Our Latest D60 Full-Hydro Steer Arms

http://www.northwestfab.com/images/steering/d60hydro2.JPG

Same Great Features As Our Crossover Arms:

- 100% CNC Machined From 1810 Billet Steel Stock.
- Can Be Mounted Forwards or Reverse for Ram Flexibility
- Kingpin Pre-load Adjustment via 1" Set Screw
- Grease Zerk Fitting On Top For Ease Of Maintenance.
- Arm Geometry Adjusted For Steering and Kingpin Axis Inclination Angle.
- Tapered For Tie Rod Ends or Drilled For 3/4" Heims.
- 5th and 6th Hole for Aftermarket Reid Racing Knuckles.
- Compatable with our new Upper Kingpin System


http://www.northwestfab.com/images/steering/d60hydro1.JPG


http://www.northwestfab.com/images/steering/d60hydro3.JPG

With Some Added Features:

- Designed with cues from Sean 'Station' @ Performance Offroad Steering To give the best ackerman angle possible.

- Long enough to handle the proper length 8" DE ram for a D60 for maximum leverage.

- 1 1/4" Thick! [ not 1" like the rest of our competitors ]

We stock them blank, we can drill them for you at no extra cost! or ship them blank - it's up to you! (98% of the time the hole will be 8" From center for proper ram throw).

$ 135 each !

We also stock high strength chromoly installation studs ($29 / 4 studs and nuts)!

Give us a call to get yours ~ 250 248 6024.

Thanks.

BTT Lots of Stock !

Bump !

Thanks for the orders. PM's returned.

What material are you guys using?

good stuff btt

What material are you guys using?

1018 billet steel.

Could these be made to be compatible with a set of Solid knuckles with their keyway? I would think it would be easy/possible to mill out the slot for the keyway, but what about the bolt layout? Do they share the same 6 bolt layout?

Could these be made to be compatible with a set of Solid knuckles with their keyway? I would think it would be easy/possible to mill out the slot for the keyway, but what about the bolt layout? Do they share the same 6 bolt layout?

The pattern is the same as the solid knuckles. Either we can mill the keyway in, or the key would have to be milled off. Obviously milling the key in is preferable.

The pattern is the same as the solid knuckles. Either we can mill the keyway in, or the key would have to be milled off. Obviously milling the key in is preferable.

Awesome!!! PM coming your way.....

Awesome!!! PM coming your way.....

pm sent back your way

Bump!!!

Just finishing up a new batch order yours today!!!

In Stock!!!

Lots in stock ships the same day!

do you have 4 studs with tapered nuts in stock?

thanks

do you have 4 studs with tapered nuts in stock?

thanks

Yes

In stock and ready to ship!

TTT lots in stock.

Bump

In stock and ready to ship.

Will they clear stock H1s?

Will they clear stock H1s?


No they will not. The only steering arms that will are our raised arms. We do make a long raised arm for the driver side that is a mirror image of the passenger side, this will allow you to run stock H1's and full Hydro.

Kris

Almost finished Machining a new batch of arms, should be able to ship by the end of the week.

In Stock and Ready to Ship!

10 Pairs in stock, ship same day.

We still have lots in stock!!

We currently have 7 Pairs available, and are ready to ship.

Get 25% off stud kits when purchased with a set of Full Hydro Steering Arms

Lots instock!!!

10% off Full Hydro Arms until th1 End of October!