i just got back from a week in gatlinberg (vacation), where i got some new winch parts (hook, thimble, cable clamps), and when we got here i found that the Sniper Fabworks boot gaurds, and the new neoprene boots were here also... JOY! :D fixed the winch and will tear into the front end tomorrow. what about you?

worked friggin 13 hours !!!! just means more money for parts !!! still need a 435 though ANYBODY WILLING TO DONATE ????

Picked this up for $1200, pretty good deal here in FL.
'88 B2: 36s, d44/9", 56k miles, 2.9l V6 auto
http://images.craigslist.org/3k73od3p2ZZZZZZZZZ96r2e85f3038bea10a5.jpg
Worked all day cleaning it(was a mud truck) :)

Threw a new pilot bearing in my flywheel, locked up on me this morning and damn near rear ended a car in front of me at the intersection I was coming to when it kept driving.....

3 hrs from start to finish, no lift, no help.....not bad I think?

I went wheelin today......:flipoff2::flipoff2::flipoff2::flipoff2 :
Started at 4:00 AM and went home around 1030AM. Gets a tad hot here.

I went wheelin today......:flipoff2::flipoff2::flipoff2::flipoff2 :
Started at 4:00 AM and went home around 1030AM. Gets a tad hot here.

you suck! i wanted to go ridin today too, but i knew i would get back too late to meet up with the guys i wanted to ride with... there was a group from rebelrockrunnners.org and TnCrawlers.com ridin at windrock today, and ive been wanting to meet up with these guys for a while. :(

Picked this up for $1200, pretty good deal here in FL.
'88 B2: 36s, d44/9", 56k miles, 2.9l V6 auto
http://images.craigslist.org/3k73od3p2ZZZZZZZZZ96r2e85f3038bea10a5.jpg
Worked all day cleaning it(was a mud truck) :)
Got more pics of that?
Looks pretty sharp! Nice buy. :beer:

Got more pics of that?
Looks pretty sharp! Nice buy. :beer:

Tomorrow I will.
36x16.5r15 DC FCs that are worn and need replacing up front on some nice 15x14 aluminum wheels
EB D44 with stock discs/Ford 9" BB with stock discs(i think) with stock 3.08s... Yeah I know:flipoff2:
Eb 4" coil up front with stock arms and drop brackets, some chevy 3/4 ton spring out back that are hard as hell with a horrible shackle angle
medium to low rust on the body only
squishy brake pedal...with a hole in the brake cap:shaking:
Its beat but for $1200 you can't complain:grinpimp: And the flowmaster muffler sounds good too!:smokin:

Hauled in 2 loads of topsoil, spread it and rolled it. Setup lawn watering system. Dug trench for wire of dog's shock collar thing, but ran out of wire (only had 500ft in the kit) Lowe's run for parts, test drove a car, called my Mom, cut some firewood, did some laundry and swept/vac the floors in the house.
Probably going to finish my garage floor epoxy tonight and then put the stainless doors on my fridge.
Was hoping to get more stuff done but I only got up around 7:30.

put new brake pads on my dads car. replaced a rusty broken body mount on my 94 ranger so the body wont hit the fan and over heat. that sucked. mowed half the lawn and blow the f*cking engine in it:mad3:. dont ask me how it just happened. got pissed so i took the ranger down the old level b road threw some mud around:D. i found out the new body mount works. thats about it gonna organize the garage in the morning. nite yall

I tried to trade my '90 Chevy truck for a '77 Ford F-150 Supercab with a 460, and the guy tried to change the deal, so I left. Came home (2 hour drive) and put the truck on Craigslist for $1800 or trades, and in ten minutes I got a call from someone who offered a Honda 185 ATC 3-wheeler and a Arctic Cat 4x4 ATV for trade. Both are now sitting in my driveway, and I am rid of that GM garbage forever.

Cardone saginaw pump.

YouTube - saginaw pump (http://www.youtube.com/watch?v=F9qTCxf85GI)

today i finished up fabing the winch mount, mounted, wired and tested the warn 8274... good to go! :smokin:

Well I cobbled my junk back together. Now my ranger has a square tube front driveshaft and the transfer case side is tack welded in so it lets the tube slip and doesnt leave me hung up and stuck in 2wd again. BTW I did say "cobbled" lol itll work it aint perty though.
Also welded my broken hock mount back on ready to go wheelin and break something else now.

swaped the old dry rotted, shreaded, rubber knuckle boots with new yellow neoprene boots and installed the new boot guards... :smokin:

almost ready for another ride!

Worked all day finding errors in the next software release for my companies medical diagnostic devices.

I am glad I don't write the code :shaking: I just find the bugs:evil:

I can not wait for this validation and verification to be done it sucks brain cells and I will need to replace with high octane spirits to fix again tonight!!

Much rather would be doing my real work as an electronics engineer
Or better yet out wheeling without work on the brain!!!!!

After I got home and relaxed I felt better so I went to work on my explorer. I removed the last of my ttb brackets and just about finished trimming the k member. Just about ready for it to roll out of the garage under it's own power. :smokin:

:eek: