|
: 4340 MOG 404 & 406 inner axles any length BranikMotorsports 12-10-2008, 06:44 AM we now have devleoped models and spline cutters to make 404 and 406 unimog inner axles any length. premium 4340 chromemoly. heat treated and cryogenic treated. call or pm for pricing! BranikMotorsports 12-18-2008, 01:57 PM bump BranikMotorsports 12-29-2008, 05:43 AM :grinpimp: extremetoy 01-07-2009, 07:44 PM how much for a ford 31 spline mog 404 axle, im unsure of the legnth but ill guess aprox. 36in out of the least expensive material thanks, Gary BranikMotorsports 01-08-2009, 10:51 AM We do ford 31 spline hybrid mog axles as well! xtremexj94 01-08-2009, 11:09 AM Can you guys do both front and rear shafts? BranikMotorsports 01-09-2009, 06:19 AM Can you guys do both front and rear shafts? yes we can, I'll post up some pics shortly BranikMotorsports 01-15-2009, 02:08 PM Here are pics of unimog 406 fronts and rears custom length and 4340 hardened and cryo treated!!!!!!!!!!! WE CAN ALSO MAKE ANY LENGTH 404 AXLES ALSO. jbell110 01-22-2009, 07:01 AM Sent a message to your home page, hope you got it!! Thanks Jeff Dr Dino 01-22-2009, 10:19 AM ttt jbell110 01-22-2009, 04:46 PM In case it didnt come through, I'm after a front short side axle with a long spline for the diff lock. I'm changing the diff from driver to passenger side, & a freight quote to Western Australia. Its a 404 axle thanks Jeff jbell110 01-24-2009, 06:01 PM ttt BranikMotorsports 01-26-2009, 05:57 AM pm sent, Thanks BranikMotorsports 02-01-2009, 12:16 PM ttt BranikMotorsports 02-09-2009, 04:26 PM ttt KILLER"B"3 02-09-2009, 06:42 PM thinking about going rear steer with my 404 rear. How much for stock length inners for a front axle? shipped to 37075 Thanks BranikMotorsports 02-12-2009, 10:35 AM pm sent thanks BranikMotorsports 02-18-2009, 10:15 AM bump BranikMotorsports 03-31-2009, 01:09 PM ttt X-Rated 04-10-2009, 05:38 PM Are the 406 shafts the same as a u1300 shaft? Any chance you will start making trunions so we can get complete replacement shafts with the joints YELLOWHOBO 04-11-2009, 12:47 AM How much for the rear short side 404 axles? seniorxj 04-13-2009, 07:52 AM Can you quote me a price on a full set of 4340 chromolys 27 spline with alloy x-joints,(or better), with full circle clips for a front HP d30 out of a 95 XJ,, and a price on 1541 dutchman shafts,(or better), for ford 8.8 31 spline shafts,, all shipped to 12303 ?? Do u sell master install kits?? Thank You!! BranikMotorsports 04-23-2009, 05:44 AM ttt BranikMotorsports 05-26-2009, 02:50 PM ttt xtremexj94 06-14-2009, 02:22 PM What are you charging for front Mog9 front shafts - does length matter? Also, have you guys considered doing something in 1541H to give another more economical option for us guys that don't have megabucks to spend? BranikMotorsports 06-16-2009, 05:01 AM pmsent BranikMotorsports 06-18-2009, 05:39 AM Ttt chad551 06-18-2009, 03:13 PM Axle from a Grand Waggy D44 need new chromo axles 2 outer axle shafts both sides are 9.94" 2 inner axle shafts driver-side 15.8" and passenger-side 32.12" Shipped to 63139 xtremexj94 06-18-2009, 09:14 PM Axle from a Grand Waggy D44 need new chromo axles 2 outer axle shafts both sides are 9.94" 2 inner axle shafts driver-side 15.8" and passenger-side 32.12" Shipped to 63139 Dude, did you not read the title of this thread? It is for 4340 Mog 404 and 406 shafts, not for standard diffs.:shaking: Just pointing out the obvious. BranikMotorsports 08-20-2009, 05:25 AM ttt xtremexj94 08-20-2009, 08:34 AM Stan, check your PMs.:D xtremexj94 08-25-2009, 01:48 PM Stan, check your PMs again.;) WillisXJ 08-25-2009, 10:54 PM Price for short rear shaft to center pumpkin And price for front shaft to shorten shorter side to match rear width. BranikMotorsports 09-14-2009, 08:01 AM thanks BranikMotorsports 10-12-2009, 05:27 AM ttt smithm 10-19-2009, 01:15 PM sent you a pm about some 404 axle shafts. Thanks BranikMotorsports 10-20-2009, 07:17 AM thanks BranikMotorsports 10-23-2009, 07:08 AM ttt BranikMotorsports 10-29-2009, 01:45 PM machining 2 sets 404 fronts now! BranikMotorsports 11-09-2009, 01:42 PM we are making axle shafts for Volvo portals, gen 3, portal tek also. BranikMotorsports 11-18-2009, 07:58 AM Bump BranikMotorsports 12-09-2009, 01:59 PM ttt BranikMotorsports 12-23-2009, 05:32 AM ttt BranikMotorsports 01-21-2010, 10:43 AM ttt BranikMotorsports 01-30-2010, 11:43 AM ttt tjmark 05-12-2010, 01:17 PM Up for ya just ordered a hybrid shaft today... BranikMotorsports 07-22-2010, 12:59 PM ttt BranikMotorsports 08-23-2010, 02:32 PM ttt BranikMotorsports 09-10-2010, 12:03 PM NEW 404 STEEL PORTAL BOXES!!!!!!!! Coming soon...prototyping nearly done!!!!!!!! Aaronius 10-27-2010, 11:26 PM Do you or can you make the outer "stub" shaft for a front 404? Price? Thanks BranikMotorsports 11-17-2010, 05:24 AM ttt BranikMotorsports 01-13-2011, 06:37 PM ttt BranikMotorsports 03-11-2011, 06:16 AM ttt BranikMotorsports 06-13-2011, 12:06 PM ttt stjjames 06-13-2011, 03:47 PM NEW 404 STEEL PORTAL BOXES!!!!!!!! Coming soon...prototyping nearly done!!!!!!!! Pics !!!:flipoff2: BranikMotorsports 06-28-2011, 02:08 PM Pics !!!:flipoff2: what? go to "weps" search for portal boxes these are his, we are just the mfg:grinpimp: oh and they are no longer "prototype" go to "WEPS" on pbb for details BranikMotorsports 07-28-2011, 02:30 PM to the top BranikMotorsports 08-26-2011, 05:36 AM ttt BranikMotorsports 10-05-2011, 07:34 AM to the top BranikMotorsports 10-29-2011, 06:07 AM bump for more BranikMotorsports 12-16-2011, 08:15 AM bump | |