|
njjeep 02-16-2008, 04:13 PM i will be swapping out my stock amc20 and dana 30 for one tons i was wondering what my ground clearance is goin to be with a chevy60 and unshaved 14bolt i currently have 35" baja claws so i know i will prob have to go to 37s thanks 80j5 02-16-2008, 04:20 PM 13 bolt its the only way to go:D shaved down you will have more clearance under the 14 bolt than the 60. ill get a measurment for yah if you must have one:flipoff2: njjeep 02-16-2008, 06:18 PM i guess i will shave it to a 13 bolt. does anyone know the ground clearance of a dana 60 with 35s or 37s? thanks 80j5 02-16-2008, 06:36 PM not a lot :D 80j5 02-16-2008, 06:41 PM 60 is about 6 in from center tube to bottom 14 bolt is about an inch more give or take. 80j5 02-16-2008, 06:45 PM fwiw i had 10 in under my dana 44 with 35's njjeep 02-16-2008, 06:49 PM thanks rockrknockr 02-16-2008, 07:19 PM with those axles i'd think 40's chadburgin 02-16-2008, 08:51 PM with those axles i'd think 40's x2...35s are way to small for a 14bolt or a 60 front for that matter...even one that has been shave IMHO!!! bigcamojeep 02-17-2008, 06:20 AM DON'T LET THIS HAPPEN TO YOU!! 14B shaved with 36" IROK's http://inlinethumb63.webshots.com/38654/1225138456047347444S500x500Q85.jpg (http://rides.webshots.com/photo/1225138456047347444QCAMRo) I'm still running this setup, but only because I have too much wrapped up in it. If I were to do it again, I'd use a built up 9" or something like that chadburgin 02-17-2008, 05:30 PM agreed, Or at least went with a much bigger tire!!! Shaggygto 02-19-2008, 10:25 AM x2 on the 40's seriously, i ran my 14 bolt unshaved with 36's and it drug everywhere. njjeep 02-19-2008, 05:38 PM so 40" tsl's or iroks on stock yj springs in the front and stock xjs in the back. wonder how much i will have to trim the back fender well?LOL SHAGGYGTO btw Im sitting at houston fuel oil on my tug getting ready to get underway and bring the barge to New Orleans Shaggygto 02-19-2008, 06:19 PM Awesome. Tugs are cool man. Tons of power. I'm a subsea engineer for deepwater gulf of mexico. yeah, it'll take some triming i'm sure, but that is exactly the suspension i am looking into now. txdave 02-20-2008, 03:09 PM i guess i will shave it to a 13 bolt. does anyone know the ground clearance of a dana 60 with 35s or 37s? thanks 10.5"under my d60 on 37"S Shaggygto 02-21-2008, 08:27 AM Awesome. Tugs are cool man. Tons of power. I'm a subsea engineer for deepwater gulf of mexico. yeah, it'll take some triming i'm sure, but that is exactly the suspension i am looking into now. Just comp cut the rear. Pirate Joe 09-07-2010, 06:12 PM I know this is old, but I'm going to ask. How does Ballistic Fabs 14b shave kit compare to a D60 in ground clearance? It claims to give 2" more clearance over an unshaved 14b. Think that would be enough to squeeze by with 37s? That would be like running a 41" tire with no shave. -Joe | |