This is not something I am going to quit selling, so thanks for all the orders. Been selling since 2006 and plan to sell for many years to come.

I am selling a complete bolt on disc brake conversion kit for $315 including shipping to anywhere in the lower 48 states! Yep I really mean complete - here's what you get:

3/8" thick laser cut brackets
DOM bracket spacers (when needed)
grade 8 mounting hardware
new GM rotors
rebuilt GM calipers with steel pistons
semi metallic brake pads
new inner hub seals
new caliper pins
rubber flex hoses
banjo bolts with copper washers
anti-rattle clips

http://www.mustangfarm.com/forsale/reardisc.jpg

I have kits for these axles:

73-87 Chevy single rear wheel full floater 14 bolt axle 10.5" ring gear

62-72 Eaton corporate rear end, full floater ( same kit as the 73-87 14 bolt)

73-87 Chevy cab and chassis full floater 14 bolt axle 10.5" ring gear

88-up second generation 14 bolt 10.5 full floater/ need to know:
if drums slide off after removing wheel-need "gen 2" kit/ if wheel is removed and drum is behind the wheel hub and studs then you need the 73-87 14 bolt kit. (there is no reasoning as to what year will have what, we have seen both versions all thru the 90s)

79-up 14 bolt semi-float 6 or 8 lug 9.5" rear axle / not positive what year this axle was first produced / this kit sells for $340.00 because new wheel studs come with it.

72-79 Ford dana 60 rear axle/ have found that it will fit 68-71 ford dana 60 rear axles but slight spacer modification is sometimes required using flat washers.

76-93 Dodge dana 60 rear axle

94-up Dodge dana 60 rear axle - Weld on kit only

68-72 Chevy dana 60 rear axle

72-up Jeep pick-up dana 60 rear axle( jeep took over the gm dana 60 rear axle in 1972 when chevy dumped it in favor of the 14 bolt) same kit as the chevy 60

Ford sterling axle - $390 (uses special rotors)

Other axles? Generally I have found that these same rotors will work on most other axles, but you will need to use weld on brackets. Just tell me the diameter of the tube near the end of the axle and I will send you weld on brackets.

Instructions? No I don't have detailed instructions. This is really simple to install for anyone who has a clue about how brakes work. Only word of advise is most of my kits require the rotor on the backside of the hub.

Emergency brakes? Yes, I have eldarodo calipers for $200 more. This gives a manual e-brake that hooks up to your cables.

I accept paypal or postal money orders. Orders will ship from TN. I just do this as a side job, so it takes a day or two to box it up and ship out. I do not sell to or ship to Canada.

Send paypal to gubni at comcast.net and include the year and type of axle you need the kit for.

You can also call me if you want but I cannot accept credit cards over the phone. 423-737-0265 -- Shawn

Upgrade to braided stainless hoses for only $20 more.

http://www.mustangfarm.com/forum/hoses.jpg

I am selling a complete bolt on disc brake conversion kit for $315 including shipping to anywhere in the lower 48 states! Yep I really mean complete - here's what you get:

3/8" thick laser cut brackets
DOM bracket spacers
grade 8 annodized mounting hardware
new GM rotors
rebuilt GM calipers with steel pistons
semi metallic brake pads
new inner hub seals
caliper pins
rubber flex hoses
banjo bolts with copper washers
anti-rattle clips

http://www.mustangfarm.com/forsale/reardisc.jpg

I have kits for these axles:

73-87 chevy single rear wheel full floater 14 bolt axle 10.5" ring gear

62-72 eaton corporate rear end, full floater ( same kit as the 73-87 14 bolt)

88-up second generation 14 bolt 10.5 full floater/ need to know:
if drums slide off after removing wheel-need "gen 2" kit/ if wheel is removed and drum is still captured by wheel hub and studs then customer needs 73-87 14 bolt kit. (there is no reasoning as to what year will have what, we have seen both versions all thru the 90s)

79-up 14 bolt semi-float 6 lug 9.5" rear axle / not positive what year this axle was first produced / this kit sells for $330.00 because new wheel studs come with it.

79-up 14 bolt semi-float 8 lug 9.5" rear axle / basically same details as 6 lug kit including price of $330

72-79 ford dana 60 rear axle/ have found that it will fit 68-71 ford dana 60 rear axles but slight spacer modification is sometimes required using flat washers.

76-93 dodge dana 60 rear axle

94-up dodge dana 60 rear axle

68-72 chevy dana 60 rear axle

72-up jeep pick-up dana 60 rear axle( jeep took over the gm dana 60 rear axle in 1972 when chevy dumped it in favor of the 14 bolt) same kit as the chevy 60

Other axles? Generally I have found that these same rotors will work on most other axles, but you will need to use weld on brackets. Just tell me the diameter of the tube near the end of the axle and I will send you weld on brackets.

Instructions? No I don't have detailed instructions. This is really simple to install for anyone who has a clue about how brakes work. Only word of advise is most of my kits require the rotor on the backside of the hub.

Emergency brakes? Sorry, but I don't offer them. I reccomend a "line lock", but if you can get different calipers I will take off $45 from my price without loaded calipers.

I accept paypal or postal money orders. Orders will ship from west TN generally on weekends. I do not sell to or ship to Canada. Send paypal to gubni at comcast dot net and include the year and type of axle you need the kit for. You can also call me if you want 423-737-0265 -- Shawn. I cannot accept credit cards over the phone at this time.

you got paypal bro!

Have a Kit for C&C 14 bolts?

Have a Kit for C&C 14 bolts?

My kits don't fit dually or CC 14 bolts because the backing plate is so far from the hub the spacer would have to be too long. I can hook you up with a weld on kit.

What about a '87 GM D70HD?

What about a '87 GM D70HD?

Generally I have found that these same rotors will work on most other axles, but you will need to use weld on brackets. Just tell me the diameter of the tube near the end of the axle and I will send you weld on brackets at the same price.

I have 6 sets of eldarodo calipers. This gives you an emergency brake for $200 more per kit. Only available with purchase of a kit. They are not ready to ship, but will soon. I'm having the custom levers made for them. If you want one let me know as last time I got some they sold out in a week.

I have 6 sets of eldarodo calipers. This gives you an emergency brake for $200 more per kit. Only available with purchase of a kit. They are not ready to ship, but will soon. I'm having the custom levers made for them. If you want one let me know as last time I got some they sold out in a week.

Only 3 sets left. These should be ready to ship by Monday.

Just need the bottom half of you parts list:
rebuilt GM calipers with steel pistons
semi metallic brake pads
new inner hub seals
caliper pins
rubber flex hoses
banjo bolts with copper washers
anti-rattle clips

How much for that shipped to 80104?

Just need the bottom half of you parts list:
rebuilt GM calipers with steel pistons
semi metallic brake pads
new inner hub seals
caliper pins
rubber flex hoses
banjo bolts with copper washers
anti-rattle clips

How much for that shipped to 80104?

PM sent.

btt

Thanks for the orders.

[QUOTE=GubNi;9210075]I am selling a complete bolt on disc brake conversion kit for $315 including shipping to anywhere in the lower 48 states! Yep I really mean complete - here's what you get:

I have a 1990 Chevy Dually and would like to put rear disc brakes on it. Does your kit have all the parts or what would I have to add? I installed disc rear brakes on my 1979 CJ7 and your kits looks very much the same. Please provide the price and if you have one kit in.


I use PayPal so if this is ok, I will order a set. Do you have an e-brake?


What info do you need from me or pictures? John


Please email if you have any questions. sclevall@aol.com

[QUOTE=GubNi;9210075]I am selling a complete bolt on disc brake conversion kit for $315 including shipping to anywhere in the lower 48 states! Yep I really mean complete - here's what you get:

I have a 1990 Chevy Dually and would like to put rear disc brakes on it. Does your kit have all the parts or what would I have to add? I installed disc rear brakes on my 1979 CJ7 and your kits looks very much the same. Please provide the price and if you have one kit in.


I use PayPal so if this is ok, I will order a set. Do you have an e-brake?


What info do you need from me or pictures? John


Please email if you have any questions. sclevall@aol.com

My kit is complete with no other parts needed.

Yes, paypal is ok.

The standard kit does not have ebrake. For $200 extra we will include special ebrake calipers.

My kit is not compatible with dually axles.

Do you still have these with the ebrake calipers? Do the calipers have the ebrake lever and spring?

Do you still have these with the ebrake calipers? Do the calipers have the ebrake lever and spring?


Yes, and yes!

btt

sending paypal right now .... thanks from a former Tri-City Resident :flipoff2:

EDIT: you should probably add in that you refuse payments to non-confirmed addresses via paypal. would have saved me from having paypal put a 1 week hold on my monies ...

Will your kit work on a 1998 Dodge dana 60 with 3 1/2 axles tubes?

Brian

Will your kit work on a 1998 Dodge dana 60 with 3 1/2 axles tubes?

Brian


Yes, it works on 94-up dodge dana 60 rear axle

I just ordered these brackets before I saw your thread.
http://www.pirate4x4.com/forum/showthread.php?t=649888
Could you work me up a price minus the brackets?
Thanks

I just ordered these brackets before I saw your thread.
http://www.pirate4x4.com/forum/showthread.php?t=649888
Could you work me up a price minus the brackets?
Thanks


Without brackets saves $40 so $275

Without brackets saves $40 so $275

My rear hubs have 1/2" studs in them. Is that what will fit the rotors?

My rear hubs have 1/2" studs in them. Is that what will fit the rotors?


My rotors work with 1/2" and 9/16" studs.

Payment sent. Thank you

Will this kit work with 15" wheels?

Will this kit work with 15" wheels?

It works with most depending on backspacing. It will work with all 15" rims with 3" or less backspacing. It works with most that have 3.5" or less. It will not work with most that have 4" or more.

Price on the 14 bolt kit shipped to 95209.....Thanks!

Price on the 14 bolt kit shipped to 95209.....Thanks!

My price of $315 includes shipping.

My price of $315 includes shipping.

10-4...I will be placing an order real soon! Thanks!

Sean,

I will give you a ring tomarrow. I would like to order the kit...Thanks Ron

Sean...I paypal'd you the money . Please PM or email when the kit will ship and tracking number.

Thanks Ron

Will do.

Will do.

Thanks!

Hey Shawn,

Placed an order, please PM me when they ship out and if you could send me a tracking number that would be great!

Thank you,
Adam

How much for everything minus brackets shipped to 95662?

new GM rotors
rebuilt GM calipers with steel pistons
semi metallic brake pads
new inner hub seals
caliper pins
rubber flex hoses
banjo bolts with copper washers
anti-rattle clips

How much for everything minus brackets shipped to 95662?

new GM rotors
rebuilt GM calipers with steel pistons
semi metallic brake pads
new inner hub seals
caliper pins
rubber flex hoses
banjo bolts with copper washers
anti-rattle clips

Shipping is flat rate and included in the price. Take off $40 without brackets and bracket bolts.

How much for the brackets, axle seals, and rotors for a 79 Jeep J20 dana 60?

pm sent

PM Sent.

Thanks,

Tim

PM sent

Bump for a great seller!

Parts came quickly and everything is very nice.

Don't hesitate to order anything from this guy!

Thanks again

Ordered mine today:D I upgraded to the e-brake calipers:smokin:

Sean, let me know when those ship out. Thanks again
josh

Got them out last night. Takes about a week to get to the west coast though.

Good deal. Just sent you money.

Do you still have this kit available for an early '90s 14 bolt SF 6 lug?

Can you also point me in the direction of a manual line lock (one that doesn't require power)?

Thanks

how much for the complete brake parts kit minus the axle brackets. i already have brakets. for 85' 14bolt srw. shipped to 29070 thanks. let me know

how much for the complete brake parts kit minus the axle brackets. i already have brakets. for 85' 14bolt srw. shipped to 29070 thanks. let me know


Yes I still sell them and plan to for several years.

No brackets saves $40

My price of $315 includes shipping, so $275 without brackets.

has anybody put this kit on a dodge dana 60 HD rear. if so, do you have any pics and did you have problems.
thanks

I have sold several kits for dodge. As long as it's a normal 60 with the years listed no problems, but military axle and other years can be troublesome.

Early srw 14 bolt kit. I have heard that the hubs need to be changed due to the back side of the hub not being machined. Is that the case? Pricing, details, please thanks.

Early srw 14 bolt kit. I have heard that the hubs need to be changed due to the back side of the hub not being machined. Is that the case? Pricing, details, please thanks.

Never heard of that problem and I've sold a few hundred early 14 bolt kits.

can i get a quote without the brackets for the early 14 bolt shipped to 96795?
Thanks

can i get a quote without the brackets for the early 14 bolt shipped to 96795?
Thanks

No brackets saves $45 and shipping is included. $270

Never heard of that problem and I've sold a few hundred early 14 bolt kits.
Just so I am clear. The hubs I have are the type that the drums slide off (not pressed on). Is the kit the same? Do you have to press the studs out, install rotor and new studs from the back side?

Just so I am clear. The hubs I have are the type that the drums slide off (not pressed on). Is the kit the same? Do you have to press the studs out, install rotor and new studs from the back side?

Rotor goes on the back side and studs go through the rotor into the hub.

Thanks for all the orders. Sorry, but I won't be able to try to PMs until Monday. Going to Harlan. Hope to see you there.

btt

Paypal has been sent

Hey, I all ready have the brackets, how much for everything else shipped to zip 92071? Do you also have longer wheel studs? Thanks, Jeff

No bracket saves $45.00

I don't have or reccomend longer studs unless it's a semi float.

Do you have everything in stock minus the barckets? If so I would like to order it. Total would be $270. delivered, correct? Thanks, Jeff

Do you have everything in stock minus the barckets? If so I would like to order it. Total would be $270. delivered, correct? Your paypal is gubni at comcast dot net correct? Thanks, Jeff

All correct except I don't keep parts in stock. I get them locally though, so no problems there.

Thanks! I received my parts order yesterday, super fast shipping , every thing just as pictured, great deal. Thanks Again, Jeff

First off do you have a set of brackets for the 88-98 style 14 sf 6 lug? Second how much would a set of brackets with the brake lines cost? Lastly what year and model do the calipers come from, and is that year and model the same for the rotors, Thanks, looks like you have a great kit!!!

Also I have 15" wheels long shot but will they fit over your kit for the above mentioned axle?

First off do you have a set of brackets for the 88-98 style 14 sf 6 lug? Second how much would a set of brackets with the brake lines cost? Lastly what year and model do the calipers come from, and is that year and model the same for the rotors, Thanks, looks like you have a great kit!!!

I checked my list of axles and found I have a kit for 79-up 14 bolt semi-float 6 lug 9.5" rear axle. This kit sells for $330.00 because new wheel studs come with it. I sell it as a complete kit with calipers and rotors. If you just want brackets and lines then $100 shipped. The calipers and rotors are from an early 80's chevy 3/4 ton 4x4 truck front. Don't forget you will need studs, banjo bolts, caliper pins, and brake pads in addition to the rotors and calipers.

Generally 15" wheels will fit, but it depends on the backspacing. All 3" or less will fit. All 5" or more will not. From 3" to 5" depends on the wheel.

alright here is a tricky question for you, my wheels barely fit over a dana 44 caliper setup with the 73-76 chevy 6 bolt outers does that help determine if my wheels will clear the conversion? If I get the brackets and they don't fit what kind of return policy do you offer?

alright here is a tricky question for you, my wheels barely fit over a dana 44 caliper setup with the 73-76 chevy 6 bolt outers does that help determine if my wheels will clear the conversion? If I get the brackets and they don't fit what kind of return policy do you offer?

If they fit over those they should fit over mine. Sorry, but no refunds.

will this kit work on a dynatrac pro rock 60 rear




I am selling a complete bolt on disc brake conversion kit for $315 including shipping to anywhere in the lower 48 states! Yep I really mean complete - here's what you get:

3/8" thick laser cut brackets
DOM bracket spacers
grade 8 annodized mounting hardware
new GM rotors
rebuilt GM calipers with steel pistons
semi metallic brake pads
new inner hub seals
caliper pins
rubber flex hoses
banjo bolts with copper washers
anti-rattle clips

http://www.mustangfarm.com/forsale/reardisc.jpg

I have kits for these axles:

73-87 chevy single rear wheel full floater 14 bolt axle 10.5" ring gear

62-72 eaton corporate rear end, full floater ( same kit as the 73-87 14 bolt)

88-up second generation 14 bolt 10.5 full floater/ need to know:
if drums slide off after removing wheel-need "gen 2" kit/ if wheel is removed and drum is still captured by wheel hub and studs then customer needs 73-87 14 bolt kit. (there is no reasoning as to what year will have what, we have seen both versions all thru the 90s)

79-up 14 bolt semi-float 6 lug 9.5" rear axle / not positive what year this axle was first produced / this kit sells for $330.00 because new wheel studs come with it.

79-up 14 bolt semi-float 8 lug 9.5" rear axle / basically same details as 6 lug kit including price of $330

72-79 ford dana 60 rear axle/ have found that it will fit 68-71 ford dana 60 rear axles but slight spacer modification is sometimes required using flat washers.

76-93 dodge dana 60 rear axle

94-up dodge dana 60 rear axle

68-72 chevy dana 60 rear axle

72-up jeep pick-up dana 60 rear axle( jeep took over the gm dana 60 rear axle in 1972 when chevy dumped it in favor of the 14 bolt) same kit as the chevy 60

Other axles? Generally I have found that these same rotors will work on most other axles, but you will need to use weld on brackets. Just tell me the diameter of the tube near the end of the axle and I will send you weld on brackets.

Instructions? No I don't have detailed instructions. This is really simple to install for anyone who has a clue about how brakes work. Only word of advise is most of my kits require the rotor on the backside of the hub.

Emergency brakes? Sorry, but I don't offer them. I reccomend a "line lock", but if you can get different calipers I will take off $45 from my price without loaded calipers.

I accept paypal or postal money orders. Orders will ship from west TN generally on weekends. I do not sell to or ship to Canada. Send paypal to gubni at comcast dot net and include the year and type of axle you need the kit for. You can also call me if you want 423-737-0265 -- Shawn. I cannot accept credit cards over the phone at this time.

will this kit work on a dynatrac pro rock 60 rear

I don't know what pattern their backing plate is. According to their website the standard lug pattern is 6x5.5 and most of mine are 8 lug, so probably not. If you could PM me some details about your axle I might be able to help more.

for those of you who have bought this kit how has the install went and how well did you like the results?

do you sell the brackets for a chevy dana 60 front to run 15 inch wheels?

do you sell the brackets for a chevy dana 60 front to run 15 inch wheels?

I don't sell just brackets, but $350 shipped for the entire kit.

this seems like a fair price and would save me hunting it all down....does it come with directions lol

this seems like a fair price and would save me hunting it all down....does it come with directions lol

Sorry, but no directions. The hardest part is getting the drum brakes off. The rest is very simple.

You said rotors and calipers are from early chevy 4wd truck fronts, can you be a little more specific on what years and 1/2-3/4-1 ton?

Also, i'm sure you are getting tired of answering this but i saw the price changed a few bucks throughout the thread, is it still $270 shipped for the standard kit without brackets, and $470 shipped with eldo calipers? With the eldo calipers you metioned a custom lever, what lever are you talking about, or what else that isnt with the standard kit is included in that setup?

Thanks.

You said rotors and calipers are from early chevy 4wd truck fronts, can you be a little more specific on what years and 1/2-3/4-1 ton?

Also, i'm sure you are getting tired of answering this but i saw the price changed a few bucks throughout the thread, is it still $270 shipped for the standard kit without brackets, and $470 shipped with eldo calipers? With the eldo calipers you metioned a custom lever, what lever are you talking about, or what else that isnt with the standard kit is included in that setup?

Thanks.

There are many years that will work such as 1980. 8 lug kits are 3/4 ton. No brackets saves $45, so $270 add $200 for ebrake calipers so $470 shipped. There is a lever needed to attach the ebrake cable to the caliper. It's not included if you buy the calipers anywhere else. I have them specially made and include it with my kit. That's the only specially made part.

does the 60 conversion come with studs? if not, what lug studs will work with the 60 conversion?

does the 60 conversion come with studs? if not, what lug studs will work with the 60 conversion?

No it doesn't come with them or need new ones. Just reused the ones you have.

I have a Dana 60 Full Float(32 spline) under my Ford E350 van...the Drums are HUGE!!!

I'd like to know if you've sold any of these kits to any Ford Van owners?

If so...have you had any feedback on the install?

THanks

I have a Dana 60(32 spline) under my Ford E350 van...the Drums are HUGE!!!

I'd like to know if you've sold any of these kits to any Ford Van owners?

If so...have you had any feedback on the install?

THanks


None to a Van. Is it semi float? Are you sure it's a Dana 60 and not a Dana 61? Send me a PM with details.

I now accept credit cards by phone.

Many E350s had a Dana 60U underneath. They have 3.5" tubes, smooth bottom diff and Dana 70 like hubs.

btt

make a bolt on kit for a 1987 j-20 d60? if so price shipped to 13073

make a bolt on kit for a 1987 j-20 d60? if so price shipped to 13073

I checked the list one the first page and found 72 up jeep listed. Also all of my kits have free shipping in the lower 48 states.

What is the difference (as far as the kit goes) between the late model and early model 14B kits?
How does the kit overcome the issue with the hub on the later model not being machined flat?
Lastly, are the components in your kit compatible with the brackets sold by Ballistic? http://www.ballisticfabrication.com/14-Bolt-Bolt-on-Caliper-Bracket_p_1603.html#

What is the difference (as far as the kit goes) between the late model and early model 14B kits?

The flange on the axle is different, which means my bracket is different. The rest is the same.

How does the kit overcome the issue with the hub on the later model not being machined flat?

Never found this to be a problem. I've sold many and nobody has ever told me there was an issue. If it helps any the rotor goes on the back side of the hub.


Lastly, are the components in your kit compatible with the brackets sold by Ballistic? http://www.ballisticfabrication.com/14-Bolt-Bolt-on-Caliper-Bracket_p_1603.html#


I don't see why not. I can't guarantee my parts and someone elses will work, but I think they will.

I have a rear axle in my trail rig out of a military Land Rover, it's a D60, but among other things, the bolt pattern is 5X6.5.

Whatcha got for me?

I have a rear axle in my trail rig out of a military Land Rover, it's a D60, but among other things, the bolt pattern is 5X6.5.

Whatcha got for me?

Nothing. The odd lug pattern will make it a custom job. You will need to find a rotor that will fit your hub and then drill your lug pattern into it.

Nothing. The odd lug pattern will make it a custom job. You will need to find a rotor that will fit your hub and then drill your lug pattern into it.

I have the rotors, $35/ea at Napa!

I have the rotors, $35/ea at Napa!

Pm sent

Still have these? Will be ordering one soon (within the next week)

1979 Dodge Dana 60 Rear
8 Lug
4 Stud Flange
3 3/8" x 3 3/8" mounting

Still have these? Will be ordering one soon (within the next week)

1979 Dodge Dana 60 Rear
8 Lug
4 Stud Flange
3 3/8" x 3 3/8" mounting
non e-brake

Still have these? Will be ordering one soon (within the next week)


Still sell them every week.

Will be ordering one in the near future 14-bolt gen-2 with slide off drums.

Bump for ya.:D

Will be ordering one in the near future 14-bolt gen-2 with slide off drums.

Bump for ya.:D

X dos :D

any pics of the "second generation" 14 bolt kit mounted up?:smokin:

any pics of the "second generation" 14 bolt kit mounted up?:smokin:

Sorry, but no.

Can I get a price on the kit minus the caliper brackets/spacer?? I already have a disc caliper adapter but need the guts of the swap.

Can I get a price on the kit minus the caliper brackets/spacer?? I already have a disc caliper adapter but need the guts of the swap.

Without brackets saves you $40 so $275

I have a duel rear wheel 14 bolt and looking for a kit, can you help me out?

I have a duel rear wheel 14 bolt and looking for a kit, can you help me out?

I can sell you a kit that will work for dually with weld on brackets for the same price.

anything for a 1973 dodge dana 60

anything for a 1973 dodge dana 60

I checked my list and found I do have 76-93 dodge dana 60 rear axle. What that really means is that I don't have a pre 76 axle to test and the books don't give me info on it. I know everything will be the same except the bracket. I can provide you with a kit that includes a weld on bracket for the same price of $315

Can I get a price on

3/8" thick laser cut brackets
DOM bracket spacers
grade 8 annodized mounting hardward
new inner hub seals
caliper pins
rubber flex hoses
banjo bolts with copper washers
anti-rattle clips

It's for a 75 14 bolt. ZIp code 94551. Thanks

ordered mine a couple days ago. thanks shawn!

Can I get a price on

3/8" thick laser cut brackets
DOM bracket spacers
grade 8 annodized mounting hardward
new inner hub seals
caliper pins
rubber flex hoses
banjo bolts with copper washers
anti-rattle clips

It's for a 75 14 bolt. ZIp code 94551. Thanks


$175 shipped

Yep looking for disk brakes for J20 dana 60
How do I get ahould of you and send you payment??

Yep looking for disk brakes for J20 dana 60
How do I get ahould of you and send you payment??

I prefer you send money by paypal to gubni at comcast dot net. Of course use . instead of dot and @ instead of at.

If you need to get ahold of me send a PM, email me, or call me at 423-737-0265

You can also call me with a credit card or send a postal money order.

btt

Do you have a kit that will convert my DRW FF 14bolt to a SRW? I seen you talking about a weld on kit. Im just wondering.

I dont mean to be repetitive. If it is i apologize.

Do you have a kit that will convert my DRW FF 14bolt to a SRW? I seen you talking about a weld on kit. Im just wondering.

I dont mean to be repetitive. If it is i apologize.

You do realize you need to change the hubs over (DRW to SRW) to accomplish this right?

Do you have a kit that will convert my DRW FF 14bolt to a SRW? I seen you talking about a weld on kit. Im just wondering.

I dont mean to be repetitive. If it is i apologize.

PM sent

For every new order between now and the 23rd I will donate $20 to a family in need.

quote me a full kit for a gen 1 FF14B SRW to 37932 (lol ... nevermind ... i see its 315 shipped :laughing: )

also ... can you add in inner and outter hub bearings / races or am i better off getting these on my own?

EDIT: and can you quote with and without rotors ... thanks.

quote me a full kit for a gen 1 FF14B SRW to 37932 (lol ... nevermind ... i see its 315 shipped :laughing: )

also ... can you add in inner and outter hub bearings / races or am i better off getting these on my own?

EDIT: and can you quote with and without rotors ... thanks.

I don't have a good source on bearings and races. No rotors saves $45.00.

btt

3/8" thick laser cut brackets
DOM bracket spacers
banjo bolts with copper washers

how much shipped to 07849 for a 73-93 dodge dana 60?

Do you have a kit for the 14 bolt with 5 on 5 1/2 bolt pattern???

3/8" thick laser cut brackets
DOM bracket spacers
banjo bolts with copper washers

how much shipped to 07849 for a 73-93 dodge dana 60?

PM sent

Do you have a kit for the 14 bolt with 5 on 5 1/2 bolt pattern???

No, I specialize in 8 lug brakes.

do you know what wheel studs to use with this kit? ('79 f-250 D60)

do you know what wheel studs to use with this kit? ('79 f-250 D60)

My kit allows you to reuse your stock studs.

I don't have a good source on bearings and races. No rotors saves $45.00.

thanks.

Is there any way to modify your kit to work with 4.5 backspacing on 78 Ford D60?


It works with most depending on backspacing. It will work with all 15" rims with 3" or less backspacing. It works with most that have 3.5" or less. It will not work with most that have 4" or more.

Is there any way to modify your kit to work with 4.5 backspacing on 78 Ford D60?

Sure, just add some wheel spacers. PM sent.

Thanks for all the orders.

Many E350s had a Dana 60U underneath. They have 3.5" tubes, smooth bottom diff and Dana 70 like hubs.

THat seems to be what I have...The tubes are deffinately 3.5" and the drums slide right off of the hub/studs... And I seem to be going through the same bracket issues that most people doing Dana 60's disc swaps are experiencing. :rolleyes: :shaking: Oh well...it'll get worked out one way or another...:D

THat seems to be what I have...The tubes are deffinately 3.5" and the drums slide right off of the hub/studs... And I seem to be going through the same bracket issues that most people doing Dana 60's disc swaps are experiencing. :rolleyes: :shaking: Oh well...it'll get worked out one way or another...:D

Sounds like my kit would probably work for you.

The hell of it is that I've got the RuffStuff Bent D60 caliper brackets, the Chevy 3/4 ton Rotors and front calipers...

I'm concerned that the studs are either going to be too short or the knurl on the studs is going to be too short to hold the rotor to the backside of my hub...

The hell of it is that I've got the RuffStuff Bent D60 caliper brackets, the Chevy 3/4 ton Rotors and front calipers...

I'm concerned that the studs are either going to be too short or the knurl on the studs is going to be too short to hold the rotor to the backside of my hub...


For some reason I've had several people ask about studs recently. There's no need to change the studs except on semi-float 14 bolt axles.

Is there a problem or a difference running your kit on a dodge van dana 60 1996 with the offset rear pumpkin? with the abs sensor in the pumpkin

Im not going to use ABS, just stateing what axle i have.

seems to me the brakes would not be effected by the offset pumpkin

Is there a problem or a difference running your kit on a dodge van dana 60 1996 with the offset rear pumpkin? with the abs sensor in the pumpkin

Im not going to use ABS, just stateing what axle i have.

seems to me the brakes would not be effected by the offset pumpkin

No problem - that's in my list of supported axles.

Got my kit in today Shawn, Top notch stuff!


Thanks for the great service/price :smokin:

Interested in one of your kits for a Dana 60. Haveing trouble identifying exactly what 60 I have. BOM appears to be gone. There is a C 32055 part number on the housing. Is there any other way that I can figure out what axle this is and what kit I need?

No other easy way. We might be able to take a good guess based on the bolt pattern of the flange where the backing plate mounts to.

Just sent you some money for a full set up for 78' ford ff 60 rear.

how much for the tail end of your list shipped to 34479

grade 8 annodized mounting hardware
new GM rotors
rebuilt GM calipers with steel pistons
semi metallic brake pads
new inner hub seals
caliper pins
rubber flex hoses
banjo bolts with copper washers
anti-rattle clips

how much for the tail end of your list shipped to 34479

grade 8 annodized mounting hardware
new GM rotors
rebuilt GM calipers with steel pistons
semi metallic brake pads
new inner hub seals
caliper pins
rubber flex hoses
banjo bolts with copper washers
anti-rattle clips

I think you are trying to say no brackets or spacers. If so then that saves $40 so the price would be $275

Any ideas if your kit will work on a 70's Ford D60HD? Not exactly sure on the year yet but will get the BOM this weekend.

Any ideas if your kit will work on a 70's Ford D60HD? Not exactly sure on the year yet but will get the BOM this weekend.

Yes, it will work on all Ford 60's.

quote on everything but the brackets and spacers

quote on everything but the brackets and spacers

That saves $40. $275 shipped

btt

Hey, how much for shipping on the 14 bolt sf 6 lug to 14226?
Thanks!!!
Matty

Hey, how much for shipping on the 14 bolt sf 6 lug to 14226?
Thanks!!!
Matty

Free shipping. Semi-float is $335

Awesome! Be in touch tomorrow!

Still have any Eldo Calipersleft to go with your kits?

Still have any Eldo Calipersleft to go with your kits?

Yep.

btt

Great deal! I will definitely be buying a kit once I find one that fits a D60HD from a 70's Ford. The only difference between that and a regular D60, as far as I can tell, is the axle tubes are 3 1/8" in diameter and the center section has extra webs on it for strength. Any idea if your caliper brackets fit? If not, I'm guessing only slight modification is necessary to open up the center hole a little.

Great deal! I will definitely be buying a kit once I find one that fits a D60HD from a 70's Ford. The only difference between that and a regular D60, as far as I can tell, is the axle tubes are 3 1/8" in diameter and the center section has extra webs on it for strength. Any idea if your caliper brackets fit? If not, I'm guessing only slight modification is necessary to open up the center hole a little.

My ford kit fits that axle.

My ford kit fits that axle.

Awesome! Will be ordering soon :smokin:

ordered
Thanks

btt

Just placed order, looking forward to having rear brakes:D

paypal, pm sent!

Will be placing a order as soon as I figure out if I have a FF or SF.

Ignore the number of lug nuts in this picture. Look at the area in the middle of the end of the axle. One on the left is semi float and on the right is full float.

http://www.venturesparts.com/uploads/images/Semi_Floating_Axle.JPG http://www.venturesparts.com/uploads/images/14_Bolt_Full-Floating_Axle.JPG

installed it the other day... good product so far...thnx :D

Ignore the number of lug nuts in this picture. Look at the area in the middle of the end of the axle. One on the left is semi float and on the right is full float.

http://www.venturesparts.com/uploads/images/Semi_Floating_Axle.JPG http://www.venturesparts.com/uploads/images/14_Bolt_Full-Floating_Axle.JPG


Thanks. I knew the difference after searching online last night. Now I just need to pull a wheel off to see. I think I have the 10.5 ring gear but I will check tonight.

Also, I've heard many different reviews of the brackets from bent ones to striaght ones with spacers. I assume that you would recommend the ones you sell. But has anyone had any problems with either. Just wondering. Still gonna get yours though. Thanks

installed it the other day... good product so far...thnx :D

Have any pics of them installed?

Thanks. I knew the difference after searching online last night. Now I just need to pull a wheel off to see. I think I have the 10.5 ring gear but I will check tonight.

Also, I've heard many different reviews of the brackets from bent ones to striaght ones with spacers. I assume that you would recommend the ones you sell. But has anyone had any problems with either. Just wondering. Still gonna get yours though. Thanks

In theory bent is stronger, but the spacers are small and the difference in strength isn't worth noting.

Well I found out last night that I have a Semi Floater. Damn I was wishing that I had a FF. So do I still need to remove my axles inorder to get the hub off to do this. I've tried looking around the web and couldn't find out. I know that I don't have to remove them to take the drums off. Man I wish I had a FF. The install seemed so straight forward.

Well I found out last night that I have a Semi Floater. Damn I was wishing that I had a FF. So do I still need to remove my axles inorder to get the hub off to do this. I've tried looking around the web and couldn't find out. I know that I don't have to remove them to take the drums off. Man I wish I had a FF. The install seemed so straight forward.

yes

btt

How wide would it make a srw 14bolt compared to stock? I have a drw dana 60 front with uncentered h1s and wanna make it close to that width as possible.

How wide would it make a srw 14bolt compared to stock? I have a drw dana 60 front with uncentered h1s and wanna make it close to that width as possible.

Brake kits don't change the width of the axle. You need to get spacers to do that.

Thanks for all the orders recently.

money sent

Hoping to see my Ford kit soon :D Thanks again, great price :)

money sent

You may have already answered this 50 times but is there a difference in a full float dana 60? I have not tore into my axle and I am not sure what year it is or even what it came out of. Chevy or Ford... Also are you set up to take credit cards yet or are you still working with paypal and money orders only. I do not have a pay pal account and the postal service in my area likes to loose things for years. Let me know thanks one way or another I will end up with what you have here and very soon. Have to be back on the road by mid september no other options.

You may have already answered this 50 times but is there a difference in a full float dana 60? I have not tore into my axle and I am not sure what year it is or even what it came out of. Chevy or Ford... Also are you set up to take credit cards yet or are you still working with paypal and money orders only. I do not have a pay pal account and the postal service in my area likes to loose things for years. Let me know thanks one way or another I will end up with what you have here and very soon. Have to be back on the road by mid september no other options.

full float can take the axle out without taking off the brakes http://www.askjeffwilliams.com/uploads/Image/GM%20install%20axle.JPG

semi float you cannot and looks quite different. http://www.venturesparts.com/uploads/images/Semi_Floating_Axle.JPG

I do not take credit cards other than paypal. It's easy and free to set up with them. I can take walmart money transfer. You might consider priority mail if you are worried about it being lost.

Bump for a sweet deal!

sorry didn't read pages 4,5,6, & 7 so forgive me if it's been asked already.

how much for kit without rotors and calipers?

sorry didn't read pages 4,5,6, & 7 so forgive me if it's been asked already.

how much for kit without rotors and calipers?

It's ok. :) That saves $45 for the rotors and $45 for the calipers.

How much for just the Eldorado calipers, with Ebrakes?

Shipped to 18330.

Thanks.

Chris

How much for just the Eldorado calipers, with Ebrakes?

Shipped to 18330.

Thanks.

Chris

Let me check inventory and get back to you on that one.

btt

Do you have or can you make brackets for the skinnier mount later el dorado calipers? 5.5" bolt centers instead of 7"? Got what were supposed to be matched calipers and brackets off the classies and instead of spending a ton on the early calipers i'd like to get the brackets instead.

Do you have or can you make brackets for the skinnier mount later el dorado calipers? 5.5" bolt centers instead of 7"? Got what were supposed to be matched calipers and brackets off the classies and instead of spending a ton on the early calipers i'd like to get the brackets instead.

I don't but the guys at ruffstuff probably can.

btt

have any kits for 79 ford dana 60 in stock?

thanks CJ

have any kits for 79 ford dana 60 in stock?

thanks CJ

yes

PM sent.

That D60 kit will really help me out with getting my FF D44 done.

3 orders today and it's still early. Thanks!

btt

paypal sent

Thanks

Cj

Paypaled ya some money!

Thanks!
Rick

so is it only $315 including shipping? or is it more after shipping?

so is it only $315 including shipping? or is it more after shipping?

$315 includes shipping

that sounds like an amazing deal, i ought to buy a set for my 79 f250 after i get a good running motor in it

excuse the dumb question if it was covered before, but what style rotor does the 2nd gen 14BFF kit come with? the rotor thinkness, diameter, etc... is it the same as a front rotor would be?

pm me, getting money together for one of these kits :D

excuse the dumb question if it was covered before, but what style rotor does the 2nd gen 14BFF kit come with? the rotor thinkness, diameter, etc... is it the same as a front rotor would be?

pm me, getting money together for one of these kits :D

Everthing I use is from an 1980 Chevy 3/4 ton 4x4 front except the rotor for a sterling kit.

Sorry if this had been covered already, but is there a price difference in the weld on kit for a C&C 14 bolt? Wouldn't need the bracket spacers or grade 8 mounting hardware. I personally don't need the inner hub seals either if that would result in any savings. Thanks!

Pm sent

Do you have kits for 79 ford dana 60 with el dorado calipers in stock?

Do you have kits for 79 ford dana 60 with el dorado calipers in stock?

yes

Have any pics of them installed?

X2, on a 1st gen 14 bolt would be great :smokin:

X2, on a 1st gen 14 bolt would be great :smokin:

Not a 14B but a D44 with D60 ends that I just built.

http://i149.photobucket.com/albums/s63/jeeping1974/buggy%20build/NewImage.jpg

Pretty much looks like that.

Thanks for all the recent orders.

needin just loaded brakes and rotors shipped to 92530 thanks chris:smokin:

needin just loaded brakes and rotors shipped to 92530 thanks chris:smokin:

$240 shipped

Paypal sent 5 minutes ago for a $315 disc brake kit for a Chevy 14 bolt. :D

btt

I have a C&C, but already have bent brackets. My understanding is the hubs and mounting plate are the only difference. So with the correct brackets your kit should work, correct?

I have a C&C, but already have bent brackets. My understanding is the hubs and mounting plate are the only difference. So with the correct brackets your kit should work, correct?

Yep, take off $40 without the brackets on my kit. Everything else will work.

Just wanted to give a bump to this thread :):) I ordered the 2nd generation 14 bolt kit and not only did GubNi ship it the very NEXT day but the kit fit PERFECTLY!! During the install I THOUGHT I would be making at least 1 trip to the parts house for SOMETHING but I was WRONG!! 100% Plug and Play!! Great kit, Great Price, Great Service!!!
Thanks!!

PM sent good sir

do you know if there is any difference between the front 3/4 ton calipers and elderado calipers when it comes to piston area, clamping force, and overall performance?

or is the elderado caliper basicly all the same with just parking brake ability?

Just wanted to give a bump to this thread :):) I ordered the 2nd generation 14 bolt kit and not only did GubNi ship it the very NEXT day but the kit fit PERFECTLY!! During the install I THOUGHT I would be making at least 1 trip to the parts house for SOMETHING but I was WRONG!! 100% Plug and Play!! Great kit, Great Price, Great Service!!!
Thanks!!

Still waiting on mine.

Still waiting on mine.

Got my brakes saturday, everything looks great. Can't wait to get them installed, thanks for the help and great communication.

I have rotors, eldo calipers, and brackets. How much am i looking at for the rest of your kit shipped?
Also, can you send me a pm or email (rojam6133@live.com) of your lever and how i would hook it up on a jeep TJ. And are the levers available for purchase?

I have rotors, eldo calipers, and brackets. How much am i looking at for the rest of your kit shipped?
Also, can you send me a pm or email (rojam6133@live.com) of your lever and how i would hook it up on a jeep TJ. And are the levers available for purchase?

PM sent.

just got off the phone with PayPal...looks like the "Send Money" option is not working....they said that if you send me a PayPal invoice I can pay you that way. My email is aemerson1000 at gmail dot com.

73-87 chevy single rear wheel full floater 14 bolt axle 10.5" ring gear

just got off the phone with PayPal...looks like the "Send Money" option is not working....they said that if you send me a PayPal invoice I can pay you that way. My email is aemerson1000 at gmail dot com.

73-87 chevy single rear wheel full floater 14 bolt axle 10.5" ring gear

paypal request sent

paypal request sent


PayPal sent!

I have a 79 Dana 60 full floater, this will be a direct bolt on correct? Any suggestion to what proportion valve to use. Will be placing my odered after the holiday, Christmas killed me.:(

I have a 79 Dana 60 full floater, this will be a direct bolt on correct? Any suggestion to what proportion valve to use. Will be placing my odered after the holiday, Christmas killed me.:(

Yes, direct bolt on. With my kit I suggest you use the stock porportioning valve.

PayPal sent!


let me know when your shipping it out....

let me know when your shipping it out....

PM sent.

Is shipping still the same to 98387? thanks

Is shipping still the same to 98387? thanks

Yep, anywhere in the lower 48 states.

I'll probally have to wait till the 15th of January since christmas kind of broke me.

Do you have to upgrade your mastercylinder and Proportioning Valve for this or can you still run the stock stuff?

Do you have to upgrade your mastercylinder and Proportioning Valve for this or can you still run the stock stuff?

My calipers work best with stock portioning valve. Most applications the mastercylinder is fine.

ok sounds good ill let you know when i have the cash it should be on the 15th i wish i could do it sooner.

Hi Shawn, just sent you paypal for a disc brake kit.

Hi Shawn, just sent you paypal for a disc brake kit.

Thanks Pete - got it.

Shawn, any more kits with El Dorado calipers available 76' 14ff. Also, taking credit card #'s by phone yet?

Shawn, any more kits with El Dorado calipers available 76' 14ff. Also, taking credit card #'s by phone yet?

Yes and no in that order. :)

I am working on a website to pay by credit card, but it's not up an running yet.

Yes and no in that order. :)

I am working on a website to pay by credit card, but it's not up an running yet.

money sent thanks robin

PM sent. Check Sent.

Got my stuff, looks good, thanks Shawn

As soon as i can get my paypal account working i will send you some money.

just wanted to check, do you use the stock drum studs for the disc brakes?

just wanted to check, do you use the stock drum studs for the disc brakes?

Correct, reuse the stock studs for all kits except the semi float 14 bolt which I include new studs

Just checking on shipping date?

Just checking on shipping date?

PM sent

I am in need of the Sterling kit for my 97 -f-350. Tell me how to pay. I do have a Paypal account.
Thanks,
Steve

I am in need of the Sterling kit for my 97 -f-350. Tell me how to pay. I do have a Paypal account.
Thanks,
Steve

Pm sent

btt

hey shawn i just sent you paypal for my diskbrake kit.

pm sent

Got my kit today very nice can't wait to put it on

hello i called you the other day, could you let me know when you get that shipped out. either on here or by phone, if you still got my number. again it was a semi floater 14 from a 88 1/2 ton 6 lug.
chris from illinois
thanks

hello i called you the other day, could you let me know when you get that shipped out. either on here or by phone, if you still got my number. again it was a semi floater 14 from a 88 1/2 ton 6 lug.
chris from illinois
thanks

Will do