do yall offer flat top milling

if so what would be the price of getting some chevy flat tops milled, drilled, and studs installed

thanks

Yes we can do them for $40 / pr. Thanks - Jeff

my driverside came from the factory done

so if i wanted to just to pass side, milling, and drill/tap its only 20 bucks?

$30 for one side. Thanks - Jeff

FYI, it is worth the extra $10 to get both done as they can be milled to the same hieght. A 16th or an 8th might not seem like a lot but when you look at your tie rod and you can see it is not parrallel with the axle tube it may bug the crap out of you. I had to put washer spacers on one side to get it right and even having the spacers bugs me. Maybe it's just me...

FYI, it is worth the extra $10 to get both done as they can be milled to the same hieght. A 16th or an 8th might not seem like a lot but when you look at your tie rod and you can see it is not parrallel with the axle tube it may bug the crap out of you. I had to put washer spacers on one side to get it right and even having the spacers bugs me. Maybe it's just me...

so we just ship to you and you ship back... thats a pretty good deal:smokin:

That's right

Jeff

sweet, i will hit you guys up... im goin hydro assist soon, so all i need is a flat top knuckle?

Can you do this to 99-04 Ford D60s?

http://i562.photobucket.com/albums/ss64/84sixty/CIMG0219.jpg?t=1254421210
http://i562.photobucket.com/albums/ss64/84sixty/CIMG0220.jpg?t=1254421252
http://i562.photobucket.com/albums/ss64/84sixty/CIMG0221.jpg?t=1254421293
http://i562.photobucket.com/albums/ss64/84sixty/CIMG0222.jpg?t=1254421348

I don't see wht not, but the price will goto $70 base due to reprogramming and fixture setup. If you can round up a few sets I will drop the price to the standard cost.

I don't see wht not, but the price will goto $70 base due to reprogramming and fixture setup. If you can round up a few sets I will drop the price to the standard cost.

http://gmfullsize.com/forum/images/smilies/Handshake.gif

Thanks!! I'll see what I can do.

How much for the arms?

Is there a set on the market already?

Is there a set on the market already?

No. :(

Here are some more ideas. I know one is from an 05+ Dan 60, and another pic is from a 92-97 D60. If at all possible, I would like to be able to double sheer the heim with the stock steering arm. I know the brakes are different for all years of the ball joint D60; 92-97 vs 99-04 vs 05+, but if you could figure out
a one size fits all ordeal, that would could costs down I'd assume.


http://i290.photobucket.com/albums/ll273/ruearmstrong/6014004.jpg
http://i290.photobucket.com/albums/ll273/ruearmstrong/6014bolt010.jpg



http://i53.photobucket.com/albums/g42/dozerdan_photos/Dana60swap067.jpg
http://i53.photobucket.com/albums/g42/dozerdan_photos/Dana60swap069.jpg
http://i53.photobucket.com/albums/g42/dozerdan_photos/Dana60swap074.jpg
http://i53.photobucket.com/albums/g42/dozerdan_photos/Dana60swap079.jpg
http://i53.photobucket.com/albums/g42/dozerdan_photos/Dana60swap087.jpg



http://i244.photobucket.com/albums/gg10/bsudder/DSC_0103.jpg
http://i244.photobucket.com/albums/gg10/bsudder/DSC_0102.jpg
http://i244.photobucket.com/albums/gg10/bsudder/Christmas07-Jeep032.jpg

Is there a set on the market already?

I lied. Just found these. But competition is good. :D

http://www.currieenterprises.com/cestore/Product.aspx?id=2936

Jeff, if you need a set of BJ knuckles, I might be able to work something out. I need to take my rig down after a certain event in 5 weeks to replace some inner axle seals and more than likely some other parts that will be "compromised".

Jeff, if you need a set of BJ knuckles, I might be able to work something out. I need to take my rig down after a certain event in 5 weeks to replace some inner axle seals and more than likely some other parts that will be "compromised".

What year model is your BJ60?

What year model is your BJ60?

95 Ford

95 Ford

:D Good then I can still send him my 03 knuckles. :laughing:

So I can ship you my 99SD knuckles and you will mill them flat, drill them, and install studs for about $70?

PM me your address and a paypal addy as well as a total cost!

THANKS

how much would you charge to get a pair machined and new ball joints pressed on? :D

So I can ship you my 99SD knuckles and you will mill them flat, drill them, and install studs for about $70?

PM me your address and a paypal addy as well as a total cost!

THANKS

What are you gonna do for arms? I guess we're in the same boat.

What are you gonna do for arms? I guess we're in the same boat.

Probably gonna torch out my own set if I can get BF to mill, tap and stud the knuckles.

What are you gonna do for arms? I guess we're in the same boat.

Again, if there is enough interest we can make a few sets.

-Jeff

Put me on the list as well. I have an 03 front 60 I would like this done:p

i would also like this done to 2 sets of '04 knuckles that i have.

Could you press on some new ball joints when I send the pair to get machined? if so How much would you charge?

you can put my on the list for a flattop BJ60 job with new BJ's also!!!

i don't know if this would be too much of a request or if you already do it but: can you machine a set of HP 44 knuckles with a key way and do you sell the high steer arms with the key way? kind of like the Sky set up, but i would much rather go with ballistic than sky.....

Not a problem at all, send them our way.

can you send me your address, payment info, and total cost for doing a pair of 44 knuckles, shipped to and from 27703 business address?

and what is the approximate turnaround time?

thanks!

do you have any idea on what the turn around time would be. im in va, so im guessing 3-4 days of shipping there

2-3 days depending on our schedule at the time. When you're ready to ship them let me know and I'll give you an accurate lead time at that point.

Jeff

can you send me your address, payment info, and total cost for doing a pair of 44 knuckles, shipped to and from 27703 business address?

and what is the approximate turnaround time?

thanks!

These types of deals need to be taken care of over the phone to avoid confusion. Lead time is 2-3 days as stated above.

Jeff

Final word on Pricing

Standard flat top mill job
40$ Pair
30$ Per Side

Add 10$ each with keyways

For keyways we will need the specs that you want. Balljoint 60's are 70$ per pair right now.

For further information or questions please call the shop at (520) 888-4441

Final word on Pricing

Standard flat top mill job
40$ Pair
30$ Per Side

Add 10$ each with keyways

For keyways we will need the specs that you want. Balljoint 60's are 70$ per pair right now.
For further information or questions please call the shop at (520) 888-4441

:D:D:D:D

What arms do these accept?
What year model of D60s?

Standard 4 bolt kingpin axles. We're working on further development for the balljoint 60's.

Final word on Pricing

Standard flat top mill job
40$ Pair
30$ Per Side

Add 10$ each with keyways

For keyways we will need the specs that you want. Balljoint 60's are 70$ per pair right now.

For further information or questions please call the shop at (520) 888-4441

Standard 4 bolt kingpin axles. We're working on further development for the balljoint 60's.
:confused::confused::confused:

Does that mean you typoed? or did I misunderstand....?

No, it means I can machine it to whatever you want, but I don't know if it will fit anything at this time. A conclusive setup from us is still in line for development.

ok, so i already have new ball joints pressed in, and its a ford D44 so the drivers is already done. How much to press out the ball joints( assuming you need to so you can face them) mill and drill/tap passenger side, mill and re-tap drivers side, and press ball joints back in? Also, can you give a print of the locations of said drilled and tapped holes? i'm going to make my own high steer arms without spacers, but an extra 2" to clear the leafs. Thanks

any chance that if i ordered the arm, and hardware kit at the same time as i got the milling done you guys could install the arm, or would there be added price

no big deal if not

what would be the total cost for ford hp44 78-79 (both) nuckles to be milled drilled tapped studs installed...as well as a set of arms....and if i ship you just the knuckles how much would the shipping be to have the arms shipped back with the knuckles...zip 97601....

what would be the total cost for ford hp44 78-79 (both) nuckles to be milled drilled tapped studs installed...as well as a set of arms....and if i ship you just the knuckles how much would the shipping be to have the arms shipped back with the knuckles...zip ....


to 32246 please and ty