|
schwarzweld 10-07-2002, 06:07 PM If anyone needs info or pics on anything pertaining to Mogs,E-mail me with your sh?t, I've got access to approx. 30 unimogs about 3 minutes away from my shop. Plenty of pics and a working knowledge of these beast's might help someone in a jam. schwarzweld@aol.com Later :smokin: Station 10-07-2002, 08:34 PM I need some 9" wheels. Do you have some that you are willing to sell? My axles(U-1300) are supposed to be reasy to pick up by next weeend, and I still don't have any wheels. I am looking for wheels without the step. They have to be in good condition, as I plan to use these wheels for a while. If you really do have good knowledge of Mogs, then I say you will be very usefull around here. We are short on Mog experts that know about more than the axles. We have a few overall Mog experts, but they are not around too often. Thanks, Sean Station 10-07-2002, 08:38 PM Oh, and that call out fow wheels goes out to anybody that can sell some to me. I am looking to buy 5 wheels. Hoping to pay around $40 per wheel. Thanks, Sean unissamog 10-08-2002, 11:50 AM where is there a stash of 30 mogs? coachgeo 10-09-2002, 08:19 AM I'll back him up! Yeah he is around alot of mogs and yeah he is an up and up kinda guy. Welcome on board Steve. How is things going with the Tranny Cooler/spray bar Ideas? jeeper350 10-10-2002, 10:23 AM How much for a pair of used mog portal axles? smoothcharlene 10-10-2002, 10:53 AM Originally posted by coachgeo I'll back him up! Yeah he is around alot of mogs and yeah he is an up and up kinda guy. Welcome on board Steve. How is things going with the Tranny Cooler/spray bar Ideas? You're probably going to end up spending close to $2,000 for the pair. roughly 1,200 for a front and 800 for a rear. At least that's what i've seen them for. smoothcharlene 10-10-2002, 10:54 AM Originally posted by Station I need some 9" wheels. Do you have some that you are willing to sell? My axles(U-1300) are supposed to be reasy to pick up by next weeend, and I still don't have any wheels. I am looking for wheels without the step. They have to be in good condition, as I plan to use these wheels for a while. Sean I need some wheels too...anyone have some for sale for cheap let me know jeeper350 10-10-2002, 06:08 PM Yea thats about what i have been looking at, is that with the torque tubes converted? or will I have to do that? How hard is the conversion? TNToy 10-13-2002, 10:08 PM If I'm correct, you don't need to do a torque tube conversion unless you run mog 406's. The more typical 404s are different. Now someone tell me I'm wrong. I probably am. coachgeo 10-14-2002, 06:56 AM Originally posted by TNToy If I'm correct, you don't need to do a torque tube conversion unless you run mog 406's. The more typical 404s are different. Now someone tell me I'm wrong. I probably am. 404's use torque tubes too. So I guess that means ur wrong unissamog 10-16-2002, 06:49 AM Originally posted by jeeper350 Yea thats about what i have been looking at, is that with the torque tubes converted? or will I have to do that? How hard is the conversion? To put 404 axles under any non-mog you will have to use an adaptor to remove the torque tubes and add a yolk. this is what Extact, and others do. Wolfgang 10-16-2002, 08:44 AM Unissamog Not always, we are starting to build a Transfer Case to use the torque tubes with any kind of transmission and motor in any kind of frame also tube frames. You only have to build a solid mount on the frame for the TC. Right now we have running one truck since 1 year without problems (yellow Toyota) . www.killeraxles.com | |