took a while, I've been out sick for about a week now but I'm coming around now I think...

Price Quote shipped to 94303 please;

#8 7/8-14 tpi billet studs (right hand studs, 2.63 cope notch)

#8 7/8-14 tpi billet studs (left hand studs, 2.63 cope notch)

#4 7/8-14 tpi tube ends, 1.0 id w/ 1.5 od (right hand threads)

#4 7/8-14 tpi tube ends, 1.0 id w/ 1.5 od (left hand threads)


Can you do custom order tube end sizes?

I need;

#4 7/8-14 tpi tube ends, 1.0 id w/ 2.0 od (right hand threads)

#4 7/8-14 tpi tube ends, 1.0 id w/ 2.0 od (left hand threads)

Were running that size of stock this week so now might be a good time to place that custom order!

PM sent with pricing. Thanks

Can I get a quote on 2 of your 2.63" joints with welded stud?

thanks

Thanks for the orders!

Already got my answer via email. thx

tt

PM sent, thanks for the orders

can I get a price on :

4 - 2.63" joints with 1" threads

shipped to 37338

PMs sent


Both sizes in stock and ready to ship!

Over 1,000 pcs in stock today, going fast!

PMs responded, thanks for the orders!

In stock and ready to ship!

Thanks for the orders!

1,000 in stock and ready to ship as of yesterday

8 Ballistic Joints shipped 40475

8 - 2.63 joints with studs, weld inserts and jam nuts to 32539

Both PMs sent, thanks!

I have a YJwith a WARN XCL suspension. I am going to straetch the wheel base just two inches by putting rebuildable joints on the four links of the axle part of the four link suapension.
I can fit the small 2,63 only and will need some threaded adaptors to fit inside the arm tube. Can you supply them?
Thanks
ed

Can I get a price on 2 Ultra Duty Ballistic Joints with the 1.25" threaded stud welded on, zinc plated and shipping to 95129? Also is there any kind of warranty against breakage on these joints? Thanks!

Sam

price check:

XM-16 - 4 right hand
XM-14 - 3 left hand
1.25 jam nut - 4 right and 4 left
7/8 jam nut - 3 right and 3 left
2.63 HD Joint (7/8 welded on shank, 5/8 bore) - 3 right
3.0 Joint (1.25 welded on shank) - 4 left
1.25 bung (1.5 ID and 2.0 OD) 4 left and 4 right
7/8 bung (1.25 ID and 1.75 OD) 3 left and 3 right
1 to 5/8 missalignment - 4
7/8 to 5/8 missalignment - 3

Can I get a 3.0 with the 5/8 bore? If not please add in what I need to make it to 5/8. Thanks

PMs sent, thanks for the opportunity to quote you!

Thanks for the orders!

ttt!

Releasing ver 2.0 of the 3.0" Ultra Duty Ballistic Joint today!!

Releasing ver 2.0 of the 3.0" Ultra Duty Ballistic Joint today!!

whats new with it?

Didn't finish the pics today, but the new ones are shipping. I'll fill you in tomorrow with pics - Jeff

sweet thanks, i need some new joints... is there a static load rating on these? or have they not been tested?

thanks

No testing as of yet, we have a hard time investing in tests like that when the real use is nearly 100% dynamically loaded.

P.M. Sent

Can I get a price for 4 normal joints shipped to 95620, non studded

http://www.ballisticfabrication.com/assets/images/flexjoint/3bjstud1.jpg

http://www.ballisticfabrication.com/assets/images/flexjoint/3BJstud2.jpg

Look at the wall thickness on that baby :grinpimp:

http://www.ballisticfabrication.com/assets/images/flexjoint/flexjoint4.jpg

http://www.ballisticfabrication.com/assets/images/flexjoint/3bj3.jpg

http://www.ballisticfabrication.com/assets/images/flexjoint/3BJ1.jpg

Almost 1.5 lbs of added material, SAME PRICE!

$39.99 unwelded
$60.00 with threaded shank

Don't forget the 'pirate' discount!

The Massive 3.0" rebuildable Ultra Duty BALLISTIC joint exclusively from Ballistic Fabrication is built to withstand extreme punishment. It's extra large 3/4" bore (bolt hole) is large enough to handle heavy torque, while the huge 3.0" diameter .320" wall housing accomodates over 25 degrees of misalignment both ways. The giant 2" ball distubutes the forces over a larger surface area and translates into a better ride and longer life as well as superior strength. The BALLISTIC joint features solid billet Nylatron GS races that won't deform under load and provides a smooth bearing surface for a noise free ride. Fully greasable and rebuildable. Sold individually.

Choose from a 7/8" 14 tpi, 1.0" 14 tpi. or 1.25 12 tpi stud available in both right or left hand thread.

http://www.ballisticfabrication.com/Ballistic-Joints_c_12-1-0.html

Good job Jeff!

http://www.ballisticfabrication.com/assets/images/flexjoint/3BJ1.jpg

thanks! :p

Never got a price




Can I get a price for 4 normal joints shipped to 95620, non studded

Can I get a price for 4 normal joints shipped to 95620, non studded

Are you asking about the 2.63" joints?

Jeff

Are you asking about the 2.63" joints?

Jeff

Yes sorry about that :rolleyes::rolleyes:

Thanks, we sold alot of these today:D and we still have plenty in stock. Tomorrow we start the manufacturing process again :p

Thks for the PM. Will put order in the next day or so. Do you have these in stock, wife and kids are getting them for me for xmas :grinpimp::grinpimp:

Yes, every size in stock right now, and we're machining overtime to make sure it stays that way. Thanks - Jeff

Just ordered 4 from your website.

Dera sirs:
I need for my WARN XCL equipped Yj the following:

FOUR Ballistic Fabrication Classic Sticker $0.00 $0.00

FOUR 2.63" Heavy Duty Ballistic Joint with threaded shanks as long as possible. Bore (bolt hole size): 9/16"

ONE Spanner tool for Ballistic Joints Joint Size: 2.63'' Ballistic Joint

TWO Ballistic Joint Rebuild kit Ballistic Joint Size: 2.63'' Heavy Duty

can you PM me the total price?
thanks
Ed

Got my 2.63 joints today,

Any tips on putting it together?

Seems simple, But when I went to put it together, The bushing seem real tight. Should I just grease it and press it in.

Just didn't want to mess it up.

Yes, the race should be near press fit by design. Thanks - Jeff

do you have tube adapters to for 1.5 inside square tubing

How well do these seal out water etc?

Also, can I get a PM price for the following:

8 RH 2.63 Ballistic Joints
8 LH 2.63 Ballistic Joints
8 RH Jam nuts
8 LH Jam nuts
4 RH tube adapters for 1.5"x2" DOM
4 LH tube adapters for 1.5"x2" DOM
4 RH tube adapters for 1.5"x2.25" DOM
4 LH tube adapters for 1.5"x2.25" DOM

Shipped to business address at 77845?

Thanks!

do you have tube adapters to for 1.5 inside square tubing

Yes we do

http://www.ballisticfabrication.com/125quot-Square-tube-adapter_p_1557.html

How well do these seal out water etc?

Also, can I get a PM price for the following:

8 RH 2.63 Ballistic Joints
8 LH 2.63 Ballistic Joints
8 RH Jam nuts
8 LH Jam nuts
4 RH tube adapters for 1.5"x2" DOM
4 LH tube adapters for 1.5"x2" DOM
4 RH tube adapters for 1.5"x2.25" DOM
4 LH tube adapters for 1.5"x2.25" DOM

Shipped to business address at 77845?

Thanks!



PM sent

OK,

Is the forged joint and the forged bushing total width 2.65? I saw that the housing was 1.875. I can't tell if there were any dimentions on the pic that was posted of the bracket.


Thanks,
Jason

OK,

Is the forged joint and the forged bushing total width 2.65? I saw that the housing was 1.875. I can't tell if there were any dimentions on the pic that was posted of the bracket.


Thanks,
Jason

The 2.63" mounting width perfectly matches most of our brackets intended to be used with our 2.63" Ballistic Joints.

Correct me if I am wrong but there 2.63 wide. I am sure the rep will chime in.

That is correct, both are 2.63". The 3.0" joints are 3.0" wide. Thanks - Jeff

sent you a pm

I have a question and need some prices

MY question is. i know that people normally use a larger joint for the lower links. So would i need to use a 3" joint on the bottom and 2.63" on the top or would 2.63 work fine both ways???


So i need price for (4) 2.63" joints to 30277

also (2) 2.63" and (2) 3.0" joints to 30277

Thanks
PegLeg

I'll make sure I get to this in the morning, I don't normally follow our older threads now that we have our own forum, but thanks for the inquiry.

Jeff

1.25 12tps studded with tube adapts and jams shipped to 55049 business thanks

Can i get a price for 8 2.63 joints with 5/8 holes