Todd W
06-15-2008, 08:51 PM
$6,000 and you can have the Hypertherm 600 and 4'x4' CNC Plasma Table. The table is nearly new, and I replaced the Y-AXIS pulley and belt, and have them for the X too. The Y belt was replaced because I stretched the belt, and I replaced the pulley while I there. The grates are nearly new, almost no slag on them, the other side is new. Hypertherm 600 comes with fine-cut consumable kit nearly new too as well as a couple other new consumables not in the kit.
I am selling because I've had it since Feb and have not even gone through 1 sheet of steel, and have not had time to dedicate to the machine. Now I`m moving, and it's sitting in storage. Machine and plasma cutter operate fine, I've posted video of it in action and can get more shots and videos.
With the hypertherm 600 you can do 3/8" on the table some users have done 1/2" it's just slow For 16ga adn thinner you can do 150ipm and it's blazing reaking fast
I have ~250 DXF and PCM files I wll GIVE FREE too. They are non (C) files that can not be sold but if you cut the designs you can sell those.
The table has been enclosed on all 4 corners and has 2 13" holes on the front for an exhaust system. (Exhaust fans not included) I will throw in my water table, it sits under the grates and catches hot parts and large sparks. The water table is on casters so you can slide it out and take parts or slag out if you need it. Water evaporates faster than it needs cleaning so you can stick a hose in it and fill`r up easy too. I'd suggest an exhaust fan or two if you plan to run in a small shop/garage, northern has them reasonable price too.
Also included are:
I have plasmacam cd software, plasmacam manual, hypertherm manual, and a bunch of documents that I printed to make it easier to understand, use, and setup. ALso included are my hand written notes You can go from having it in parts in your truck to running in <1/2 day. I assembled it from the manual very easily. PLug and Play.
You also get the Gateway Computer, Monitor, and equipment to run.
This is 100% package ready to CNC Cut and go.
-Todd
I am selling because I've had it since Feb and have not even gone through 1 sheet of steel, and have not had time to dedicate to the machine. Now I`m moving, and it's sitting in storage. Machine and plasma cutter operate fine, I've posted video of it in action and can get more shots and videos.
With the hypertherm 600 you can do 3/8" on the table some users have done 1/2" it's just slow For 16ga adn thinner you can do 150ipm and it's blazing reaking fast
I have ~250 DXF and PCM files I wll GIVE FREE too. They are non (C) files that can not be sold but if you cut the designs you can sell those.
The table has been enclosed on all 4 corners and has 2 13" holes on the front for an exhaust system. (Exhaust fans not included) I will throw in my water table, it sits under the grates and catches hot parts and large sparks. The water table is on casters so you can slide it out and take parts or slag out if you need it. Water evaporates faster than it needs cleaning so you can stick a hose in it and fill`r up easy too. I'd suggest an exhaust fan or two if you plan to run in a small shop/garage, northern has them reasonable price too.
Also included are:
I have plasmacam cd software, plasmacam manual, hypertherm manual, and a bunch of documents that I printed to make it easier to understand, use, and setup. ALso included are my hand written notes You can go from having it in parts in your truck to running in <1/2 day. I assembled it from the manual very easily. PLug and Play.
You also get the Gateway Computer, Monitor, and equipment to run.
This is 100% package ready to CNC Cut and go.
-Todd