hey, have some trouble with my D60's .

called the shop where i bought them for new one's and he told me he can't get any of these any more.

anybody any tips where i can find 2 or 3 new one's ??


http://www.offroadterror.be/photos/vanalles/U3Wvc1VH9n4zr13u.jpg

http://www.offroadterror.be/photos/vanalles/5UA61tSuubl2kI5X.jpg

http://www.offroadterror.be/photos/vanalles/Zj7X6fSS8H1V5XwZ.jpg

http://www.offroadterror.be/photos/vanalles/g8rjjtcyE27PStTX.jpg

looks a lot like my 2000 Dodge Ram 2500 CTD front unit bearing...

might compare to one of those... mine of course are 8 lug though...

Can you post pictures of the axle? Maybe swap out your knuckles and run a spindle hub setup??

Looks like a 1/2 ton dodge unit bearing.

Why not use Teraflex Spindle Adapter part no. 3001137. That you you can use a D60 fill float spindle and hub instead along with 35 spline outers.

Why not use Teraflex Spindle Adapter part no. 3001137. That you you can use a D60 fill float spindle and hub instead along with 35 spline outers.



Because he could not keep his 5x4.5 lug pattern going to the full floater hub assembly.


Those are Teraflex's copy/version of the stock dodge 2000era unit bearings.

you can get new bearings for them, get the numbers off the bearings you have. should be around $100 for new bearings

how can i get new bearings in, they are fixt mounted in the rest so how can i mount them back in ?

http://www.offroadterror.be/photos/vanalles/aZqcs1FKVfpGl3jW.jpg

http://www.offroadterror.be/photos/vanalles/CFaL2vTS45EbrJys.jpg

http://www.offroadterror.be/photos/vanalles/iKTDcThIJDWgQWfs.jpg

have you tried calling terra?

you already have them appart, remove the race and bearings and replace. the numbers are on the bearing and race

http://www.offroadterror.be/photos/vanalles/iKTDcThIJDWgQWfs.jpg

Are you sure on that 35 spline ? My Tera junk is 33 spline. Not that it really matters. As far as I know they stopped making the unit bearings. But please
someone tell me I'm wrong.

looks a lot like my 2000 Dodge Ram 2500 CTD front unit bearing...

might compare to one of those... mine of course are 8 lug though...

Are you sure on that 35 spline ? My Tera junk is 33 spline. Not that it really matters. As far as I know they stopped making the unit bearings. But please
someone tell me I'm wrong.

I'm pretty sure my dodge unit bearings are 33 spline...

I'm pretty sure my dodge unit bearings are 33 spline...

They are. But the bolt pattern is wrong. If mine go bad I was planing on just pressing my old hub into a 3/4 ton unit bearing. I'm sure tera isn,t making
their own unit bearing. they press a hub in that has the keep pattern.

Well one of mine just went bad.... Doing research I can get the entire hub / bearing assembly off a Dodge 2500 94'-02. Problem is I do not trust pulling the outer bearing off the hub safe without ruining it. I cant seem to find just the bearings to where I could just press my hub into it.

Tera does not make them nor do they know the exact part #'s for the bearings that is used inside of it.

They are easy to press apart but one bearing will stay in the assembly and the other will come out on the hub

Ideas??

i bought my new one's from james @ james@jeepersandcreepers.com , don't know what type it was but they fit

Have an e-mail out to him.
My bearing assembly is good to where if I had the bearings and seals I could just put them in there or if I could find just the assembly and press my hub into it.

Are Branik or Solid axle out of the question?

Are Branik or Solid axle out of the question?

I will ask but they are into f450 stuff. Might be able to pull the hub out safe so I can put my hub in.

kinda looks like they pressed out the old lug studs and redrilled tehm for 5x4.5, i think the dodge ones are 5.5.5