|
: arb help YotaCrawler 08-03-2002, 04:20 PM I was instaling the brass fitting that goes into the housing and overtigend it... so how do i get it out, cause the brass line is still screwed in from underneth and i cant get a wrench on it. thanks in advance. PAt sarge 08-03-2002, 05:26 PM did you strip the threads? You might want to pull out the third member and fix it on the bench{ its brass so you dont stip the threads on the third member} its not that hard to change the line, better now then on the trail?:D SeaBass44 08-03-2002, 06:35 PM Originally posted by sarge did you strip the threads? You might want to pull out the third member and fix it on the bench read sig, he has a 44/60:flipoff2: YotaCrawler 08-03-2002, 07:20 PM Gee seabass, im glad ya noticed:flipoff2: ! what happened is the fitting that screws in the housing broke on the top. So WHAT DO I DO??? PAt Oh, I have no third, if I pull the carrier it will dangel from the brass line. YotaCrawler 08-03-2002, 07:20 PM Gee seabass, im glad ya noticed:flipoff2: ! what happened is the fitting that screws in the housing broke on the top. So WHAT DO I DO??? PAt Oh, I have no third, if I pull the carrier it will dangel from the brass line. YotaCrawler 08-03-2002, 07:20 PM Gee seabass, im glad ya noticed:flipoff2: ! what happened is the fitting that screws in the housing broke on the top. So WHAT DO I DO??? PAt Oh, I have no third, if I pull the carrier it will dangel from the brass line. SeaBass44 08-03-2002, 07:53 PM I don't know TRIPPLE POSTER:flipoff2: I would need to see that one. YotaCrawler 08-03-2002, 07:56 PM What the FAWK, what it do that????????? I only cliked submit 1 time. oh i'll be up your way on the 12th. PAt SeaBass44 08-03-2002, 08:00 PM Originally posted by YotaCrawler What the FAWK, what it do that????????? I only cliked submit 1 time. oh i'll be up your way on the 12th. PAt the bb is fucked up the last month or so.... OOP'S 08-03-2002, 08:07 PM When I screwed on my Toyota rearend I pulled the drop out, took the line off the fitting and used a ez-out to get the piece out. Take the cover off, unscrew the air tube and take the fitting out and screw a new one in. I had enough extra tube that I cut it off and put a new ferrel on the air tube!!:D techierob 08-03-2002, 09:01 PM Also it sounds to me like your installers put the brass air line up through the housing instead of through the third member. Now is the time to put it right. drill and tap a new hole and weld shut the old. The bastards that did mine did the same thing. IM LIKE DUDE!! its not a CHEVY!! the 3rd memeber is seperate from the housing. so should the air line. :mad: YotaCrawler 08-03-2002, 09:32 PM Ok, i dont know if you guys understand my set up, i have a dana 60 rear and a dana revese cut 44 in the front, i broke the fitting in the front, the air line is supposed to be on the housing. I can not just take the brass line off because there in not enough head sticking out. Thnaks for tryin to help though. PAt Wilson 08-03-2002, 09:39 PM I have a d44 w/ an arb too, I would try what OOP's said. The brass line should thread out, once you pull the cover, depending on where you ran teh fitting through the housing, with that done, an ez out should do the trick OOP'S 08-03-2002, 09:50 PM Originally posted by YotaCrawler Ok, i dont know if you guys understand my set up, i have a dana 60 rear and a dana revese cut 44 in the front, i broke the fitting in the front, the air line is supposed to be on the housing. I can not just take the brass line off because there in not enough head sticking out. Thnaks for tryin to help though. PAt The fitting that the inside air tube screws to is like a nipple that screws in from the outside, you have to get the the small tube disconnected from the nipple in order to be able to unscrew the nipple out of the housing. YotaCrawler 08-04-2002, 12:48 AM OOP'S, I know what your sayin but I cant get the "nipple" on the bottom off because there is not enough sticking out to grab on to. THANKS for continuing to try to help!! PAt r77toy 08-04-2002, 10:41 AM Pound an allen wrench in the hole and unscrew it. YotaCrawler 08-04-2002, 10:58 AM huh, I may try the allen wrench on it. PAt THANKS sarge 08-04-2002, 01:02 PM what the hell does this have to do with a toyota:confused: try general 4x4 talk I bet more guys will respond and under stand a dana 44:flipoff2: YotaCrawler 08-04-2002, 03:51 PM I got a toyota body, THATS WHAT:flipoff2: :flipoff2: .... PAt dknightd 08-04-2002, 05:34 PM I'd call ARB. While you are ordering replacment parts (I'd order two of everything so you have a set a trail spares as well), ask them for advise on how to get the broken piece out. I'm sure they have probably run into this before... Sorry, I'm not familiar with how an arb goes into a 44. YotaCrawler 08-04-2002, 09:44 PM thats prolly what i'll do. thanks PAt | |