: Branik high steer arm special
BranikMotorsports 01-16-2009, 08:17 AM QUALITY DANA 44 AND DANA 60 High Steer Arm Special:smokin:
quality 1018 steel arms with correct angle alighnment.
compatiable with REID Racing Knuckles (extra bolt locations)
Will work with Stock knuckles.
Right and Left sets with stud kits
D44-$180.00 per pair- reg.-$220.00
D60-$260.00 per pair- reg.-$300.00
D60- double ended HSA-$185- reg-$200
THIS IS PIRATE 4X4 SPECIAL ONLY.
MUST MENTION THIS THREAD FOR DISCOUNT
BranikMotorsports 01-22-2009, 05:12 AM ttt
Dr Dino 01-22-2009, 10:19 AM ttt
botiejeep 01-23-2009, 09:55 AM How much for 1 double and 1 regular with Chevy 1 ton TRE to 81401. I also do not need the stud kit if that makes it cheaper
BranikMotorsports 01-26-2009, 06:05 AM pm sent, thanks
Marc Daniels 01-29-2009, 01:26 AM How thick are the arms where the tres mount? Thanks
BranikMotorsports 01-29-2009, 05:22 AM THICKNESS @ TRE = 3/4"- 4years no failures
John00TJ 01-30-2009, 07:27 PM Got any highsteer arms that clear humvee wheels whitout spacers for a dana 44 ??
rubberbelly 01-30-2009, 08:51 PM Got any highsteer arms that clear humvee wheels whitout spacers for a dana 44 ??
x2
Just got pitbulls on H2 rims and the TRE hit the tires :(
I'll take some measurements tomorrow.
BranikMotorsports 01-31-2009, 09:35 AM John00tj & rubberbelly, get US some drawings or pics and I will make some!
WE CAN MACHINE ANYTHING! well most anything!
BranikMotorsports 02-01-2009, 12:13 PM bump
lojones 02-03-2009, 06:39 PM dana 60 pair for 3/4 heims to 98027 please.
thanks!
cavaliers1323@aol.co 02-03-2009, 06:53 PM so glad i just spent way more than that on a set of competitors, bump for a good price!
BranikMotorsports 02-04-2009, 05:36 AM pm sent
seanyounk 02-05-2009, 12:03 AM I noticed two other guys all ready asked about this. Are you making any that will fit a Dana 44 with the stock Hummer H1 wheels. they are a 16.5 inch wheel with a 7 inch backspacing. The stock arms cause the Tie Rod end to rub. I ground off the Tie rod to the point of leaking grease and it still rubs a little bit. If you get some that will work I definitely want a set. Have you got the measurements you need yet? How much would it cost for a pair, with mounting hardware, shipped to 97305?
I would also like to know if you can put the 8 or 10 degree angle in the end for the tie rod end hole? It seems like most other guys swear by this practice. I cannot tell if they do all ready or not from the picture.
BranikMotorsports 02-05-2009, 05:49 AM we are going to have an answer today 2/5/09 about using these w/ h1 wheels
jpeater 02-07-2009, 08:54 AM Do these come with the 10 degree taper at the end? If so I need quote for pair of arms for Dana 44 with Reid knuckles for GM 3/4 ton TRE taper to 77494.
Also need the center line distance from tie rod to drag link holes on passenger arm.
Thanks for the offer, great price!
BranikMotorsports 02-09-2009, 05:58 AM these arms come std. w/ 5/8" tre hole, we can at
no charge make them tapered tre hole.
distance between 2 link holes is 2"
84thumper 02-15-2009, 08:23 PM Is there enough room too drill the holes out from 5/8 to 3/4 too run 3/4 in heims? looking too buy some for my chevy dana 44.
Thanks
adam
BranikMotorsports 02-16-2009, 06:17 AM plenty of room, we can do it for you if you want!
Captain Spaulding 02-18-2009, 08:06 AM dana 60 kingpin pair for 5/8 heims shipped to 42408
BranikMotorsports 02-18-2009, 08:28 AM Shipping in the lower 48 for $10 flat rate.
Dusty 02-20-2009, 04:03 PM Need a price for passenger side only, kingpin D60, drilled to 3/4", shipped to 92284. Thanks!
BranikMotorsports 02-21-2009, 10:32 AM pm sent
84thumper 02-23-2009, 10:14 PM Just got my dana 44 arms in today and must say GREAT Service and products, needed my arms drilled out too 3/4 for heims and they so no prob can do and did a great job and cant beat the price and even came with 6 new studs.
Ive recomended you too several friends hope too send you more busigness.
Heres some pics of my arms i recieved today look great!:grinpimp:
http://i197.photobucket.com/albums/aa159/thumper1986/89%20wrangler%20build/102_2434.jpg
http://i197.photobucket.com/albums/aa159/thumper1986/89%20wrangler%20build/102_2435.jpg
Thanks again
adam
wv85bronco 02-24-2009, 06:37 AM dana 60 kingpin
2 arms ...
Chevy TRE Taper
2 holes on passenger side
1 on driver (unless they already have 2)
shipped to 26452
thank you
BranikMotorsports 02-24-2009, 07:24 AM Pmsent
Elioknight 02-25-2009, 05:33 PM Dumb question, but do they come with conical washers with the studs? If so, could you PM me the price quote for a set of dana 44's with chevy TRE's to 44656
84thumper 02-25-2009, 09:31 PM Check out my pics in my earler post for exact pics of what the dana 44 arms look like. But just too answer your question no they dont come with washers dont need them drilled too just fit tight down on the studs themselfs.
I dont work for this company thow im just speaking from my own exp, as i ordered some arms from them and they are well worth the money good quality parts and they will take care of you.
BranikMotorsports 03-03-2009, 08:04 AM the nuts are tapered to fit countersink in arms
and eliminate the need for conical washers.
no failures ever!
84thumper 03-03-2009, 07:51 PM wow i dident even notice the nuts were like that.Thats very smart thinking there putting the nut and the con washer and makeing it into 1 thing.
These keep getting better and better.
Almost got 1 side back together will take some pics later and post up of 1 installed.
BranikMotorsports 03-05-2009, 05:55 AM thanks 84thumper!!
BranikMotorsports 03-10-2009, 05:03 AM bump ttt
seanyounk 03-11-2009, 11:05 PM Sorry guys! we will see what he comes up with
BranikMotorsports 03-19-2009, 10:22 AM ttt
silverback97 03-23-2009, 07:41 AM What is the distance from center of ball joint to center of furthest hole.
and how much for two Dana 44 arms to 63389. just need the furthest hole on both arms reamed to fit chevy TRE.
thanks,
Matt
Twistedcrawler 03-23-2009, 08:23 AM Morning bump for ya'll...
Thanks again for the great work!
kf4zht 03-23-2009, 10:49 AM Do you have any kind of spacers for these? I need to clear leafsprings
BranikMotorsports 03-23-2009, 11:23 AM thanks pms sent
Twistedcrawler 03-24-2009, 06:39 PM Bump for the day
BranikMotorsports 03-31-2009, 02:18 PM bump
whiskey-7 04-07-2009, 10:07 AM Pair Dana 44 arms drilled for heim shipped to 97211
BranikMotorsports 04-07-2009, 11:53 AM Pair Dana 44 arms drilled for heim shipped to 97211
Through April 09, pair d44 HSA, with stud/nut kit, $170.00 + $11.00 flat rate USPS. thanks
BTW----H2 wheel guys, new design being tested, with the 44 hsa's
Results coming soon.!!!
BranikMotorsports 04-15-2009, 05:02 AM bump
2ndIINoneMotorsports 04-20-2009, 02:36 AM Passenger side dana 60 ford kingpin for a HEIM and a TRE. Shipping to 91042
BranikMotorsports 04-21-2009, 01:52 PM pmsent
BranikMotorsports 04-28-2009, 01:57 PM ttt
Tippy 04-28-2009, 09:00 PM Can I get a quote for a double and a drivers side single dana 60 please?
BranikMotorsports 04-29-2009, 05:10 AM pm sent
Twistedcrawler 05-04-2009, 09:39 AM Morning bump for ya'll
BranikMotorsports 05-18-2009, 11:54 AM Special pricing through july 2009
BranikMotorsports 05-26-2009, 02:46 PM ttt
rubberbelly 06-08-2009, 03:04 PM bump, sent you an email... I'll give you a ring tomorrow.
cperry 06-08-2009, 07:09 PM Branik Boys will be back in the shop Tues, they were laying down the hammer at XRRA. 3 of them in the Top 6 impressive outing
BranikMotorsports 06-16-2009, 03:00 PM ttt
flatlander757 06-16-2009, 08:01 PM So I boogered up my stock high steer arm on my kingpin D60, need a single arm for the passenger side ready for a 3/4" bolt heim.
Also I need this ASAP... how quickly could it be sent out? I've got a short time before my build needs done and I need the steering set up before I make the trackbar.
-Tony
BranikMotorsports 06-17-2009, 04:55 AM thanks pmsent
Bigburlynakedguy 06-17-2009, 06:44 AM I need a passenger side only 44, stock knuckle, draglink undrilled?
BranikMotorsports 06-17-2009, 07:20 AM thanks
BranikMotorsports 06-19-2009, 05:46 AM thanks for the orders!
flatlander757 06-20-2009, 08:16 PM Hey Stan thanks again for the fantastic service! Got my steering arm today, it looks :smokin:
BranikMotorsports 06-26-2009, 05:27 AM thanks
BranikMotorsports 07-06-2009, 03:40 PM we have all high steer arms in stock.
howyadoin 07-06-2009, 11:34 PM Price for D60 "steering behind axle" pair with double arm on driver's side (single arm to rear) for Reid knuckles to 85383. Thanks, ready to order, just cracked my current home fab arm!:shaking:
BranikMotorsports 07-07-2009, 07:12 AM pm sent
SPIDERSURF 07-07-2009, 07:37 PM Do you have a design to fit the dana 44 with h1 wheels?
BranikMotorsports 07-09-2009, 12:31 PM we have turned bolt pattern to clear the h1 wheels.
design the same, just rotated mtg. bolts to clock arm in.
rubberbelly 07-09-2009, 12:51 PM Do you have a design to fit the dana 44 with h1 wheels?
Hey Stan,
When will mine set be shipping out?
Thanks,
Jason
marine_mike 07-09-2009, 01:03 PM Interested in the turned high steer arms for a HD HP Ford D44 with stock H1 wheels to zip 48051. Pics too if you can provide them.
TornadoTJ 07-09-2009, 01:26 PM we have turned bolt pattern to clear the h1 wheels.
design the same, just rotated mtg. bolts to clock arm in.
For 91 Ford D60 also? I believe the original question was for D44. HSA's fit as well?
BranikMotorsports 07-16-2009, 05:19 AM working on a d60 / h1 version.
jwjeep1 07-16-2009, 08:18 AM Interested in a D44 single passenger side, tapered to fit a stock CJ TRE if possible, shipped to 81650. Thanks.
BranikMotorsports 07-28-2009, 06:20 AM thanks
BranikMotorsports 08-20-2009, 05:33 AM ttt
jason79cj7 09-05-2009, 03:00 PM What is the price for a set of high steer arms for gm dana 44 knuckles shipped to 45044?
need them for tre's
turbomustang 09-05-2009, 06:19 PM dana 60 arms ford for tre;s
BranikMotorsports 09-28-2009, 05:41 AM thanks
solidrunner 09-29-2009, 10:02 PM Can I get a price on a passenger side arm with a stud kit shipped to 98166. Thanks
BranikMotorsports 09-30-2009, 05:17 AM pmsent
tnjeep 09-30-2009, 05:33 PM On the 60 arms what is the distance from the center of the kingpin to the center of the last hole.
BranikMotorsports 09-30-2009, 05:40 PM 7 seven inches
wearethebucs 10-04-2009, 08:03 PM Can I a quote for a set of arms for Ford 44 knuckles with 5/8" holes for heims.
BranikMotorsports 10-05-2009, 05:19 AM pmsent
fuzzydog 10-05-2009, 02:35 PM Do you ship to Canada, eh?
quote for D44 arms to V2G 1R1
I prefer USPS for shipping
BranikMotorsports 10-05-2009, 03:24 PM Of course we do, as a matter of fact,
we ship all over the world!
pm coming your way thanks.
BranikMotorsports 10-23-2009, 06:54 AM in stock
BranikMotorsports 11-09-2009, 01:44 PM prices are still good!
mechanicalmongoose20 11-09-2009, 02:21 PM Quote 2 of your H1 rotated dana 44 arms kits, also include milling and drilling of the knuckles, i'll bringem up to you guys. Also, i already have balljoints pressed in, how much to pressem out? or is it free if i buy the kit and have you guys do the machine work too? :D Thanks fellas.
Jamz527 11-09-2009, 02:40 PM When, or if available when do you think you will have the ford kingpin dana 60 model out with the stock backspacing of the H1 wheel
BranikMotorsports 11-11-2009, 05:42 AM we have a pattern now to do the h1 offset.
made to order.
BranikMotorsports 11-18-2009, 07:56 AM all in stock!
BranikMotorsports 11-20-2009, 02:42 PM get some
BranikMotorsports 12-03-2009, 07:42 AM ttt
BranikMotorsports 12-09-2009, 05:14 AM bump
BranikMotorsports 12-22-2009, 05:17 AM ttt
BranikMotorsports 01-04-2010, 05:18 AM new years bump
jessejeepin 01-04-2010, 10:04 AM we have turned bolt pattern to clear the h1 wheels.
design the same, just rotated mtg. bolts to clock arm in.
Need a price on 2 arms for stock 44 able to clear h1 wheels
BranikMotorsports 01-04-2010, 11:46 AM pm sent, we also make d60 hsa's for the h1 rims.
BranikMotorsports 01-12-2010, 05:11 AM Ttt
BranikMotorsports 01-15-2010, 04:49 AM ttt
BranikMotorsports 01-20-2010, 07:59 AM thought we made plenty ahead...but gotta make some more:grinpimp:
we have a few sets left, gonna try to NOT run out!
BranikMotorsports 01-25-2010, 04:56 AM thanks for the orders!
BranikMotorsports 01-30-2010, 11:29 AM ttt
BranikMotorsports 02-17-2010, 01:01 PM ttt
BranikMotorsports 03-04-2010, 03:03 PM bttt, all in stock!!!!!!!!!!!1111
crazyredneckanyhow 03-05-2010, 08:37 PM Price on just a drivers side KP 60 are tappered for gm tre. Shipped to 26582
Thanks
BranikMotorsports 03-06-2010, 09:32 AM pmsent
Dr Dino 03-16-2010, 01:17 PM bump
BranikMotorsports 03-24-2010, 04:59 AM ttt
pm me a quote for one regular and one reverse arm to 66062. thanks
BranikMotorsports 03-30-2010, 11:41 AM thanks
azxj1 04-07-2010, 09:58 PM price on just the passenger side arm and hardware for a ford Dana 44 shipped to 85396
BranikMotorsports 04-17-2010, 05:39 AM pmsent
BranikMotorsports 04-22-2010, 06:17 PM ttt
Mopar96 04-24-2010, 04:05 PM d44 left-right and studs shipped to 45805
BranikMotorsports 04-24-2010, 05:03 PM thanks
Rinkrat456 05-07-2010, 07:35 PM Free bump for ya and a question as well.
Looking for a passenger side D44 high steer arm for H1 wheel specs shipped to 55805. I have read other H1 steering arms having trouble with weights being clipped to the inside of the rim. Has this been solved with Branik's arms?
My pitman arm is 7" from center to center. Will this match the high steer arm?
Johno33772 05-07-2010, 08:20 PM Dana 44 set shipped to 33772
THX
BranikMotorsports 05-10-2010, 02:56 PM pmsent
BranikMotorsports 05-18-2010, 06:09 AM to the top
fuzzydog 05-18-2010, 11:28 AM Got my arms today - Thanks Stan!
only took 1 week to get from Ft Wayne, In to my door in Williams Lake, BC, Canada
paid $14 and change GST
Entire transaction went smoothly (even though I took my time getting the order in after getting the quote :emb4:) and the product is :smokin:
Mopar96 05-19-2010, 02:29 PM Bought my arms from these guys last week. Got them to me when they said they would. You guys are awesome!! Cant thank you enough. Ill have to stop by the store sometime since its only an hour away.
-Mike
BranikMotorsports 05-24-2010, 04:28 PM thanks guys!
BranikMotorsports 06-14-2010, 02:35 PM ttt
crazyredneckanyhow 06-20-2010, 06:43 PM Change in the project. D44 arms to 26582 thanks
BranikMotorsports 07-01-2010, 05:26 AM pmsent
BranikMotorsports 07-07-2010, 10:58 AM ttt
BranikMotorsports 07-22-2010, 01:03 PM ttt
bigchevytruckdriver 08-01-2010, 02:20 PM Shoot me a price for L and R on Dana 44. Shipped to 95965. 1 ton tie rod if possible.
BranikMotorsports 08-02-2010, 07:17 AM thanks pm sent
BranikMotorsports 08-23-2010, 02:30 PM ttt
BranikMotorsports 09-10-2010, 11:54 AM in stock. std. d44 NEVER RETURNED!!
H1- mod. in stock!
BranikMotorsports 09-14-2010, 01:00 PM ttt
BranikMotorsports 10-26-2010, 05:21 AM ttt
BranikMotorsports 11-17-2010, 05:31 AM ttt
BranikMotorsports 11-29-2010, 05:11 AM bump
GAwheeler 12-01-2010, 07:31 PM Price on a set of Ried knuckles, your arms set up for high steer, and all hardware for a chevy 44 shipped to 30011 please!
BranikMotorsports 12-14-2010, 05:19 AM thanks for the orders,
wilco 12-21-2010, 12:04 AM price for just a single passenger and double driver dana 60 arms without hardware to 95452
BranikMotorsports 03-11-2011, 06:14 AM ttt
BranikMotorsports 03-21-2011, 08:09 AM fresh lot now in stock!!!
backorders on their way!!!!! THANKS for the business!
BranikMotorsports 04-29-2011, 04:59 PM ttt
BranikMotorsports 06-01-2011, 05:33 AM the d44 arms are H1 wheel ready!!!!!!!!!!!
BranikMotorsports 06-13-2011, 12:02 PM ttt
BranikMotorsports 06-20-2011, 02:08 PM ttt
Tippy 06-21-2011, 08:09 AM sent you a PM...looking for a set of 1" spacers to fit your D60 arms.
Thanks.
BranikMotorsports 06-22-2011, 05:11 AM thanks
beelzebuba 06-23-2011, 10:49 PM will your arms clear H2 wheels on a ford 44? 3/4 ton TRE's, 59740 thanks.
BranikMotorsports 06-28-2011, 05:07 AM YES, our d44 arms will Now clear hummer wheels and tires!
BranikMotorsports 07-28-2011, 02:29 PM plenty in stock.
never had any failures
BranikMotorsports 08-04-2011, 09:16 AM ttt
BranikMotorsports 08-26-2011, 05:35 AM ttt
97FrankenHeep 08-31-2011, 10:13 AM Price on D44 arms for H2 wheels with 1 Ton Chevy TRE taper, shipped to 94551.
BranikMotorsports 09-07-2011, 10:29 AM thanks for the order.
BranikMotorsports 09-28-2011, 11:48 AM bump
BranikMotorsports 10-05-2011, 10:26 AM ttt
BranikMotorsports 10-17-2011, 05:22 AM ttt
85K5DSL 10-22-2011, 06:49 PM Price on a pair of D44 arms drilled for TRE's & set of stud ? All your arm clear stock H1 wheels correct ?
Thanks
BranikMotorsports 10-26-2011, 05:51 PM thanks,
and yes they fit H1
85K5DSL 10-27-2011, 05:05 AM PM sent
BranikMotorsports 11-17-2011, 08:49 AM thank you!
BranikMotorsports 12-16-2011, 08:19 AM ttt
| |