PDA

: Bumper pics

scott-885
09-25-2002, 10:47 AM
These are a couple PICS of a bumper we built for a buddy of ours, Tell me what you think.
scott-885
09-25-2002, 10:48 AM
and one more
SMART ASS
09-25-2002, 10:55 AM
DECENT
BrettM
09-25-2002, 10:59 AM
I've seen a hell of alot better... but I've seen a hell of alot worse...
GO 4LO
09-25-2002, 11:01 AM
Looks good to me!
Chris
joes75bronco
09-25-2002, 11:37 AM
Originally posted by GO 4LO
Looks good to me!
Chris

I'll second that
Huff
09-25-2002, 01:20 PM
I like it.
CRUISERBOYFJ40
09-25-2002, 01:28 PM
Not to shabby:smokin:
MSB
09-25-2002, 02:55 PM
looks good
Bill Collins
09-25-2002, 03:22 PM
i will take one for a toyota that will hold my 8274.when it is done i will give you my address....
snowman75
09-25-2002, 03:47 PM
looks good!
1248bullitt
09-25-2002, 03:59 PM
Looks good.

Wes
scott-885
09-25-2002, 04:06 PM
Appreciate all the good feed back. Wish I had a front shot but I guess I deleted It. For anybody at Texas A@M you will see it
Has a skid plate on front and painted flat black. THANKS again


Scott-885
Rocksie
09-25-2002, 04:13 PM
looks good...One FYI comment though. If is sits right on the body (front fender) Or has little room keep in mind that it could get smashed into the fender via four wheeling...I've seen it happen the entire fender was fuked. But hey if it's not for that kinda wheelin then sweet!

Now you just need some fibergalss fenders.:flipoff2:
scott-885
09-25-2002, 04:19 PM
Believe it or not when building the bumper the same issue came up so we flexed the vehicle every way possibe to check and see where we were gonna hit. And all cleared. Of course Im sure a big enough rock could persuade the 1 3/4 DOM to act diffrently.
Rocksie
09-25-2002, 04:24 PM
Originally posted by scott-885
Im sure a big enough rock could persuade the 1 3/4 DOM to act diffrently.

Rocks do strange things;)
The Adam Blaster
09-25-2002, 04:56 PM
I can't tell from hte pics, but is it tied into each frame rail, or is it being supported only at one point?
scott-885
09-25-2002, 05:34 PM
Yes it is tied into the frame rails. We actually cut about a foot off the frame.
scott-885
09-25-2002, 05:35 PM
And the other side with down bar.
Pathmaker
09-25-2002, 10:30 PM
i dig it, good approach angle
K05Aggie
09-25-2002, 11:30 PM
It looks good. Maybe I'll get lucky and see it in person.
patcal19
09-26-2002, 02:50 AM
Looks like good work to me! Just one question. Where's the winch mount?
nobody20
09-26-2002, 06:53 AM
Looks good to me. Nice work. If I still had my F-350 I'd use it a model.
scott-885
09-26-2002, 07:37 AM
When he gets his winch we are going to make it a multi mount.
It will fit between the lights. I know it will stick out but its the way he wanted it.
broncorob
09-26-2002, 10:30 AM
Yep, looks nice