We Have All Your Snorkel And Cold Air Intake Parts.

Need To Build A Snorkel Or Custom Cold Air Intake, We Have What You Need From Filters That Fit 3 To 4 Inch Tubes, All Colors Of Flex Tubing, And All Your Connectors And Pipes.

With All The Custom Builds We Do In This Sport An Off The Shelf Kit Just Want Work. Our Individual Parts Are A Fraction Of The Cost Of An Off The Shelf Kit.

So Let Us Supply You The Parts To Keep Your Engine Running Dirt And Water Free

let me take some measurments and ill tell you what i need.

Sounds Good.

ok,

i need an elbow for my gotpropane carb, 6" round and 4" tall, probably a reducer or whatever then 12" pipe, 45* elbow, then probably 24" and a filter for the end.

does that make sense?

Can You E-Mail Me A Picture Of Your Set Up With Measurmants At The Inlet Side Of The Propane unit. As Well As How Tall The Neck Is To The Inlet. May Have To Reduce At The Neck To Run The Rest Of The Pipe.

Send It To
ssines@moparsupercenter.com

you got an email

and here are the propane carb measurements if you need them...

http://img.photobucket.com/albums/v350/rajincajintj/IMAGE_075.jpg
http://img.photobucket.com/albums/v350/rajincajintj/IMAGE_076.jpg
http://img.photobucket.com/albums/v350/rajincajintj/propanecarbwithmeasurements.jpg

Plenum Box Is Easy. Perfect Fit.
http://www.jegs.com/images/photos/800/865/865-9843.jpg

Specs:

5 1/8 Diameter Neck

3.5 Inches Tall

4 Inch Inlet Tube.

Cost $64.99

Black Powder Coated Or Other Colors Available. Not On Our Site Yet But Will Be In A Minute.
Now Are You Trying To Build A Snorkel, Or Just A Filter?

not so much a snorkle as a cold air intake in the cab of the jeep.

i was going to use that pictured, to 12" straight (to go around the dist.) to a 45*bend to a straight through the firewall to the filter behind the dash.

Ok Easy Enough. Since I Don't Have Evarything On The Site Yet Let Me Get You Cost On The Other Parts.

Give Mer A Few Minutes.

thanks bro

Ok The Complete Kit Would Cost 205.87

To Include All Pipes, Clamps, Plenum, And Filter. All Polished Metal.

May Be Able To Make It Less Once i Found Out How Far The Plenum Comes Off For The Inlet. This Price Is With 2 12 Inch Runs Of Straight. If I Can Get Away With Just One 12 Inch And One 6 Inch Straight Run It Would Be About 20 Dollars Less.

Get The Complete Kit In Under 200 Dollars.

OK We Can Do It Without 2 12 Inch Straight Runs. Plenum Comes Over 9.5 Inches.
Now It Would Cost $176.21 Complete.

ok i see what you got, here is a list of what i would need:

plenum
12" straight pipe
45* joint
filter
all the clamps and such.

that should do me. it looks like the 9" on the plenum will clear the dist. to the pass side and a 45 will angle me enough towards the rear and from there im only 9 inches from the fire wall. so i look to have plenty room to clear the filter inside.

gimmie a price for all that shipped to 70124

thanks

$176.16 Shipped. All Hardware Included.:D

Thanks,
Scott Sines

paypal?

Credit Card Or Check.

Sorry About that.

ill give you a call tomorrow

No Worries

We Do Have A Line Of Less Bling Looking Filter Without The Stainless Steel. Just Black And Red. For Both The 3 And 4 Inch Intake Tubes. Also Cost A Good Bit Less.:D
That Way You Don't Look Like You Just Came From A Shooting Of Pimp My Ride.:laughing:

i have been looking for a snorkle set up for my 73 chevy k10 i have a edelbrock performer intake and AVS carb what kind of measurements do you need from me?? id like it to come out the p/s thank you

ROUGHNECK

I Will Need Neasurmants On The Carb Neck ( How Wide Across And Neck Height) To Start With. The Model Number Or Part Number Would Be A Great Starting Point. Just To See Which Adapters We Have That Might Fit. Than We Can Choose Pipe Size From There.

Than How Far Is It From The Center Of The Carb To The P/S Fender.

Then We Will Need To Know Where You Want The Snorkel Pipe To Come Out At. Do You Want It To Go Up The Windshield, Into The Cab Etc. Do You Want To Use A Cap Off Or Run A Cone Filter At The Top Of It.

Do You Want It To Stay On All The Time Or Run An Airbox That You Can Remove The Snorkel Pipe From, And Use A Regular Filter.

Just Kind Of Give Me An Idea As To What You Want We Can Design From There.

Thanks
Scott Sines

Looking for a cold air intake setup for a 95zj with a 4.0 and a 05 nissan pathfinder with a 4.0 shipped to 06451. Thanks

PM Sent

Thanks
Scott

I'd like a price for snorkel for an 89 XJ with 4.0. I'm still using the stock airbox, so nothing crazy to contend with.

Plenum Box Is Easy. Perfect Fit.
http://www.jegs.com/images/photos/800/865/865-9843.jpg

I'm building a dual canister filter intake setup, one on each side of my engine compartment, and need to split the intake at the Throttle Body towards the two filters.

Do you have anything for that?

If not, could I take two of the above pictured intakes, cut them in half, and TIG the two together? The key info on that is what is it made of?