Horsepwer

[GLADIATORFAB]

How much horsepower can toyota v6 axle with 30 spline take with out problems,
ftoy 35

[Brian Ellinger]

How much horsepower can toyota v6 axle with 30 spline take with out problems,
ftoy 35

weight of vehicle?
tire size?

[GLADIATORFAB]

37 tires 3500lbs dual box 228 4.7

[Brian Ellinger]

37 tires 3500lbs dual box 228 4.7

You driving? ~50. :D

Most other folks ~200. :p :D

[desertoy]

You driving? ~50. :D

Most other folks ~200. :p :D


Agreed :flipoff2:

Actually, Mustard Dog runs a Toy rear behind his SB Chevy with no problems. It's not more than 300 hp though.

[MT4Runner]

Lots of people driving around "Chevotas" with 350's...probably unlocked, but still 33's-35's.

Lots of people running 4.3's, locked, 35's-37's.




Still....seems like the FToy crew is more likely to need Chromo rear upgrades than the general Toy population with lockers/gears/22re's/37's!!!

It seems that people generally have more problem with R&P breakage than with shaft failure.

[GLADIATORFAB]

What is mustard dogs rig weight

[desertoy]

I am guessing at 3300-3500lbs. He has a 4cyl 3rd member also.

[Brian Ellinger]

I am guessing at 3300-3500lbs. He has a 4cyl 3rd member also.

I swear I saw v6 rear, and fj60 (looks like an overgrown 4cyl 3rd) in front. :confused:

[desertoy]

He has an FJ-40 front and a toyota 8" 4cyl in the rear.

[ToolBox Guy]

Here is a "Sneek Peak" at my new "Horsepower" for KOH '09!

[GLADIATORFAB]

How much ?????

[ToolBox Guy]

How much ?????












Not going to guarantee anything, but the motor guy is saying that he will tweak it until I put 200 hp to the ground.
I have a rear wheel dyno around the corner from my shop, so I will check it out and post an update.

[splasher]

What about front digs?

Safe with Longs and 37" tires?

[MT4Runner]

Here is a "Sneek Peak" at my new "Horsepower" for KOH '09!

What Chassis #?

[EarlKann]

What Chassis #?



Ummmmmmm........


Ft20/80 aka 80proof



:flipoff2:

[MT4Runner]

So it's #80?

It can't be #20....the tubing is bran' new, and it looks like it's never been welded to that frame and the frame looks fresh.

[EarlKann]

So it's #80?

It can't be #20....the tubing is bran' new, and it looks like it's never been welded to that frame and the frame looks fresh.


Yeah, #80 He reserved that particular number in advance. I think it's chromo also.:smokin:

[mobil1syn]

Here is a "Sneek Peak" at my new "Horsepower" for KOH '09!
ecotec?

[Heywood]

It looks odd:laughing:

[EarlKann]

ecotec?

I know but I'm not sure if I'm allowed to say. :( 5cyl vortec Colorado :blackflipoff2:

[ToolBox Guy]

Actually, the picture was just for the purpose of showing the motor.

The chassis number is 80 and I am somewhat sad to say that I will be stepping away from F-Toys, this one is already sold.

My new full tube car, on the other hand will be using that drivetrain, which is the new 5 cylinder-inline Vortec with a 4L60E auto tranny. The whole package is being setup in my new car by the guys at Power and Efficiency Systems.

After owning Heywoods car, I thought I would never leave a propane powered 22r, but this motor is to trick to pass up.

[mtbrjon]

What about front digs?

Safe with Longs and 37" tires?

Ask Wes #507.

[ls1andvortec]

Here is a pic of a simular engine installed on the test mule (1988 toyota truck) Sofar we have driven 11207 miles with planty of abuse and no failures or events sofar, We have been sharing endurance, engine temp numbers, fuel cumsumtion, trips (towing) and mileage driven information with TOOLBOX GUY. In reference to the initial question... all this tested on the stock 4 cyl diff with 4.10 gears 35" tires.

Engine info:
3.5 liter VORTEC I5
220 HP stock 240HP (software tweaks)
220 FTLBS stock 240 FTLBS (software tweaks)
Trans info:
4L60E
4 speed overdrive
TC info:
Dual toy TCs via ADVANCE ADAPTERS


http://photos1.hi5.com/0045/260/260/ZWr8AL260260-02.jpg

[desertoy]

ls1andvortec, we are all interested in how Bretts motor performs once he gets his rig done. Please keep us informed on how it goes. This motor might just turn out to be the replacement for the ecotec in rock crawling.

[Brian Ellinger]

ls1andvortec, we are all interested in how Bretts motor performs once he gets his rig done. Please keep us informed on how it goes. This motor might just turn out to be the replacement for the ecotec in rock crawling.

Id still like to build a buggy with a 7mgte and 300-400 hp. :evil: A 2jz would be really sweet, but they're expensive, and not the easiest to find either.

Toss the rad in the back, and Im pretty sure we could get one in our ftoy!

[Jeep07]

Ask Wes #507.

I installed the rear disco in 510 2 weeks ago. So far it works great with 40's and longs.

[ftoy507]

What about front digs?

Safe with Longs and 37" tires?

So far after one year of abuse mine has held up fine.
rear disco with 37 sticky trepadors and longs

Front burn not allowed in f oty comps.