Pook
08-20-2008, 12:26 AM
Whats everyone running? how are they holding up?
|
Pook 08-20-2008, 12:26 AM Whats everyone running? how are they holding up? mtbrjon 08-20-2008, 04:28 AM Whats everyone running? how are they holding up? TG (narrow axle). Just fine. Previously broke 4 stock shafts. benttoy 08-20-2008, 07:37 AM Stock narrow 5 years no issues Brian Ellinger 08-20-2008, 09:25 AM stock right now, Marlin's are sitting with bearings on them, VERY nice pieces coming from Alloy, sI I know what they'll take! Pook 08-20-2008, 11:30 AM TG (narrow axle). Just fine. Previously broke 4 stock shafts. We haven't had the same luck with them. :( Anyone running the polyperformance shafts? mtbrjon 08-20-2008, 12:41 PM We haven't had the same luck with them. :( Narrrow or IFS? Pook 08-20-2008, 01:38 PM narrrow Or Ifs? Ifs GETTINTHERETOY 08-20-2008, 03:12 PM We haven't had the same luck with them. :( Anyone running the polyperformance shafts? I've got the poly shafts in mine. No problems in two wheeling seasons and a few comps. They were in it when I bought it from Tim Florian so I am not sure how long they had been in before I got it. So far so good though. Irish Style 08-20-2008, 04:54 PM Anyone running the polyperformance shafts? I think I might be running Poly's. D-Toy could probably tell you for sure. What ever they are, they hold up well. Other then the housings, they are the only things south of the driveshafts that I haven't been able to break yet. Air Ride 08-20-2008, 05:17 PM I think I might be running Poly's. D-Toy could probably tell you for sure. What ever they are, they hold up well. Other then the housings, they are the only things south of the driveshafts that I haven't been able to break yet. I think they were from Poly. Poly had a great deal on narrow axles a little while ago. mtbrjon 08-20-2008, 05:26 PM Ifs Hmmm wonder if that makes a difference as mine are the short shafts? I did buy a couple sets of the short Polys now that I think about it and never had a problem with those either. Pook 08-20-2008, 05:49 PM We should have a new turning contest to see if all you guys running narrow diffs out turn mine. Curious to see. azyota 08-20-2008, 06:51 PM I was running the Poly shafts. No problems. Brian Ellinger 08-20-2008, 09:35 PM We should have a new turning contest to see if all you guys running narrow diffs out turn mine. Curious to see. :laughing: Thats just mean! Pook 08-20-2008, 10:31 PM :laughing: Thats just mean! I'm thinking I'd rather have the IFS width with the courses we ran this year on the west coast... :D mtbrjon 08-21-2008, 04:15 AM I may not out turn you but I have 1.5" more room to work on both sides of the rear of my car and every comp I use that space to my advantage.:D Oh and I have the 40Deg Longs and steering setup properly so i'll probably out turn you too.:laughing: benttoy 08-21-2008, 05:57 AM I may not out turn you but I have 1.5" more room to work on both sides of the rear of my car and every comp I use that space to my advantage.:D Oh and I have the 40Deg Longs and steering setup properly so i'll probably out turn you too.:laughing: No way Pook has rear disconnect:laughing::laughing: Stealthrunner 08-21-2008, 06:03 AM some cromos out of zags old buggy....this one.. Pook 08-21-2008, 09:16 AM I may not out turn you but I have 1.5" more room to work on both sides of the rear of my car and every comp I use that space to my advantage.:D Oh and I have the 40Deg Longs and steering setup properly so i'll probably out turn you too.:laughing: Stock width front diff? If so I doubt it :flipoff2: mtbrjon 08-21-2008, 12:11 PM Stock width front diff? If so I doubt it :flipoff2: What do you have tractor front end with the wheels 6" apart? Pook 08-21-2008, 12:28 PM I had Bobby Machine down some 60 birfs till they fit in the knuckle balls. :p Jeep07 08-21-2008, 10:02 PM I run Poly's chromo narrow rear shafts. Work fine and not had an issue at all. | |