All right, here they are.
http://artecindustries.3dcartstores.com/assets/images/highsteer/d60-knuckle-assembly-features3.jpg (http://artecindustries.3dcartstores.com/High-Steer-Arms_c_125.html)http://artecindustries.3dcartstores.com/assets/images/KOH11/KOH11-d60display.jpg

http://artecindustries.3dcartstores.com/assets/images/highsteer/d60-arms2-5hole_small.jpghttp://artecindustries.3dcartstores.com/assets/images/highsteer/d60-arm-bottom_small.jpghttp://artecindustries.3dcartstores.com/assets/images/highsteer/d60-knuckle-assembly2_small.jpghttp://artecindustries.3dcartstores.com/assets/images/highsteer/d60-arms-engrave_small.jpghttp://artecindustries.3dcartstores.com/assets/images/highsteer/d60-engrave-cu_small.jpg

--------NOW AVAILABLE FOR PREORDER--------
Shipments begin Mid December

THE ONLY HIGH STEER ARM YOU'LL EVER NEED!Whether you are just starting out with crossover steering or going full hydro, these arms are meant to handle it all and GIVE YOU OPTIONS AS WELL! Paired with our optional Knuckle Bolt Kit, the exclusive design of these arms not only allow you to set how you attach your steering links but where as well and increase overall knuckle and steering strength at the same time. Check out the diagrams below of just some of the steering linkage mounting options.

Rather than use the factory kingpin springs, the knuckle is held together with a springless design that uses a set screw to adjust the torque required to hold together. This eliminates some of the slop that is commonly found in axles that receive moderate offroad abuse. The hardware for a springless conversion is included and consists of a 3/4" set screw, jam nut, grease zerk, .250" thick load washer, and upper kingpin bushing for each arm.

Studs and nuts are not included and are available for purchase separately here. Arms are machined blank to allow custom tie rod and draglink locations. Optional drilling for 3/4" bolt or reaming for GM 3/4 ton TRE's (commonly referred to as 1-tons) available.

The Knuckle Bolt Kit is available separately and comes with a 3/4" grade 8 bolt, a 3/4" all- steel mechanical locking nut, and a 1.25" outer diameter, .250" wall sleeve. The sleeve is machined to allow direct contact and proper mislaignment for a 3/4" rod end (heim) ball. The Knuckle Bolt hole is NOT machined into the high steer arm, and the customer will be required to align and drill their own hole in both their knuckle and high steer arm with a 3/4" drill bit.

NOTE: Wheels with extremely large backspacing should not be used in conjunction with this high steer arm. These arms have been confirmed to fit 17", 4.75" backspaced wheels. Will NOT work with factory backspaced H1 wheels. The bulge on the side of the arm measures 1.25" from the spindle mounting surface. Please confirm you have adequate space between arms and wheels/tires before purchasing.

FEATURES:
•Designed to incorporate Knuckle Bolt Kit increasing strength
•Optional Knuckle Bolt Kit puts full hydro in DOUBLE SHEER
•Crossover Steering or Full Hydraulic Steering compatible
•Machined blank to allow customizable tie rod location
•Optional drilling for GM TRE's or 3/4" bolts available*
•Proper 9 degree angle to compensate for knuckle kingpin inclination
•Springless design eliminates slop caused by preloaded spring
•Springless hardware included
•Grease zerk fitting for kingpin lubrication
•5 tapered stud holes for use with OEM or Reid Racing Knuckles
•Optional 6 holes w/ machined Keyway for Solid Axle Knuckles*
•CNC Machined from 1.25" thick 1018 Cold Roll Steel
•Precision machined Artec Industries Logo
•Aerospace-quality spec machined
•Custom Finishes available upon request**


Some Possible Configurations
http://artecindustries.3dcartstores.com/assets/images/highsteer/high-steer-configs2.jpg


*Extra machining is special order and may increase leadtime. Additional costs may apply.
**If you have custom requests, please contact us directly and we can provide you with a quote.

PRODUCT LINK (http://artecindustries.3dcartstores.com/High-Steer-Arms_c_125.html)

And don't forget to use the 10% off coupon when checking out. That'll save you a bunch of $$. pirate4x4

whats the purpose of the fold down the top of the arm?

3 reasons---1.weight savings, 2. Allows use of standard length set screw for the springless conversion, 3. If customer wanted to add a 1 inch spacer underneath, they can still use the same studs instead of buying longer studs.

In order to allow both the 9 degree angle and the ability to line up with the stock knuckle and keep the material thick enough to not loose any strength, 1.25" material needed to be used from the beginning. Rather than keep that big block over the studs where its not needed, ordering a longer set screw, and prevent possible use of a 1 inch spacer if a customer desired, it was milled down. Solidworks simulations showed no effect on strength.

Here is a quote from Azrckcrawler of Built to Grind fame on what makes the Artec arms so special.
A couple of us have been running hacked together setups utilizing 1018 steering arms and tying the arm into the stock tie rod hole. The concept in my mind is proven. In 6 years I have not had any broken studs or knuckle failures but have seen plenty of failures on the trail with the typical high steer arm just bolted to the top of the knuckle. Our buddy Chad was busting studs on his rear steer axle so often he carried an easy out kit and a cordless drill onboard for trailside stud extraction. Once he tied the steering arm into the stock TRE hole his problems went away.

Not only does this system allow double sheer on the heim joint, it completely reinforces the whole knuckle and helps prevent stud sheering. Mounting like this distributes more force to the knuckle itself and less force on the studs. Not only that, it allows total customization of how high you mount your ram. Most high steer arms are too high when compared to the location you want to mount your ram but because thats where the high steer arm is, you are forced to put the ram that high. Not so with the Artec Ultimate High steer arms. Simply cut the sleeve between the knuckle and high steer arm to your desired length to get a perfect height. If you look around at many of the KOH buggy builds happening right now including the 4405 Phoenix Land use buggy, they are attaching their steering in this method but heavily modifying normal arms to accomplish this. Here's the graphic again that shows just of few of the mounting options available with the Ultimate Dana 60 High Steer arms from Artec Industries. I basically just described the first two graphics on the left. Of course this only scratches the surface of options if you consider all the heights you can mount a heim on the Knuckle Bolt kit and even mounting heims under the high steer arms for crossover and so on.

http://artecindustries.3dcartstores.com/assets/images/highsteer/high-steer-configs2.jpg

man these are hot!!!

They sure are....but let me give you something really cool.....

http://artecindustries.3dcartstores.com/assets/images/promotions/Artec-Freeze-Sale.jpg

To celebrate record low temps here in Arizona (and the end of everyone's Turkey comas), we've decided to have an ARTEC FREEZE party and everyone is invited. (Just don't try to order online while wearing mittens, it doesn't work very well;))

That's right, we are running 20% off any parts we make for TWO WEEKS ONLY. This includes the NEW ULTIMATE Dana 60 High Steer Arms (http://artecindustries.3dcartstores.com/High-Steer-Arms_c_125.html), the NEW QUART CRATES (http://artecindustries.3dcartstores.com/Quart-Crates_c_127.html), the industries largest selection of Battery Mounts (http://artecindustries.3dcartstores.com/Battery-Mounts_c_99.html), tabs, beadlocks, etc.

The discount will show in the shopping cart when you add an item. Cannot be combined with any other offer.

GET THESE COOL DEALS NOW BEFORE IT WARMS BACK UP AGAIN!!! GREAT CHRISTMAS PRESENT UNDER $20!!! (http://artecindustries.3dcartstores.com/Quart-Crate--6-quart-holder_p_162.html)
http://www.artecindustries.com/

The pics only show a flat surface, but are the tops of the bolt holes tapered to accept the nuts?


Quote for a pair of arms (setup for 6 holes/Solid keyway), knuckle bolt kits, & 12 studs/nuts shipped to 02035 please.

That's a great question. YES. They will have countersunk holes to accept the tapered nuts. The images above are from our prototypes in which our prototype tester wasn't using tapered nuts.

PM sent. Thanks for the chance to quote.

And don't forget to use the 10% off coupon when checking out. That'll save you a bunch of $$. pirate4x4

This code isnt accepted by the site it keeps coming up with this..

Home > Invalid Coupon
Invalid Coupon
Your coupon is not valid!
Pirate Coupon

If you check the post above it says cannot be combined with any other offer. Sorry. But if you type in the word pirate in the comments field when checking out, I'll throw in some extra goodies.:D

I thought the 20% was only on Artec products.

That's right. Hardware and other items I don't make are regular price (see graphic above). You are saving almost $80 on your high steer arm order.

Wow, thanks for all the orders. Apparently alot of you having been waiting for a set of high steer arms like these at just this price.

Get them NOW and Save BIG!

Lookin' for 2 arms with stud kits (8 studs / nuts total) and D60 knuckle bolt kit shipped to 71913. Thanks!

PM sent. Thanks.

Everyone, don't forget we also sell 3/4" and 7/8"x3/4" heims to mount to the Knuckle Bolt Kit at great prices as well.

Having problems sheering studs? These arms are your fix! Reinforce the entire knuckle and strengthen your steering.

I wish you had started this thread 2 weeks earlier :(
I thought the only option I had for the SOLID knuckles was the SOLID arms

... oh well

Surely they at least have a 30 day return policy. I'm not saying their arms are bad but no other arms have the designs and features of these so...you should get what you need right, especially if you thought there was only one manufacturer making them.

A sample of a installed picture. I'll post up more on Monday. Hopefully this gives you an idea of how this whole system really adds strength to the knuckle and flexibility in how you mount your steering.

http://artecindustries.3dcartstores.com/assets/images/highsteer/ultimated60installed.jpg

I didn't see anywhere that mentioned what the distance or range of distance was from the center cap(setscrew) to the hole for the rod end. For example: some arms are 6" or 7" or 8" or whatever depending on your hydro setup.

Surely they at least have a 30 day return policy. I'm not saying their arms are bad but no other arms have the designs and features of these so...you should get what you need right, especially if you thought there was only one manufacturer making them.

I've already drilled them:(

EDIT;when i upgrade to a springless I want these ... no brainer ... I might be upgrading sooner than I thought

Holy schnikes!!! A bunch of orders over the weekend and this morning for these arms. Thanks pirates.

ONLY TWO DAYS LEFT FOR THE 20% OFF SALE!!!!

These are perfect for those winter builds. Don't go out this spring worrying about your knuckles and steering. Get the ULTIMATE High Steer Arms!

Can I get a quote on 2 sets of these high steer arms shipped to 95315

What options do you want? There are lots of options (5-hole, 6-hole with keyway, blank or holes drilled) we offer and accessories too (4 stud/nut kit, 5 stud/nut kit, Knuckle bolt kits) so I want to make sure the quote is accurate.

Our website can do a shipping quote easily and show the sale discount once you add items to the shopping cart.

http://artecindustries.3dcartstores.com/High-Steer-Arms_c_125.html

ONLY HALF A DAY LEFT!!! 20% off ends tonight at midnight.

Last call before I head out of the office today. Of course you can still order it online until midnight.

A few more sets of these have sold in the last couple of hours. I'm gonna have to get on the phone tomorrow morning and order some more material at this rate. Thanks for the orders.

Don't forget to add a Knuckle bolt kit for each side to really take advantage of the full features of these arms.

got my order in last night before the sale went off!!
any idea on the lead time right now (just curious??)

any idea on the lead time right now (just curious??)

x2

We're running a little behind right now. My machinists are starting to tear down the fixtures from the previous jobs and will be setting up the fixtures for these next. We should hit the ground running on Monday to start machining full production. We are hoping to start shipping at the end of next week. Won't make it to anybody by Christmas though, sorry.

Here are some photos from the install on AZrckcrawler's build.

http://artecindustries.3dcartstores.com/assets/images/highsteer/d60hs4.jpghttp://artecindustries.3dcartstores.com/assets/images/highsteer/d60hs5.jpg
http://artecindustries.3dcartstores.com/assets/images/highsteer/d60hs6.jpghttp://artecindustries.3dcartstores.com/assets/images/highsteer/d60hs1.jpg
https://artecindustries.3dcartstores.com/assets/images/highsteer/d60hs2.jpghttps://artecindustries.3dcartstores.com/assets/images/highsteer/d60hs3.jpg
http://artecindustries.3dcartstores.com/assets/images/highsteer/d60hs7.jpghttp://artecindustries.3dcartstores.com/assets/images/highsteer/d60hs8.jpg

If you missed the sale, remember we still offer the 10% OFF PIRATE COUPON. Just type in pirate4x4 in the coupon field.

what back spacing wheel will they clear?

NOTE: Wheels with extremely large backspacing should not be used in conjunction with this high steer arm. These arms have been confirmed to fit 17", 4.75" backspaced wheels. Will NOT work with factory backspaced H1 wheels. The bulge on the side of the arm measures 1.25" from the spindle mounting surface. Please confirm you have adequate space between arms and wheels/tires before purchasing.

quoted from above

Here are some photos of production of the Ultimate High Steer Arms. Its taking a little longer than expected just because everything is so busy right now but I'm hoping shipments will begin at the end of this week.

http://artecindustries.3dcartstores.com/assets/images/highsteer/hsproduction.jpg
http://artecindustries.3dcartstores.com/assets/images/highsteer/hsproduction2.jpg

you gonna be shipping the orders from the "Freeze" sale this coming week???

you gonna be shipping the orders from the "Freeze" sale this coming week???

Speaking of FREEZE, a huge cold weather system moved through the western US and delayed our production of these somewhat. We're working on wrapping these up in the next two or three days and shipping them out. We've sent out notifications to all those waiting on these high steer arms. Everyone who ordered these should get a tracking number once shipped, provided the email they provided was correct.

Here are some photos of the ULTIMATE High Steer Arms in action. http://www.pirate4x4.com/forum/showthread.php?t=901011&page=7

http://artecindustries.3dcartstores.com/assets/images/customers/CV/CVbuggyHS1.jpghttp://artecindustries.3dcartstores.com/assets/images/customers/CV/CVbuggyHS5.jpg
http://artecindustries.3dcartstores.com/assets/images/customers/CV/CVbuggyHS7.jpghttp://artecindustries.3dcartstores.com/assets/images/customers/CV/CVbuggyHS8.jpg
http://artecindustries.3dcartstores.com/assets/images/customers/CV/CVbuggyHS3.jpg

We are beginning the last operation of these today, engraving. Once they are done, they'll get boxed up and shipped off (likely tomorrow). Thanks to all those who have been waiting so patiently.

Shipped out a large number of high steer arms on Friday. All those with arms that did not have any of the optional holes or machining should have received tracking numbers via email. If your arms had crossover steering holes drilled in them, it'll probably be a few more days as we wait for a machine to free up. Six hole arms with keyway are going to take some more time, unfortunately. If you have concerns about your order, please contact us.

EDIT: My machinist just opened up a machine and is drilling the optional holes today. As soon as they are done, they will ship out. Some of you may receive tracking numbers tonight.

just received my order today.

they look great and I look forward to the install.

Machined a big batch right before we went out to KOH and nearly sold through the whole thing.:eek:
Guess I need to order more steel to make some more. i still have a couple sets left. First come first serve.
I think the concept was really easy to understand from the way we had it displayed.

http://artecindustries.3dcartstores.com/assets/images/KOH11/KOH11-d60display.jpg

Seems like you sold a ton at 20% off and I miss it. If you guys have another sale like that I think I'd buy a set. I really like the option of bracing to the stock tre hole. I hope you consider doing it again!

You can save 10% right now with the pirate4x4 coupon.

On our way back to Hammertown after watching Backdoor, I spotted AZrckcrawler's rig and took some photos of it. He had been beating on it all week and even told me that the steering arms were the only bolts that hadn't loosened all week. When the guys from Built to Grind say they have been beating on the rigs all week, you know that they are giving those parts the best real world (ab)use you could possibly ask for. Watch the video to see Azrckcrawler (ab)using his stuff and making a sweet save.

http://artecindustries.3dcartstores.com/assets/images/KOH11/KOH11-Chris1.jpg

YouTube - 2011 King of the hammers redneck faceplant backflip save (http://www.youtube.com/watch?v=f0oCjtKDFxE)

How about another 20% OFF special so I can buy 2 kits?????

These things are really popular right now. Thanks for all the orders.

Its Saturday afternoon or I'd call but looking for a little insight on what is going wrong here. Anybody drilled their arms yet?

I dropped off the arms and my 79 Ford knuckles to be drilled out and something is not lining up right.

They arms are bolted to the knuckles and the machinist is using the stock hole as his reference in drilling the Artec arm.

Well as you can see from the pictures we are going to have a problem, and thats with a 5/8 drill. A 3/4 hole is gonna eat right through the side of the arm.

The stock knuckle does not look bent. And it would have to be 1/2" or so off. And I dont have a comparison of the other arm/knuckle on the drill as he wanted to show me before he took it off. Being a weekend he was reluctant to set up the other side today for me.

I would have to guess that the Ford knuckles are slightly different than the GM...

So what's the deal with these fitting Ford knuckles?

DO they fit??

We're looking into it. We'll have more information soon.

Nate,

I dont have any better pictures for you, the machinist already had them off the table when I got there today. sorry.

So what's the deal with these fitting Ford knuckles?

DO they fit??


Hmmm glad I read this thread, was about to pull the trigger on a set...

What's the word on Ford knuckles?

I can't go true hi-steer on mine due to frame clearances and I can't just set on top of the stock steering arm due to interference with the dif cover so these look to be perfect way to get my steering somewhere in between...

Looking forward to an answer...

Sean, again sorry for the inconvienences. Can you still check the other side knuckle and high steer arm to see if the problem just lies with that knuckle that was put on the machine? I don't need it to be setup in the vice and machine or anything, just put the arm on the knuckle and see if it looks like the hole placement will be generally in the same place.

We're looking to source that year axle here locally to see if the problem is specific to that year axle. Original calculations placed the hole more inward towards the center of the high steer arm. Whatever we find, we'll make sure to take care of those who are running into issues even if it means machining a custom arm to match their needs. We will work our hardest to resolve this issue quickly so that Ford owners don't have to hold off ordering.

Prototype testing was done on Solid aftermarket knuckles and we have confirmed that they work on all OEM Chevy and OEM Dodge knuckles, as well as aftermarket Reid Racing (both Ford and Chevy versions), and Solid Knuckles. I am also looking into custom machining the keyway for Crane knuckles as well.

Nate, I took a look today and it looks the same on both sides to me. That is, the nothing looks bent or out of place on either knuckle.

It almost appears that if the 'nub' portion was extended rearward it might work. But without some more measuring you might have an issue with the sidewall thickness after the hole is opened up to 3/4".

Heres two pictures I took today. They arent perfect as the perspective is off a little but you get the idea. Even the picture I took at the machinists looked like the drill was a little off but its really my camera angles.

Sean, again sorry for the inconvienences. Can you still check the other side knuckle and high steer arm to see if the problem just lies with that knuckle that was put on the machine? I don't need it to be setup in the vice and machine or anything, just put the arm on the knuckle and see if it looks like the hole placement will be generally in the same place.

We're looking to source that year axle here locally to see if the problem is specific to that year axle. Original calculations placed the hole more inward towards the center of the high steer arm. Whatever we find, we'll make sure to take care of those who are running into issues even if it means machining a custom arm to match their needs. We will work our hardest to resolve this issue quickly so that Ford owners don't have to hold off ordering.

Prototype testing was done on Solid aftermarket knuckles and we have confirmed that they work on all OEM Chevy and OEM Dodge knuckles, as well as aftermarket Reid Racing, and Solid Knuckles. I am also looking into custom machining the keyway for Crane knuckles as well.

Sean, thanks for those pictures. That really helps.

I'm going to hit some junkyards up tomorrow to see if can get my hands on a 78-79 axle. I'll let you know what I find.

Just want to post up that nate has been pro-active with this issue, reaching out to other folks that purchased the ford knuckle version. He has kept me up to date with the issue and it seems as though they will be rereleasing the ford version soon. I am confident that nate and artie will make this right in a timely fashion and square away customers that were impacted by the error.

Just want to post up that nate has been pro-active with this issue, reaching out to other folks that purchased the ford knuckle version. He has kept me up to date with the issue and it seems as though they will be rereleasing the ford version soon. I am confident that nate and artie will make this right in a timely fashion and square away customers that were impacted by the error.

Thank you for your patience while we get the Ford arms sorted out. We have determined what we need to do and will begin machining Ford arms early next week. We apologize for any inconvenience this may have caused and will make sure to do everything we can to ensure your satisfaction.

BTW, Chevy arms are unaffected by this and are in stock.

Seems like you sold a ton at 20% off and I miss it. If you guys have another sale like that I think I'd buy a set. I really like the option of bracing to the stock tre hole. I hope you consider doing it again!

Usually we offer 20% off for introductory pricing on most of our products, however we don't offer that pricing afterward.

BUT in conjunction with the release of our new COMPLETE FULL HYDRO MOUNTING KIT (http://artecindustries.3dcartstores.com/Dana-60-Chevy-Front-Ram-Mount-and-Truss-KIT_p_183.html) in which we are offering 15% off the ULTIMATE 60 arms in combo, we've decided to offer...

15% OFF ULTIMATE HIGH STEER ARMS AND KNUCKLE BOLT KITS ALONE AS WELL!!!! :smokin:
GET THEM HERE (http://artecindustries.3dcartstores.com/High-Steer-Arms_c_126.html)

Here's our new kit. Build it to your needs whether its just a ram mount and high steer arms or the whole system. Plus you save Mucho $$ when ordered together. COMPLETE FULL HYDRO MOUNTING KIT (http://artecindustries.3dcartstores.com/Dana-60-Chevy-Front-Ram-Mount-and-Truss-KIT_p_183.html)
http://artecindustries.3dcartstores.com/assets/images/truss/dana60/truss-hsa-kit.jpg

15% OFF Ultimate high steer arms and knuckles bolt kits.

GET the BEST for LESS!

LINK (http://artecindustries.3dcartstores.com/High-Steer-Arms_c_126.html)

Looks like the sale was a good idea for those spring builds. Get yours now.

Bunches of these being ordered right now. Thanks for the orders. It just makes sense to connect to the factory tie rod location where its strongest. Plus its a proven design with years of no stud sheer.

FYI, FORD VERSIONS ARE ALMOST DONE MACHINING. They'll be done and ready to ship middle of next week. Thanks for those who've been patient with us. If you want to order the Ford version on the website, please just leave a comment when checking out that you'd like them for Ford.

Bunches of these being ordered right now. Thanks for the orders. It just makes sense to connect to the factory tie rod location where its strongest. Plus its a proven design with years of no stud sheer.

FYI, FORD VERSIONS ARE ALMOST DONE MACHINING. They'll be done and ready to ship middle of next week. Thanks for those who've been patient with us. If you want to order the Ford version on the website, please just leave a comment when checking out that you'd like them for Ford.


Anxious to get my re-machined Ford arms....

The Ford arms are very close to being done.

LAST CALL ON THE 15% OFF SALE. ENDS TONIGHT. LINK (http://artecindustries.3dcartstores.com/High-Steer-Arms_c_125.html)

http://artecindustries.3dcartstores.com/assets/images/highsteer/d60-knuckle-assembly-features3.jpg (http://artecindustries.3dcartstores.com/High-Steer-Arms_c_125.html)

All FORD ARMS are shipping tomorrow. Some of you I'll contact in the morning regarding your orders. Thank you for your patience.

All FORD ARMS are shipping tomorrow. Some of you I'll contact in the morning regarding your orders. Thank you for your patience.

right on

Got the new arms in and will be sending back the old ones once I test fit everything.


Question; can I assume that wheel backspacing tolerances have not changed with the new ford arm. Still able to accept a wheel with less than 4.75" bs????? Please advise ASAP.

In order to accomodate the change in location of the stock TRE on the Ford knuckle, we did have to add .300 to the buldge on the side of the arm. That puts the back spacing to roughly 4.5 instead of 4.75.

good info....glag i went with 4" bs

So are you running an introductory special on the ford arms by themselves, or is that just tied into the special for the chevy ones? Looks like the sale is ending soon....

EDIT: looks like the sale ended?

Pm sent.

For those who'll be at the Silverstate 300, you'll see a bunch of these arms being used by Ultra4 racers. Glad to provide those racers the best and strongest arms on the market.

Of course, you don't have to be a racer to use these. These will help drastically reduce chance of stud sheer on any knuckle, on any vehicle with a front kingpin dana 60.

Looking forward to receiving my arms! Thanks Nate!

figured I should update. I got my new arms in, and since Artec had my knuckles this time I expect everything to go smoothly. I dont have time to put it together for a few weeks though.

Just wanted to thank Artec for taking care of me after the fact. They could have left me(and others hanging) but in the end they made it right and I'm happy.

Its Saturday afternoon or I'd call but looking for a little insight on what is going wrong here. Anybody drilled their arms yet?

I dropped off the arms and my 79 Ford knuckles to be drilled out and something is not lining up right.

They arms are bolted to the knuckles and the machinist is using the stock hole as his reference in drilling the Artec arm.

Well as you can see from the pictures we are going to have a problem, and thats with a 5/8 drill. A 3/4 hole is gonna eat right through the side of the arm.

The stock knuckle does not look bent. And it would have to be 1/2" or so off. And I dont have a comparison of the other arm/knuckle on the drill as he wanted to show me before he took it off. Being a weekend he was reluctant to set up the other side today for me.

figured I should update. I got my new arms in, and since Artec had my knuckles this time I expect everything to go smoothly. I dont have time to put it together for a few weeks though.

Just wanted to thank Artec for taking care of me after the fact. They could have left me(and others hanging) but in the end they made it right and I'm happy.

Thanks for your patience Sean (and others too). Even though you haven't had a chance to bolt everything together, we did. Here's your knuckles and high steer arms all put together.
http://artecindustries.3dcartstores.com/assets/images/highsteer/D60-arm-Ford-knuckle1.jpg (http://artecindustries.3dcartstores.com/High-Steer-Arms_c_125.html)

FYI to all, the Ford arms and the Solid axle arms with keyway were unexpectedly popular this last week and we sold clear through our inventory of both yesterday (and we thought we were making a bunch of extra arms when we started the batch:eek:). We have more material coming next week and should have them ready by the following week.

Chevy/Reid arms are in stock and ready to ship.

I think we sold more arms this week than any other week. Thanks for the orders.

Can you shoot me a price of the arms, all hardware & reid chevy 60 knuckles set up, ready to bolt on.

Thanks, Anthony

PM sent. Thanks for the opportunity to quote.

FYI, we only have a couple of Chevy sets left on the shelf but I picked up a half ton of material today. We should be completely stocked with all versions by mid-next week.

are you going to offer the truss system for fords as well? i'm hopefully going to pick up a ford D60 real soon and was browsing for highsteer truss stuff and am very interested in your product

Yes, we will be offering the Ford truss systems with high steer arms in a kit. I will have it up in the next few days. I'm still working on trusses for the later Ford axles though.

any word on the 'later' Ford axle trusses? 80-90s era kingpin?

any word on the 'later' Ford axle trusses? 80-90s era kingpin?

Design is nearly complete. I will be getting some serious design time tomorrow to wrap it up. Sorry its taking so long. Its a little more complicated than the other trusses and I've had limited design time since we've been slammed shipping out all the other trusses. Hopefully we can cut it tomorrow.

Out of arms for the next couple of days but we have our largest batch yet about 60% done.

ON SALE 15% OFF
ends May 31
http://artecindustries.3dcartstores.com/assets/images/highsteer/d60-arms2-5hole.jpg (http://artecindustries.3dcartstores.com/Ultimate-Dana-60-High-Steer-Arms--Pair_p_154.html#)

The question is not...have you sheared your high steer studs, but when will you shear those studs!

Quit worrying about your steering breaking and get the ULTIMATE high steer arms.

ON SALE 15% OFF
ends May 31
http://artecindustries.3dcartstores.com/assets/images/highsteer/d60-arms2-5hole.jpg (http://artecindustries.3dcartstores.com/Ultimate-Dana-60-High-Steer-Arms--Pair_p_154.html#)

Arms only? What about the bolt kits?

Arms only? What about the bolt kits?

Knuckle bolt kits are on sale as well. Stud kits are not but you can still use your pirate4x4 discount on those.
http://artecindustries.3dcartstores.com/D60-Knuckle-Bolt-Kit_p_156.html

We were hoping to have our batch done a couple days ago, but our lead machinist hurt his leg over the weekend and was out for a couple days. He's back now and makin chips. Should have them ready by late Thursday or early Friday. Sorry for the delays for those waiting.

Wow this was a big batch of high steer arms. They're gonna take one more day to finish. Shipments will begin Monday. Sorry for the wait.

ON SALE 15% OFF
ends May 31
http://artecindustries.3dcartstores.com/assets/images/highsteer/d60-arms2-5hole.jpg (http://artecindustries.3dcartstores.com/Ultimate-Dana-60-High-Steer-Arms--Pair_p_154.html#)

Can I get a quote for 2 arms and 2 bolt kits to 98296? I would like the 3/4 hole that connects the bolt kits to be drilled already.

Thanks,
Ben

Can I get a quote for 2 arms and 2 bolt kits to 98296? I would like the 3/4 hole that connects the bolt kits to be drilled already.

Thanks,
Ben

In order to drill this hole I would need to have the knuckle here to determine where that precise hole location would be.

Theres a really good reason we don't drill the hole location that is directly over the stock location ahead of time. Every knuckle from the factory has a variation of where that location is on the knuckle. We've seen even on the same axle hole locations that vary up to 1/8". While that might not seem much, in steering, things should be very precise to reduce wear and wallowing out.

Additionally, you need to drill out your knuckles too, and depending on if you drill them out at the precise angle to match to our premade hole, it probably won't fit.

Its why every arm needs to be made to fit the knuckle its attaching to. We know it is more work, but its worth it to never have to worry about your high steer arms sheering studs, breaking knuckles, shearing heim bolts, etc. Its a proven system but it just requires a little more work.

For Reid Racing knuckles whose tolerance on the location is extremely precise, we have that location and can provide that hole drilling.

That said, what knuckles do you have?

Just pm'd you before I found this thread again.
I have factory knuckles and I can handle drilling them myself. pm me a quote shipped to 98296.
Thanks,
Ben

Also, I am running KMC beadlocks with 4.75" of backspacing. With that much backspacing will these fit?

Yes they will.

A bunch more arms shipping out today. Thanks for the orders. The sale is still on only for a few more days.

Artec this is Jason aka gotdirt. Thanks for the speedy arms

Artec this is Jason aka gotdirt. Thanks for the speedy arms

You're welcome. Now that we finished a huge batch of these, we have a bunch on the shelf and they will ship the same day you order them if ordered by 1pm PST.

Lots of these ordered over the weekend. Thanks.

REMEMBER, THE SALE ENDS TOMORROW!!!!

Hope you all had a good Memorial Day.

LAST DAY of the SALE!!! Ships same day if before 1pm PST.
http://artecindustries.3dcartstores.com/High-Steer_c_136.html

We've had a lot of people ask lately what to torque everything to when tightening the arms down. There isn't an exact torque spec but I'd say 80-100 ft/lbs on the nuts for the studs. The spring elimination set screw is tightened based on feel. You should be able to move the knuckle back and forth by hand but with some resistance. You don't want it to be sloppy and moving very freely or really hard to move back and forth either.

Wow, that last batch was our largest yet and its already almost gone. We already have another batch machining and this time we decided to double the amount of arms from the last one. Thanks for making these so popular.

Get the strongest arms on the market and stop worrying about your high steer arms and knuckles forever!

Lots in stock, READY TO SHIP!

We've had a lot of people ask lately what to torque everything to when tightening the arms down. There isn't an exact torque spec but I'd say 80-100 ft/lbs on the nuts for the studs. The spring elimination set screw is tightened based on feel. You should be able to move the knuckle back and forth by hand but with some resistance. You don't want it to be sloppy and moving very freely or really hard to move back and forth either.

Some manufacturer's give a lbs resistance recommended. I use a fish weighing hook when I set this kind of thing up (but I'm a redneck so...) Can you tell me how many pound's you'd recommend by this method? Let me know when you get back from Walmart from buying that scale :p

Here is the one scale I use: (http://www.scalesonline.com/490/KILOTECH/KILOTECH-KHS-C3-Series-Industrial-Hanging-Scale.aspx)

Some manufacturer's give a lbs resistance recommended. I use a fish weighing hook when I set this kind of thing up (but I'm a redneck so...) Can you tell me how many pound's you'd recommend by this method? Let me know when you get back from Walmart from buying that scale :p

Here is the one scale I use: (http://www.scalesonline.com/490/KILOTECH/KILOTECH-KHS-C3-Series-Industrial-Hanging-Scale.aspx)

What is wrong with a torque wrench?

Nat

Get the ultimate in strength. Heims in Double sheer and no WORRIES ABOUT STUD SHEER.

We're doing something fun on Facebook that might get YOU closer to owning one of these bad boys. Check it out...http://www.facebook.com/artecindustries

Thanks for all the high steer arm orders. Here's a cool screenshot of our arms, our ram mount and truss and some new brackets we're cooking up.

http://artecindustries.3dcartstores.com/assets/images/LinkBrackets/truss-panhard3.jpg
http://artecindustries.3dcartstores.com/assets/images/LinkBrackets/truss-panhard2.jpghttp://artecindustries.3dcartstores.com/assets/images/LinkBrackets/truss-panhard1.jpg

We got a little low but just finished another big batch. Good timing b/c a bunch of people have ordered these recently. Plenty in stock and ready to ship same or next day.

We've been shipping out bunches of these lately. Thanks for the orders. We know its not the cheapest arms around but they are the BEST. That's why we call the ULTIMATE!

In order to drill this hole I would need to have the knuckle here to determine where that precise hole location would be.

Theres a really good reason we don't drill the hole location that is directly over the stock location ahead of time. Every knuckle from the factory has a variation of where that location is on the knuckle. We've seen even on the same axle hole locations that vary up to 1/8". While that might not seem much, in steering, things should be very precise to reduce wear and wallowing out.

Additionally, you need to drill out your knuckles too, and depending on if you drill them out at the precise angle to match to our premade hole, it probably won't fit.

Its why every arm needs to be made to fit the knuckle its attaching to. We know it is more work, but its worth it to never have to worry about your high steer arms sheering studs, breaking knuckles, shearing heim bolts, etc. Its a proven system but it just requires a little more work.

For Reid Racing knuckles whose tolerance on the location is extremely precise, we have that location and can provide that hole drilling.

That said, what knuckles do you have?




What about solid knuckles? do you know if their holes are accurate enough for you to pre drill the hole? Also are arms made for the solid knuckles left flat around the stud holes so bolts can be used like solids arms do?

Thanks,

Chad

What about solid knuckles? do you know if their holes are accurate enough for you to pre drill the hole? Also are arms made for the solid knuckles left flat around the stud holes so bolts can be used like solids arms do?

Thanks,

Chad

They are probably accurate enough but I don't have their hole location so predrilling them wouldn't be available. If you have access to a drill press, it's not too difficult. Here is a link to an install thread that'll help. http://www.pirate4x4.com/forum/showthread.php?t=987968

They do have a tapered hole currently (the next batch won't) but I have lots of customers that use a washer and gr8 bolts for them just fine.

Dont' forget the pirate4x4 discount. Simply type pirate4x4 in the coupon code section and save 10%. It doesn't apply to ON SALE items but there are only a few of those.

One last set of high steer arms left. Material arrives tomorrow and hopefully we'll be stocked up again by end of next week.

Maybe I should run a deal for those who purchase arms between now and the end of next week and are willing to wait until they're done. Wudduya think?

I'm willing to offer an extra deal for those who are willing to wait until this batch finishes up, but I will only offer it today(8/24) and tomorrow (8/25) because we should be finishing up by Friday or Monday at the very latest. Give me a call to take advantage of this deal. 520-906-9977 Nate

thanks for the help

No problem. Thanks for the order.

I will call in the morning or call me, I want to hear about this deal. In the market and am leaning towards your arms.

PM Sent!!

High Steer arm orders are almost off the charts today. Thanks for the orders. We're going to run another batch directly after the one finishing up tomorrow.

WOW! We tripled our single day record of high steer arms today! Of the batch finishing up tomorrow, I think we only have about 4 sets remaining. I guess we're going to be seeing alot of our arms in build threads soon. :smokin:

WHEW, THINGS ARMS ARE STILL HOT FROM LAST WEEK! Thanks for all the orders. Our current batch has only 2 pairs left and they just finished minutes ago. Good thing we're starting another batch tomorrow.

Our new batch is finishing up in the next two days. This should hold us over for a couple weeks :)

Lots in stock and ready to ship out immediately. Don't forget the pirate4x4 coupon code when checking out.

Ultimate for a reason!

Lots of these arms are going with trusses lately. Must be the 20% off kit pricing we are offering when you buy them together. :D

Dana 60 Highsteer kit
95476

PM sent.

We have lots of these in stock and available for immediate shipment. Why wait for a set of inferior arms from someone else when you can have the best from us right now?

We make these for OEM, Reid and Solid knuckles. The ultimate D60 high steer arms. Don't forget if you are running our product and racing at the Ultra4 Glen Helen Grand Prix we are offering contingency money.

Check this thread out for details.

http://www.pirate4x4.com/forum/showthread.php?t=1014371

We're machining a batch that is twice as big as the last time. Thanks for keeping us busy!

Looks like there will be alot of these at KOH

Best way to run double sheer and eliminates stud sheer.

These have been really popular over the last few weeks. We've again doubled our batch.

These really are the ultimate high steer arms. We also make them for the Solid knuckles.

We just finished our biggest batch of these ever. I'm a little worried our shelves aren't going to hold these things so we put them on all our bottom shelves. Thanks for all the recent orders.

These are a great way to strengthen your steering and these are in stock and ready to ship.

Arms are in stock and ready to ship out.

Any way to get a hold of you guys? I'm missing some parts from my order, been calling and leaving voicemails for the past 2 weeks....

Any way to get a hold of you guys? I'm missing some parts from my order, been calling and leaving voicemails for the past 2 weeks....

I apologize, our voicemail system has been not working correctly and I can't access those messages. Every time our phone carrier says the problem is fixed, its still not working. We are always available via email, PM, or our contact us page. We are usually available on the phone too but sometimes too early in the morning we might not be in the office.

Sending PM now.

Parts shipped out today, thanks for making it right guys:)

Will these clear an H2 wheel?

17x9, with 5.625" back spacing...

Will these clear an H2 wheel?

17x9, with 5.625" back spacing...

We haven't tested H2 wheels but most likely not.
Wheels with extremely large backspacing should not be used in conjunction with this high steer arm. These arms have been confirmed to fit 17", 4.75" backspaced wheels. Will NOT work with factory backspaced H1 wheels. The bulge on the side of the arm measures 1.25" from the spindle mounting surface. Please confirm you have adequate space between arms and wheels/tires before purchasing.

If i use these arms with stock ford dana 60 knuckle in a double shear setup and upgrade to reids later will i be able to use the same arm or are the holes in different locations? just trying to figure out if i should just bite the bullet and upgrade all at once or save the coin and use stock knuckles

thanks for the orders

If i use these arms with stock ford dana 60 knuckle in a double shear setup and upgrade to reids later will i be able to use the same arm or are the holes in different locations? just trying to figure out if i should just bite the bullet and upgrade all at once or save the coin and use stock knuckles

The hole will be in a different location from OEM ford knuckles to Reid and Chevy OEM knuckles.

We haven't tested H2 wheels but most likely not.

[Wheels with extremely large backspacing should not be used in conjunction with this high steer arm. These arms have been confirmed to fit 17", 4.75" backspaced wheels. Will NOT work with factory backspaced H1 wheels. The bulge on the side of the arm measures 1.25" from the spindle mounting surface. Please confirm you have adequate space between arms and wheels/tires before purchasing.]

Are they outboard of the spindle mounting surface, or inboard?

https://artecindustries.3dcartstores.com/assets/images/promotions/Thanksgiving-sale-card.jpg (http://artecindustries.3dcartstores.com/)

Is that 15% off on top of the 10% Pirate4x4 discount?

Is that 15% off on top of the 10% Pirate4x4 discount?

Not valid with any other pricing or promotions. If you have entered the pirate discount it will only show that discount, but you can scroll down in the shopping cart and click the remove button next to the pirate coupon and the sale discount will then show again.

Only a few hours left. 15% off ALL the product we make.

Wrapping up another big batch of these today. 5 bolt versions are in stock now but 6 bolts are backordered probably for another two weeks.

Just finished a large batch of these and they are ready to ship out.

The ultimate in high steer arms, best part is they are in stock and ready to ship.

http://artecindustries.3dcartstores.com//assets/images/promotions/Free-Gift-Card.jpg (http://artecindustries.3dcartstores.com//)

Pretty simple, buy over $100 of our parts get a free $10 gift certificate e-mailed to you. If you go over $250, you get a $25 card instead and so on for $500 ($50 GC), $1000 ($100 GC), and $1500 or more ($150). Ends 12/31/2011.

For a complete listing of our parts, click here (http://artecindustries.3dcartstores.com//ARTEC-PRODUCTS_c_132.html).

Thanks for all the orders from the past two days. Lots of free gift cards were emailed out.

These are in stock and ready to ship.

u offer a complete histeer or crossover kit. price shipped on both. and for just arms. 97383

I don't have a complete crossover kit yet, though it is in the works. Sending PM on arms.

hey guys when i added the arms to my cart on your site, it added the price of the $25.00 gift card to the order and then discounted it. sure its a glitch but might want to look into it.

hey guys when i added the arms to my cart on your site, it added the price of the $25.00 gift card to the order and then discounted it. sure its a glitch but might want to look into it.

Yes it has to add the $25 to the cart for the GC to be worth anything when you redeem it, but it also simultaneously discounts the value of the GC from the total order, so your total would be the total of just the parts you are ordering.

The ULTIMATE D60 HIGH STEER ARMS are the new DEAL OF THE WEEK. SAVE 15% ($48) on the best arms on the market. Plus you get a FREE $25 GIFT CARD with our current December promo. GET IT NOW. SALE ENDS SUNDAY NIGHT (12/18) AT 11:59 pm (the countdown timer is wrong).

https://artecindustries.3dcartstores.com/assets/images/promotions/HSADOTW.jpg

https://artecindustries.3dcartstores.com/assets/images/highsteer/d60-knuckle-assembly-features3.jpg (http://artecindustries.3dcartstores.com/Ultimate-Dana-60-High-Steer-Arms--Pair_p_154.html)

Get these while they are only $271.99 only 4 DAYS LEFT.

Get these NOW, the sale will be over on Monday morning early.

I'll extend the sale until noon PST. Lots in stock and ready to ship. If you get it in today, the package will still make it by Christmas unless its on the east coast.

Since the countdown timer was messed up and its showing that the sale ends in a little under two days from now (instead of midnight last night), we've decided to continue the sale until the countdown timer runs out. Sorry for the confusion.

GET THESE NOW before the time really runs out.

These are in stock and ready to ship out.

LESS THAN 24 hrs left to get this sweet deal. SHIPPING OUT IMMEDIATELY TOO!

These are in stock and ready to ship.

I just logged on to check and see if you guys are having a christmas sale on these and find out I missed that deal, impeccable timing.

So, you having a christmas sale? I'm ready to buy a set of arms, still a little on the fence on brand but my buddy has these and they sure look nice.

Thanks

Will the arms work with H1 rims with the 3.5 BS. Using the DS bolt.

I just logged on to check and see if you guys are having a christmas sale on these and find out I missed that deal, impeccable timing.

So, you having a christmas sale? I'm ready to buy a set of arms, still a little on the fence on brand but my buddy has these and they sure look nice.

Thanks
See next post ;)

Will the arms work with H1 rims with the 3.5 BS. Using the DS bolt.

If they are recentered H1s with 4.75" or less BS, they should work just fine.

Its that time of the year...we need to get rid of some inventory to keep Uncle Sam from making us say UNCLE!

https://artecindustries.3dcartstores.com/assets/images/promotions/year-end-sale.jpg (http://artecindustries.3dcartstores.com/)

You read that right---20% off all Artec Parts! Plus you can use the pirate4x4 coupon on anything not Artec-made for 10% off.

HURRY ENDS 12/31 and there will be NO EXTENSIONS!

WEBSITE LINK (http://artecindustries.3dcartstores.com/)

Machining a really large batch of these right now to keep up with demand from the huge sale. Thanks for all the orders.

These really are the ULTIMATE high steer arms. Basically eliminate stud sheer issues and allow double sheer mounting anywhere between the stock location and the high steer. We know not every build is the same so why use other high steer arms that force your joints to mount in a set location?

shipped to 67212 6bolt keyed with knuckle bolt kit thanks

PM sent.

Bunches of these high steer arms are being snatched up during this sale. Get yours now. We have a huge batch finishing up mid-next week so any new orders will be shipping then. A half week isn't too long to wait when you save this much $$.

Price shipped to CA, 95961. (Standard Chevy knuckles )

PM sent.

FYI, if anyone is looking for an instant quote, our website will have the same prices that we would quote. Its a little difficult to quote when there are several options to choose from and the quote request doesn't include those. We don't mind doing it but for the quickest, most accurate quote, just add the products you want to your shopping cart, enter the pirate4x4 coupon, and enter your zip code in the calculate shipping field. That's exactly what I do when I give a quote.

ONLY TODAY AND TOMORROW REMAINING FOR THE SALE. ACT NOW!

http://artecindustries.3dcartstores.com/High-Steer_c_136.html

LAST DAY of the SALE!

LAST CALL and HAPPY NEW YEAR!!!!!!

Just received my arms yesterday and they kick ass. Nice work. I will definitely be a return customer.:)

Thank you, these arms are now in stock and ready to ship.

need the strongest D60 high steer arms available, well we got em and they are in stock and ready to ship. We also have them for the 6 hole solid knuckles.

http://www.artecindustries.com/assets/images/highsteer/d60-arm-bottom.jpg


Click HERE (http://www.artecindustries.com/Ultimate-Dana-60-High-Steer-Arm--Single_p_155.html) for more information.

Get the ultimate set up, combine our arms with the Reid Racing Bronze Kingpin bushings and you will have the strongest set up available.

http://www.artecindustries.com/Ultimate-Dana-60-High-Steer-Arms--Pair_p_154.html (http://www.artecindustries.com/Ultimate-Dana-60-High-Steer-Arms--Pair_p_154.html)

http://www.artecindustries.com/Dana-60-BRONZE-Upper-Kingpin-Bushing_p_224.html

In stock and ready to ship order before 2pm and they will ship out same day.

I love mine! Thank you guys for the awesome product!

http://thedoubleduke.com/pics/SilverRubicon/Jeepbuild/14Boltfront/1.23.12/PSartec.jpg

I love mine! Thank you guys for the awesome product!

http://thedoubleduke.com/pics/SilverRubicon/Jeepbuild/14Boltfront/1.23.12/PSartec.jpg

Strongest set up available. In stock and ready to ship out.

These arms are in stock and ready to ship out. Here is a pic of some that were clear zinked.

BLING BLING

http://a1.sphotos.ak.fbcdn.net/hphotos-ak-ash4/422249_311497272235965_100526703333024_914473_8762 77176_n.jpg

Some more install pics, this time paired up with Howe Performance Steering.

http://a2.sphotos.ak.fbcdn.net/hphotos-ak-ash4/408018_312442148808144_836574608_n.jpg

In stock and ready to ship!

http://a7.sphotos.ak.fbcdn.net/hphotos-ak-ash4/419284_317374698314889_100526703333024_926727_9616 80521_n.jpg

Another huge batch of these rolling off the machines in the next day or two. We still have a few left on the shelf too. Thanks for keeping us busy. These go so fast, it seems one of our mills is dedicated just to these high steer arms.

Truly the ultimate high steer arms that can handle abuse like this and still be like new and ready to run the next race. And the best part is they are in stock and ready to ship out.

King of the Hammers 2012 - Mike Klensin Spectacular Crash/Finish - TAILGUNNER MEDIA - YouTube (http://www.youtube.com/watch?v=w5YxT-ouBDU&feature=youtu.be)

In stock and ready to ship.

Our Ultimate High Steer arms are about to get even better stay tuned!!!!!!!!!!!

Lots of arms in stock. Oh and THEY ARE NOW CLEAR ZINC PLATED! The coating makes these not only very durable to the elements, but seriously good looking.

http://a3.sphotos.ak.fbcdn.net/hphotos-ak-ash4/416786_337017349683957_100526703333024_975403_2782 45912_n.jpg (https://artecindustries.3dcartstores.com/Ultimate-Dana-60-High-Steer-Arms--Pair_p_154.html)

The clear zinc on these looks almost like chrome. Get the ULTIMATE ARMS and add a little bling.
http://artecindustries.3dcartstores.com/Ultimate-Dana-60-High-Steer-Arms--Pair_p_154.html

Damn those look good plated. I may have to get my old ones done that way.

Damn those look good plated. I may have to get my old ones done that way.

We're taking another batch to plating in a couple days. If you want, send them to me and I'll put them in.

trying to order the arms, but the pirate4x4 discount isn't working or at least it's not working for me---what's up???

chris

trying to order the arms, but the pirate4x4 discount isn't working or at least it's not working for me---what's up???

chris

Its because they're on sale for 15% off already which is the better deal of the two.

thought that could be it, but just wanted to double check--thanks...chris

Got another call from someone who ripped their Brand X steering arm off. Don't let it happen to you. Get the Ultimate Dana 60 High Steer Arms!

my order was placed and am just waiting arrival of these arms--thanks--chris

Got another call from someone who ripped their Brand X steering arm off. Don't let it happen to you. Get the Ultimate Dana 60 High Steer Arms!

I bet that was me. Yup, after seeing the Artec setup at KOH we decided to swap over to the Artec Ultimate Steering Arms on our U4 car. The setup just makes so much sense and is a clean way to add serious beef.

Thanks, Nate.

Just got a batch back from zinc plating today. Thanks to those who've been patiently waiting, your orders will be shipping soon.

got my arms the other day and slapped them on, very nice product--thanks again.....chris

got my arms the other day and slapped them on, very nice product--thanks again.....chris

Thanks, when you get chance, post up some pics.

will do on the pics..

I've been on the fence about your front full hydro mount and would love to have it and it would possibly make my life a tad simpler, as it looks like it locates the ram nicely. Also I have the Trail Gear kit and since you don't state that TG ram fits along with the extra $$$ I decided not to buy it and monkey with it. I know where there's a will there's a way, but my will is slipping these days ....chris

do you have this in stock???

Dana 60 Full Hydro RAM MOUNT ONLY
Item Id: TRD60F09R

chris

I hope you have it in stock, as i just bought it and would love to have it by the weekend if possible. I guess my will to fab up a new mount since the TG one won't work(toyota set up vs '85 ford dana 60) and I need more tube and plate is less than my will to buy your ram mount and I'll adapt the mounts for the TG ram if they don't line up---chris

Ultimate Arms in stock and ready to ship.

Price for a pair of arms keyed for solid knuckles shipped to 34472. Thanks

Price for a pair of arms keyed for solid knuckles shipped to 34472. Thanks

PM on its way.

FYI to everyone. If you'd like the most immediate quote, we have it built right into our shopping cart. Simply add the products you'd like in the shopping cart. Then enter pirate4x4 in the coupon section and hit go. Then enter your zip in the shipping calculator. That's all we do when you send you back a quote. Its very accurate and the shipping won't change from the calculator to the actual checkout like some systems do.

I don't mind doing quotes but usually you'll know your answer within a couple seconds rather than waiting for us to reply. Also, I've included quick links to our most popular product in the signature below so you'll be able to access our products quickly.

just want to say thanks for getting me the ram mount so quick last week--I got it installed this weekend and it's all painted up and looks great--of course I did some modifications to it to fit the Trail Gear DE ram I'm using and for my panhard bar(no room on a willys to do things normal), but all in all a super great product--thanks again.....chris

price on the high steer arms for a chevy d60 and the bolt kit for the dual sheer set up to 78501 please!

D60 arms in stock and ready to ship!!!!!!!

5 bolt and Solid 6 bolt arms in stock and ready to ship out.

Lots of arms going out! Thanks for all the orders today.

Lots of these in stock and ready to ship. In fact, we have one mill that is completely dedicated to just making these high steer arms so we can always be in stock. Its crazy how many of these go out the door. These really are the ULTIMATE Dana 60 high steer arms. When you're done breaking those other high steer arms, sheering studs, and cracking knuckles and are ready adjustable double sheer and no worries, come see us.

ARTEC ULTIMATE HIGH STEER ARMS FOR DANA 60 (http://artecindustries.3dcartstores.com/High-Steer_c_136.html)

Lots of arms in stock and ready to ship. These arms are truly the ultimate D60 arms and they come zink plated now.

Don't forget about our sale this weekend.

https://artecindustries.3dcartstores.com/assets/images/promotions/Memorial-sale-card1.jpg