Come and get some of these... [Archive]

fatkid

10-02-2002, 07:32 PM

Originally posted by Rockrat
Sweet I like those drive shafts or lack of what happened to the bling bling aluminum locks

No Drive shafts till the tranny and T cases are in, and I still have the Champions. However the Locks are going to be sporting some 37" MTR's for Compition.

fatkid

10-02-2002, 07:34 PM

Originally posted by Bill4rest
Did ya fix the front yet? .

The front is getting a new tube frame and front clip in next few weeks. Should match the rear just right.

poppycock

10-02-2002, 07:43 PM

sweet! :grinpimp:

RE:Todd

10-02-2002, 07:44 PM

Lookin good Fatty, bringin it to FrostOberFest????

Mustard Dog

10-02-2002, 07:46 PM

Well it's lookin like Azrockrawler is gonna have to bust out his checkbook if he's gonna copy the fatkid again :eek:

poppycock

10-02-2002, 07:48 PM

:laughing:

fatty are you running 4.10s in your axles?

Pappa Smurf

10-02-2002, 07:48 PM

Originally posted by fatkid
Pic of the new Toy tranny with Ultimate T- Case set up, not to mention the SOS Ringer adapter.
:)

one question what is that thing beside it's the tranny and tcases what gears are you running in them

fatkid

10-02-2002, 08:00 PM

axles have Longfields with 5.29's
Toy tranny with double stack 2.28 and Marlin 4.7 gearset, final crawl is 223:1

zukiboy

10-02-2002, 08:04 PM

what width wheel are you goin to run the 37 mtr's on?.....i see that tire rack has some kick ass prices on 37's these days:D

fatkid

10-02-2002, 08:06 PM

I'd like to run them on a set of 15x10 Champions.

Bill4rest

10-02-2002, 08:27 PM

Originally posted by Mustard Dog
Well it's lookin like Azrockrawler is gonna have to bust out his checkbook if he's gonna copy the fatkid again :eek:

what's that soposed to mean?:confused:

Bill4rest

10-02-2002, 08:29 PM

Originally posted by fatkid
I'd like to run them on a set of 15x10 Champions.

do you have a Tin Bender named Pat? in the NAVY and has a red CJ5 or at least used to have.

Pappa Smurf

10-02-2002, 08:33 PM

Originally posted by Mustard Dog
Well it's lookin like Azrockrawler is gonna have to bust out his checkbook if he's gonna copy the fatkid again :eek:

hey dude his and chris's look nothing alike unless your on crack or some thing don't be jelouis what you can't have:flipoff2: :flipoff2: :flipoff2: :p :flipoff2:

nuttzack

10-02-2002, 08:45 PM

Well it's lookin like Azrockrawler is gonna have to bust out his checkbook if he's gonna copy the fatkid again

That has to be one of the most retarded frikin things I've heard on here in a looooong time:confused:

fatkid

10-02-2002, 08:46 PM

Originally posted by nozuk

hey dude his and chris's look nothing alike unless your on crack or some thing don't be jelouis what you can't have:flipoff2: :flipoff2: :flipoff2: :p :flipoff2:

You should see what Mustard does have, when the new Tubed propane injected Cruza hits the board you'll be Jelouis...:flipoff2: :flipoff2:

nuttzack

10-02-2002, 08:47 PM

looks awesome though:flipoff2:

Pappa Smurf

10-02-2002, 08:55 PM

ooooooooooooooooooooh! propane i can get a vehicle paid for if i put that on. it where you gonna get propane in the middle of the rubicon:p

Azrckcrawler

10-02-2002, 08:57 PM

Originally posted by Mustard Dog
Well it's lookin like Azrockrawler is gonna have to bust out his checkbook if he's gonna copy the fatkid again :eek:

Yeah, I better get my front end tubed :confused: Looks nice FK, those tires make your rims look like matchbox rims :D

fatkid

10-02-2002, 09:05 PM

Ya know I'm not sure where you can get propane on the Con, I think I'll ask Lance where him and Roggy get there buggies filled up at... Or maybe Jimmy I think he's running Propane...

:confused:

RE:Todd

10-02-2002, 09:05 PM

Originally posted by Bill4rest

do you have a Tin Bender named Pat? in the NAVY and has a red CJ5 or at least used to have. Flat Girl, blue early model Flat fender with Toy axles, just made CPO, would be the one.

fatkid

10-02-2002, 09:11 PM

That's Pat, however he sold that red CJ. He has a new CJ5 that's silver and Toy'd out! Not to mention Pats rig is at my shop with the body off, and it's going to get some extra special attention from the Tin:skull:Benders

Pappa Smurf

10-02-2002, 09:42 PM

we seem to be able to get to the second page very quikly:p :rolleyes: :p :p :p :p :p :p :p

Bill4rest

10-02-2002, 09:50 PM

Originally posted by RE:Todd
Flat Girl, blue early model Flat fender with Toy axles, just made CPO, would be the one.

He's a chief now huh? I guess he can't be my friend anymore:flipoff2:

Bill a member good standings in the Kaki haters club.:p J/K

tdavis

10-02-2002, 11:17 PM

Originally posted by fatkid
Pic of the new Toy tranny with Ultimate T- Case set up, not to mention the SOS Ringer adapter.
:)

hey, that looks famaliar!

Now, all I need to find is that pesky pilot bearing, and I'm set.

btw, what spline? 21 or 23?

MuddMachine

10-03-2002, 05:38 AM

Hey Fatkid, why not another set of boggers ?

scwafish

10-03-2002, 05:51 AM

Now, all I need to find is that pesky pilot bearing, and I'm set.

Have you tried looking at a bearing store:idea: :flipoff2: ..I have the PN if you need it.

We went back to the con last weekend and the RingR/toy stuff works AWESOME. Too bad a few people on this BBS chased Kerry off. He's a cool guy, and his adapters are 2nd to no one...better than damn near anything out there.

Mustard Dog

10-03-2002, 06:59 AM

Originally posted by Titanium
Hey Fatkid, why not another set of boggers ?

The Boggers don't work too good on the trails down here unless you groove the hell out of them;)

fatkid

10-03-2002, 07:32 AM

The Boggs just don't work as well as a Swamper. For now I going to give these a shot.

tdavis

10-03-2002, 07:37 AM

Originally posted by scwafish

Have you tried looking at a bearing store:idea: :flipoff2: ..I have the PN if you need it.

yes, I am calling a bearing store today. I only started looking yesterday.

fatkid

10-03-2002, 08:13 AM

I Need those bearing as well to complete the project too. I also need some time.:D

Mustard Dog

10-03-2002, 10:35 AM

Originally posted by nozuk
ooooooooooooooooooooh! propane i can get a vehicle paid for if i put that on. it where you gonna get propane in the middle of the rubicon:p

You mean to tell me they quit selling propane at that Chevron station just outside the Box:confused:

:D :flipoff2:

DSI

10-03-2002, 10:39 AM

Originally posted by fatkid
I Need those bearing as well to complete the project too. I also need some time.:D

applied technologies right down the street from me had it ON THE SHELF for 13 bucks :)

BTW what clutch plate did you decide to go with?? i ordered teh 71ish celica one since i didn't have to grind any on it, i think that was like 18 bucks?

also, have you done the throw out bearing yet Phatty?? have fun and i suggest a respirator the material that's made of is nasty to breathe :D

tdavis

10-03-2002, 10:47 AM

found a local place that has the bearing, so I'm set on that one. and it's not Applied Technologies. :)

The 70/71 celica clutch plate is on order, (yea, nobody around here stocks it...) got everything else.

Looks like I might get done before Fatty does.

DSI

10-03-2002, 10:51 AM

Originally posted by tdavis
found a local place that has the bearing, so I'm set on that one. and it's not Applied Technologies. :)

The 70/71 celica clutch plate is on order, (yea, nobody around here stocks it...) got everything else.

Looks like I might get done before Fatty does.

mine's been assembled and installed for about 3 weeks now, i just have to finish building the rig around it now :D

rotozuk

10-03-2002, 10:58 AM

Originally posted by DSI

BTW what clutch plate did you decide to go with?? i ordered teh 71ish celica one since i didn't have to grind any on it, i think that was like 18 bucks?

You guys now the diameter of that Celica disk? I'm going to need a disk that is about a 1/2" smaller the the Toyota truck disk for my Mitsubishi engine swap into Toyota driveline.

Thanks,

-Wayne

tdavis

10-03-2002, 11:15 AM

Originally posted by rotozuk

You guys now the diameter of that Celica disk? I'm going to need a disk that is about a 1/2" smaller the the Toyota truck disk for my Mitsubishi engine swap into Toyota driveline.

Thanks,

-Wayne

1970/1971 (to 8/71) Toyota Celica , 7-7/8" diameter, 1-1/8, 21T

tdavis

10-03-2002, 11:16 AM

Originally posted by DSI

mine's been assembled and installed for about 3 weeks now, i just have to finish building the rig around it now :D

So I may get done before you too. :D :D

DSI

10-03-2002, 11:21 AM

Originally posted by tdavis

So I may get done before you too. :D :D

that's a guarantee... i'm going to pull teh D44's out and swap to D60's, so it'll be about 2 weeks before i get axles back under it, and i want to lower it a bit more... and there's a few other thing's on tehre that bother me... so i think i'll redo them too... so since calroc's is over, i got till newyrs :D

poppycock

10-03-2002, 12:10 PM

hey scwa what are the part #s for the pilot and throw out bearing? i'm finally gonna stick the clutch in :D

tdavis

10-03-2002, 01:36 PM

The pilot bearing is SKG/FAG 16101.

The throwout is any 1.6/1.3 throwout bearing (they appear to be identical to me)

DSI

10-03-2002, 01:49 PM

Originally posted by tdavis
The throwout is any 1.6/1.3 throwout bearing (they appear to be identical to me)

i am not sure if they are the same or not, but you do have a little bit of boring to do... the center of the bearing is made of a nylon/poly type stuff and took about 10 min to make fit properly with a small air wheel...

Dychen

10-03-2002, 02:29 PM

snowline gas station in pollick pines (spelling) sells it, and last time i heard it was the cheapest propane in the area (under a buck a gallon). I think you might be able to get some at robs to. Not to mention, if you got a propane stove or if anyone else does, you can get yourself more propane :D

bobaki

10-03-2002, 06:48 PM

poppy I have an extra brg -$12 come by..................:D

scwafish

10-03-2002, 07:54 PM

i am not sure if they are the same or not

They're not...some don't have the plastic inner race. I hogged mine out with a small sanding drum almost the same size as the bearing ID on the drill press. It took 5 minutes to get a cozy slip fit.

tdavis

10-03-2002, 08:04 PM

well, the pipsqueak bearing was the second easiest part to get. :) (the throwout bearing was on the shelf at the local Kragens). Got the rest on order - pressure plate (aka, clutch cover) and toy celica disk.

The throwout bearing I was given has the same part # as the 1.3 bearing (according to http://www.partsamerica.com) and it has no plastic sleeve in it. Come to think about, I'm comparing it to a 1991 samurai, which they might have upgraded it..

fatkid

10-03-2002, 10:59 PM

All you need is a cross member...

slider

10-04-2002, 06:46 AM

so fatty...with the length of your driveline...what do you think?...

a 4" rear drive shaft?...hahaha

fatkid

10-04-2002, 06:58 AM

It should have been short, however we made a few adjustments on the wheelbase...

say about 12.5"

The rear Drive shaft measures around 30"

MuddMachine

10-04-2002, 07:07 AM

Fatkid, u plan on competing with those 39.5's ?

fatkid

10-04-2002, 07:13 AM

Not sure, I setting up a set of Comp tires on my beadlocks. Maybe 37" MTR's

tdavis

10-04-2002, 09:55 AM

Originally posted by fatkid
All you need is a cross member...

Yea, yea, yea.. and tunnel cover.

scwafish

10-04-2002, 01:08 PM

and it has no plastic sleeve in it

The plastic lined and all metal throw-outs are the same pn...just depends on the bearing mfg.

bobaki

10-04-2002, 02:39 PM

I was told Napa #N4092 NTN will get you the right one...........:D

tdavis

10-04-2002, 04:19 PM

Originally posted by fatkid
All you need is a cross member...

Think this will work? (might need some trimming..)

http://www.frontrangeoffroadfab.com/images/xmemberskid019_large.jpg

scwafish

10-04-2002, 06:08 PM

Those are cool...I thought about using one.

bobaki

10-04-2002, 07:12 PM

try this http://www.tennessee4x4.com/toyota/custom_fabricated_parts.htm
they have the basic plate.........................:D

tdavis

10-04-2002, 07:51 PM

Originally posted by bobaki
try this http://www.tennessee4x4.com/toyota/custom_fabricated_parts.htm
they have the basic plate.........................:D

Yea, I sent email to drm.. No reply.

I'm getting the FROR one cheap. :D

BTW, I just destoried a metal throwout bearing, so I'm off to NAPA tomorrow to look for the plastic one.

mikrosilakhan

10-04-2002, 08:15 PM

Great pics.... I already feel sad though wondering how long before the first ""HEY NICE JEEP"" reaches your ears

SamuraiChris

10-05-2002, 08:09 AM

http://www.frontrangeoffroadfab.com/images/xmemberskid019_large.jpg
That thing is pretty sweet, should be real easy to make one of those, how thick should they be, 1/4"?

DSI

10-05-2002, 09:33 AM

Originally posted by fatkid
Not sure, I setting up a set of Comp tires on my beadlocks. Maybe 37" MTR's

that does officially confirm your :rainbow:ness :flipoff2:

tdavis

10-05-2002, 11:52 AM

Originally posted by bobaki
I was told Napa #N4092 NTN will get you the right one...........:D

Ok, I just stopped by the local NAPA, and they don't have it in stock - and list two different manufacturers for it.

Who made the one your using?

I just measured the toy tranny, and it's 35mm in size, and the chicago rawhide (pn N4092) is 33mm in size.

So, HELP!

bobaki

10-05-2002, 03:27 PM

mine says NTN-VALEO on the face...........:D

fatkid

10-06-2002, 09:40 AM

Originally posted by tdavis

Think this will work? (might need some trimming..)

http://www.frontrangeoffroadfab.com/images/xmemberskid019_large.jpg

Whats this one going for?

poppycock

10-06-2002, 12:59 PM

$300 for the crossmember and skid.

tdavis

10-06-2002, 02:51 PM

Originally posted by poppycock
$300 for the crossmember and skid.

hehehe.. $175, drive 120 miles. (Healdsburg) :D

fatkid

10-07-2002, 07:02 AM

Seems a bit much to still have to tweak on to me, Let me see what I can come up with.

tdavis

10-07-2002, 07:39 AM

Yea, it is. I've got it, and it does have to be cut down to fit - it's waaaay too wide. If you do come up with something, I can always sell it and get my money back.

But I'm kinda in a hurry now. :D

I have to figure out what to do on the passenger side inner frame rail. It's covered with fuel and brake lines, so I have to either re-route or come up with a way to mount over/under them.

nomorejeep

10-13-2002, 09:36 PM

hey fk do you have any more pics of ur junk ?

rotozuk

10-13-2002, 10:29 PM

Originally posted by poppycock
$300 for the crossmember and skid.

Damn.. when i was going to be hanging my toyota's divorced with the OTT, I drew up some plates like that for the front and the rear, and had my laser cutter pull one of each for $40 (the minimum order). You could just cut some up with a torch for even less.

The Skid plate is a different story.. I wasn't going to run one. :eek: At most I was going to run a flat plate from frame rail to frame rail since I had the whole thing mounted up that high. :)

Now that I'm taking a new direction with the project, I will see. I do not think the t-cases will be mounted as high anymore. Still not sure the need for the skid plate under a Samurai is needed if you have rubber mounts that have some give to them. I used to roll the GRS2 around on the ocasional rock that got up there, and had no problems at all. but this new vehicle will be seeing more abuse more often... your milage may very.

-Wayne