Dana 60 Springless High Steer Arm. These are CNC plasma cut from 3/4 A36 Steel and CNC Machined. This style of arm will replace your cap and spring of your top kingpin. This will allow you to asjust the preload of the kingpin bushing. Includes 1 arm,1 grease fitting, 1 Set screw with jam nut, and 1 kingpin washer. I can drill and or taper to any specs needed for extra. Please feel free to email with any questions.

$50 each or $95 for a pair

$8.95 Shipping for single or pair!!


Paypal address is fourwheelsupply@yahoo.com


http://i43.photobucket.com/albums/e362/butchcj-8/IMG00362-20110115-1259.jpg

Just added a cap to our list of products. $40 each or $75 a pair. Or mix and match with an arm.

http://i43.photobucket.com/albums/e362/butchcj-8/IMG00375-20110214-1018.jpg



Now in stock! Double ended arms!!! 75$ shipped. (will combine shipping on pairs)

http://i43.photobucket.com/albums/e362/butchcj-8/IMG00415-20110518-1327.jpg

http://i43.photobucket.com/albums/e362/butchcj-8/IMG00417-20110518-1328.jpg

Thanks for all the orders!! Keep them coming!!!

Can you do just springless caps also? I only need one steering arm and a cap for the other side

I'm sure they would be pretty popular for those of us with d60's trying to get rid of death wobble

Can you do just springless caps also? I only need one steering arm and a cap for the other side

I'm sure they would be pretty popular for those of us with d60's trying to get rid of death wobble



We have them in the works. Keep your eyes open. We are working on new products all the time. We are just waiting on a few hours of downtime on one of our machines to run them. We are running at full capacity now and I just try and throw these new products in when I can. But I usually run 50-100 or so of them so we dont run out!! I will post here first thing when they are ready!!! Thanks

Butch

Can you do just springless caps also? I only need one steering arm and a cap for the other side

I'm sure they would be pretty popular for those of us with d60's trying to get rid of death wobble

I've got Cash-n-hand waiting for the "arm and cap". PM me ASAP.

Arm and cap, arm tapered and drilled to accept 1 ton GM Tie rod end. Arm and cap shipped to 84119

so do these just bolt on what else is need to install them?

will they clear H2 rims?

I've got Cash-n-hand waiting for the "arm and cap". PM me ASAP.

Me too

I'm thinking about just getting two arms and cutting one off

I should have caps available sometime next week. I will pm all when they are ready! Thanks for the interest!

so do these just bolt on what else is need to install them?

will they clear H2 rims?


You shouldnt need anything to install. Unless you wanted to replace or upgrade your your studs/bolts. And I personally havent run them with H2 Wheels so I cant be for sure on that.

Thanks

Whats the overall length on these arms? Saw these after I saw your other ones. I like these and I'm in the market for some!

Do You just sell spacers? If so how much for a pair shipped to moab 84532?

Glad to see your product. About time someone makes a affordable, simple Dana 60 high steer arm.

Nat

also interested, yes what is the length can get 8" from cntr of bolts to tie rod hole

Whats the overall length on these arms? Saw these after I saw your other ones. I like these and I'm in the market for some!

Overall lenght is around 10.5" Center of kingpin to center of radius on other end is 7.5" thanks

Do You just sell spacers? If so how much for a pair shipped to moab 84532?

Not at this time. But That is something we will be looking into. thanks

Glad to see your product. About time someone makes a affordable, simple Dana 60 high steer arm.

Nat

Thanks!

also interested, yes what is the length can get 8" from cntr of bolts to tie rod hole

I designed them to be 7.5" from center to center. But we might be able to stretch the tie rod hole out to 7.75" or so. It has a 1" radius on that end so you could scoot the hole out a little. if you needed it.

where are you located?

where are you located?

My shop is in Richlands VA in the southwestern tip of VA

Can a get a quote for 2 arms (driver/passenger) both drilled and tapered for GM 1 ton TREs shipped to 97113. Thanks!

Can a get a quote for 2 arms (driver/passenger) both drilled and tapered for GM 1 ton TREs shipped to 97113. Thanks!


123.95 shipped to your door. Thanks

How's the caps comin" along?

i may have missed it but how do i buy these? just paypoal ya and let ya know what i need?

interested in cap and passenger are too... 97267

Thanks!

Guys. He sound like he is really busy trying to complete the caps. (I got an email response from the owner) which he said will be next week. So, he should respond back to you today sometime.

Yep, paypal with what you want in the comment section.

sorry for the late response guys. Been super swamped here lately!!!! Which is good this day and age. Anyways...... Caps are scheduled to be run on monday. If you need to order you can paypal to the address in the first post. Just be sure to put in the message what you need.

Caps will be 40$ each with hardware.

Shipping will be 8.954 for single or pair.

I have 50 caps to be run on monday so I can ship asap.

Thanks for all orders!!!

any thoughts on an arm that has a angle on it? for a tierod end/// yours look like the heim joint hook ups.
like

http://eastcoastgearsupply.com/images/F59213.jpg

We have some arms with the ackerman angle built in in the works. Probably a month or so away. We are developing new products all the time. But we have to squeeze them in between production runs on our machines. thanks for the interest!

I ordered a set of arms form him. He shipped them out quickly. It was a easy transaction.

They are great for the price. A little paint and they will be on my rig this weekend

ordered a set of arms thanks money sent :D

eta?

ordered a set of arms thanks money sent :D

eta?

Just got the money! Thanks will ship today!!!! USPS Priority Flat Rate!

Just got the money! Thanks will ship today!!!! USPS Priority Flat Rate!

ill let ya know how they clear the H2s maybe with pics if i get a chance im really hopin they do clear lol

Awesome. good luck to ya.

I need a quote on one arm drilled for gm 1ton tierod and one cap shipped to 42101. Thanks

I need a quote on one arm drilled for gm 1ton tierod and one cap shipped to 42101. Thanks

50 arm 40 cap 10 drill/taper 8.95 shipping= 108.95

You can paypal to fourwheelsupply@yahoo.com

Thanks

Just got my drilled, arm, and cap pair. Nice beef, and priced right.
Damn USPS! Package got here today, super fast. but, it was busted open at the bottom and contents spilled out. Somehow, none of the parts were lost in transit. Great transaction other than that. Thanks Ryan!

When you can get these things angled, do you know how much they will be? Assuming you get them out in early march-ish, I might be interested in 2 pair of them, since the price seems to be right.

got the arms look awesome thanks for the speedy shipping :smokin:

When you can get these things angled, do you know how much they will be? Assuming you get them out in early march-ish, I might be interested in 2 pair of them, since the price seems to be right.

^^^^^^

What he said, but only one set.

Just to let yall know. We have them in the works. Keep your eyes open. Thanks for all your input and orders!!

ttt

My memory isn't what it once was, if you could PM me when you come out with them I will most likely reward you with an order for 2 pair.

PM sent

I like the ability to adjust the pre-load on the kingpins!

I have a crew cab V3500 that will be my DD and my tow rig, I am going to be converting my Dana 60HD to a crossover steering system, do you think these top plates are going to be well suited for my application?

I like the ability to adjust the pre-load on the kingpins!

I have a crew cab V3500 that will be my DD and my tow rig, I am going to be converting my Dana 60HD to a crossover steering system, do you think these top plates are going to be well suited for my application?



Just what you need!!! Let me know when you are ready to order.

Just what you need!!! Let me know when you are ready to order.

Sweet! As soon as I start tearing everything apart, you will get a phone call! Also, not trying to get too far off track, but do you have a complete crossover system you sell as well?

Sweet! As soon as I start tearing everything apart, you will get a phone call! Also, not trying to get too far off track, but do you have a complete crossover system you sell as well?


As of right now we do not offer one, but the request's for them have been rolling in so keep your eyes open we just might add them to our list. thanks

as of right now we do not offer a complete kit. But there is a great request for them so we will probably add them in the future.

PM Sent

Thanks for all the orders, these are flying off the shelf!!!!

Any plans for making any arms for the rockwells?

Thanks

Nat

Any plans for making any arms for the rockwells?

Thanks

Nat



They are on the list, Just havent found a semi local steering rockwell to get my hands on to engineer one.

So if anyone wants to send me their knuckle I will make them a pair for free!!!!

Anyone have any pics of these arms mounted up.

Anyone have any pics of these arms mounted up.



This is the only one I have as of today. And its a cell pic from a customer running stock H1's

I will try and shoot one in the morning of one mounted to a knuckle I have in the shop..

http://i43.photobucket.com/albums/e362/butchcj-8/0219111533a.jpg

Thanks for all the orders!!!

ttt

New options listed in first post!!!!


check them out

how much for pair of arms gm 1ton tie rod ends with correct ackerman angle to 95623

is this the "all the time" price or sale?

how much for pair of arms gm 1ton tie rod ends with correct ackerman angle to 95623



140 to your door. 4-5 lead time on milling, drilling and reaming.

thanks

is this the "all the time" price or sale?



yes sir!!!

New options and pics listed in first post!!

New options and pics listed in first post!!

Can you do a set of Rear steer behind Knuckle's Ackerman & TRE's

Kinda like these:

http://i150.photobucket.com/albums/s116/boulderwallguy/1994%20Bronco%20SAS%20Longarm%20Coil/Dana60Arms.jpg

If So I need 2 sets shipped to 48384

Can you do a set of Rear steer behind Knuckle's Ackerman & TRE's

Kinda like these:

http://i150.photobucket.com/albums/s116/boulderwallguy/1994%20Bronco%20SAS%20Longarm%20Coil/Dana60Arms.jpg

If So I need 2 sets shipped to 48384



I have material ordered for doing double ended arms. Should be a week or two. thanks

I have material ordered for doing double ended arms. Should be a week or two. thanks

Ok cool let me know

Could I get a quote for 2 arms with a 10* angle and a 3/4" hole. Do all of the arms have the 5th hole now?

Quote on 2 arms, angle milled, 3/4 hole. shipped to 80104
And a rough estimate on when they would ship??
Thanks

Could I get a quote for 2 arms with a 10* angle and a 3/4" hole. Do all of the arms have the 5th hole now?



I have a few arms left with just 4 holes, the next batch will have 5 holes.

133.95 shipped 2 day lead time for options.

Quote on 2 arms, angle milled, 3/4 hole. shipped to 80104
And a rough estimate on when they would ship??
Thanks

133.95 shipped 2 day lead time for options.

I realized a double arm on one side would work best for my application. How are the double arms coming along.

any idea when or if you will offer complete kits that would include TRE/HIEMS and hardware? if so i would get one today!

I realized a double arm on one side would work best for my application. How are the double arms coming along.


Havent got to them yet. Been swamped with crazy production deadlines here lately. Ill try and get them worked in, been working 7 a week trying to keep up.

any idea when or if you will offer complete kits that would include TRE/HIEMS and hardware? if so i would get one today!



dont have a good source for heims, but I can offer GM 1 ton TRE's .

dont have a good source for heims, but I can offer GM 1 ton TRE's .

I believe Dan over at Ruff Stuff could fix that.

Nat

TREs work for me:D. what would a complete kit run for crossover on a Ford 60? and what all would it include?

Can you make offset arms to clear h1 rims?

Can you make offset arms to clear h1 rims?


These will clear, There is a post of a pic of a customer that installed them with H1's. Look in earlier post. Let me know if I can help.

This is the only one I have as of today. And its a cell pic from a customer running stock H1's

I will try and shoot one in the morning of one mounted to a knuckle I have in the shop..

http://i43.photobucket.com/albums/e362/butchcj-8/0219111533a.jpg

if thats the pic i sent you which i think it is thats a stock H2 rim not H1 fyi

sorry I thought they were H1's

I sent you a pm about shipping to Canada. How is that coming along.

Nat

I sent you a pm about shipping to Canada. How is that coming along.

Nat

Im sorry, I thought I had replied to all PM's Shipping to canada on a pair of arms will be 26.95$ Thanks

Got these installed today. Awesome product.

Only suggestion would be to put a little taper in the holes for cone nuts so they seat right. I had to do that to my arms.

Pics of em installed. 15x12 2.5bs

YES I KNOW I ONLY HAVE 3 STUDS ON ARM, YES I KNOW I AM MISSING THE ZERK ON MY TRE

http://i142.photobucket.com/albums/r95/sargin311/IMAG0140.jpg
http://i142.photobucket.com/albums/r95/sargin311/IMAG0143.jpg
http://i142.photobucket.com/albums/r95/sargin311/IMAG0144.jpg
http://i142.photobucket.com/albums/r95/sargin311/IMAG0145.jpg
http://i142.photobucket.com/albums/r95/sargin311/IMAG0146.jpg

Any progress on the double arm?

hope this great price and product is still available looking forward to order next month

Yep still avail!! running new batch today!! All arms will now come standard with 5th hole for reid knuckles no extra! Also Double ended now in stock!!!! 75$ shipped each!! Pics added to top post

You've got money! Just sent for springless Dana 60 high steer arms.

You've got money! Just sent for springless Dana 60 high steer arms.



Awesome!!! thanks for the purchase!!!

Arms will ship in the AM!!!!

Thanks for all the orders!!!!! Pirate members are the best!!!!

Thanks for the arms. Got them today

Can I get a price on a single arm machined with the 10* angle/drilled for a chevy 1 ton TRE (passenger side) and a springless cap shipped to 03103 please?

Can I get a price on a single arm machined with the 10* angle/drilled for a chevy 1 ton TRE (passenger side) and a springless cap shipped to 03103 please?



100$ shipped 3 day turnaround for options. Thanks

100$ shipped 3 day turnaround for options. Thanks

Can I get a price on a single arm machined with the 10* angle/drilled for a chevy 1 ton TRE (passenger side) and a springless cap shipped to 03103 please?

Payment sent

Can I get a price on a single arm machined with the 10* angle/drilled for a chevy 1 ton TRE (passenger side) and a springless cap shipped to 21157 please?
Also, just picked up this truck and its my first D60, is there any special knowledge i need to adjust the set screw and/or removing the spring?

Can I get a price on a single arm machined with the 10* angle/drilled for a chevy 1 ton TRE (passenger side) and a springless cap shipped to 21157 please?
Also, just picked up this truck and its my first D60, is there any special knowledge i need to adjust the set screw and/or removing the spring?



100$ shipped. gonna be next week for delivery. sold last one today! Scheduled to run more mid next week. Let me know if you are interested.

Sent you a couple PMS. Haven't heard anything back yet though.

sent you a couple pms. Haven't heard anything back yet though.



pm sent

How much for a arm with 1 hole reamed to chevy tre shipped to 26582? Thanks

How much for a arm with 1 hole reamed to chevy tre shipped to 26582? Thanks



68.95 to your door.

Quote on 2 arms, drilled, machined with chevy tre in both to 95444

Quote on 2 arms, drilled, machined with chevy tre in both to 95444



140$ to your door. 2-3 day lead time for options. Thanks

when I installed the arms with all new king pin parts with the washers under the arms they bind and cant turn the knuckles now, my arms dont have pocket machined for washer, any tips on what to do other then machine the arms, I dont have access to a mill.

need pricing for a pair of arms drilled for hiems do i need milling also??

also for 1 pass side arm drilled and machined for tie rod and one cap.

shipped to 49444

also do you have the stud kit for them?

when I installed the arms with all new king pin parts with the washers under the arms they bind and cant turn the knuckles now, my arms dont have pocket machined for washer, any tips on what to do other then machine the arms, I dont have access to a mill.



Easiest thing to do is to get a thinner "fender" style washer. If that dosent work I will take them back and send you a new set with the milled recess to take care of the problem. I cant quite figure out why some guys are having this problem and some are not? Anyways. Just let me know what you want to do.


Thanks

need pricing for a pair of arms drilled for hiems do i need milling also??

also for 1 pass side arm drilled and machined for tie rod and one cap.

shipped to 49444

also do you have the stud kit for them?



Pair of arms drilled will be 113.95 shipped

One arm and cap drilled and milled will be 100 to your door.

Sorry no stud kits as of yet. Thanks

Pair of arms drilled will be 113.95 shipped

One arm and cap drilled and milled will be 100 to your door.

Sorry no stud kits as of yet. Thanks

payment has been sent for both 213.95

thank you andrew

payment has been sent for both 213.95

thank you andrew



Got it! Thanks

Thanks for all orders!!!!

These are flying off the shelf!!!

:smokin: I sent payment for my arms did you get it and how long will they take? thanks jay

:smokin: I sent payment for my arms did you get it and how long will they take? thanks jay

Havent seen it yet. Did y ou paypal?

yes paypal to 4wheelsupply @yahoo
YA I SEE FOURWHEEEL NOT 4 WHEELSUPPLY I FIXED IT SHOULD BE THERE LET ME KNOW

Hello,

How much for 2 dana 60 springless arms with 10 degree angle and a hole tapped for 3/4" NC thread?

Thanks

Do you or anyone else who has bought these know if they will clear stock h1 wheels?

Do you or anyone else who has bought these know if they will clear stock h1 wheels?

brantb, This has been covered check out page 3.

brantb, This has been covered check out page 3.

but if you check out page 4, i think it is the person who sent in the photo saying that they are h2 wheels. I would just like to get confirmation one way or the other.

PM sent

can you please let me know what happened to the arms you shipped....
i need to get them soon

I want a pair of arms how do I order them

I want a pair of arms how do I order them

PM me what you need and I will quote and you can paypal! thanks

Hello,

How much for 2 dana 60 springless arms with 10 degree angle and a hole tapped for 3/4" NC thread?

Thanks



Sorry for late reply, Shop has been overwhealmed here lately

$140 to your door. 3-5 day turnaround on adding options. Thanks

:D thanks for the great arms they look sweet ..... cant wait to get them on:grinpimp:

price on 1 springless cap, an one passenger side springless arm with angle , are these drilled or tre or heims? if not how much for that as well

115.00 shipped

New batch fresh off the mill today!! Get them while they are hot!!!

http://i43.photobucket.com/albums/e362/butchcj-8/D60arm.jpg

Will they clear a Stock H1 rim?

Will they clear a Stock H1 rim?

Not 100% sure. I have sold a few sets to guys that ordered with intensions of running them with H1's but I got no feedback whether they worked or not.

Can you do a set of Rear steer behind Knuckle's, Ackerman? Kinda like these:

http://i150.photobucket.com/albums/s116/boulderwallguy/1994%20Bronco%20SAS%20Longarm%20Coil/Dana60Arms.jpg


Set up for TRE's.

1 set shipped to 15219,
Thanks!

Yes, I have double and single arms in stock and can add the 10* milling and TRE for for $175 shipped. 2-3 days lead time for adding options



Can you do a set of Rear steer behind Knuckle's, Ackerman? Kinda like these:

http://i150.photobucket.com/albums/s116/boulderwallguy/1994%20Bronco%20SAS%20Longarm%20Coil/Dana60Arms.jpg


Set up for TRE's.

1 set shipped to 15219,
Thanks!

Woundering if you have a complete high steer kit for 79 ford d 60 yet? If so how much sent to 05680 thanks.

Pair of arms with tre. And Ackerman angle to 95623

Woundering if you have a complete high steer kit for 79 ford d 60 yet? If so how much sent to 05680 thanks.

No kits yet. Just arms.

Pair of arms with tre. And Ackerman angle to 95623


133.95 shipped 2-3 days turnaround

Money sent

How much for 79 ford Dana 60 arms tre and Ackerman sent to 05680 and could you give me the measurements from center of kingpin to center of both tre holes on pass. Arm. Thanks

was wondering if you could do a passenger side arm with the taper on the bottom side (for a heim mounted under the arm for clearance) with a fine thread 5/8" hole set in line with the outer king pin bolts (not in line with the kingpin like it appears the arms are) 5" from the kingpin pivot for proper akerman angle and to match my pitman arm. let me know if you need a drawing of what I'm talking about. I'd also be looking for a springless cap for the driver side. shipped to 01128

was wondering if you could do a passenger side arm with the taper on the bottom side (for a heim mounted under the arm for clearance) with a fine thread 5/8" hole set in line with the outer king pin bolts (not in line with the kingpin like it appears the arms are) 5" from the kingpin pivot for proper akerman angle and to match my pitman arm. let me know if you need a drawing of what I'm talking about. I'd also be looking for a springless cap for the driver side. shipped to 01128



Could do it all but the bolts lined up with the outside kingpin bolts. The arms are designed with the linkage hole to be in the center. If that works I will give you a quote. Thansk

Waiting for a price so I can send money thanks

Waiting for a price so I can send money thanks

Sorry! Missed your post. 133.95$ shipped. 2-3 day turnaround.

Could do it all but the bolts lined up with the outside kingpin bolts. The arms are designed with the linkage hole to be in the center. If that works I will give you a quote. Thansk

I could make it work. How much?

I could make it work. How much?



$133.95 shipped 2-3 day turnaround. Thanks

Ok, sorry if I'm just confused. A couple people have asked about Ackermann Geometry. For example, Wicked Wrangler asked:

How much for 79 ford Dana 60 arms tre and Ackerman sent to 05680

With the response from 4WheelSupply being:

Sorry! Missed your post. 133.95$ shipped. 2-3 day turnaround.

This makes it sound like you CAN do "Ackermann" style arms. But when asked if you can put the link ends in line with the outer kingpin bolts by mattamd_xp:

hole set in line with the outer king pin bolts (not in line with the kingpin like it appears the arms are) 5" from the kingpin pivot for proper akerman angle

The response by 4WheelSupply was:

Could do it all but the bolts lined up with the outside kingpin bolts. The arms are designed with the linkage hole to be in the center.

This sounds like you CANT do "Ackermann" style arms...

Again, forgive me if I am just confused, but to my knowledge the basic concept of Ackermann steering requires that if the tie rod is in front of the steering axle, it must be slightly longer than the distance between the kingpins, and if the tie rod is behind the steering axle, it must be slightly shorter than the distance between the kingpins.(Wikipedia Ackermann (http://en.wikipedia.org/wiki/Ackermann_steering_geometry))

Obviously that is an oversimplified explanation of Ackermann Geometry but my point is this; The arms pictured in the first post appear to show the tre holes being in line with the kingpin. This would make the tie rod parallel with the kingpins and therefor NOT be Ackermann Geometry. Do you offer an additional version that is not pictured that DOES offer Ackermann Geometry with the holes for the Tie Rod being more in line with the outer kingpin bolts?

As far as I've found, there are only three types of Ackermann steering for Dana 60's; Factory (the cast mounts on the outer knuckles), Artec Industries High Steer Arms (including the double sheer tie rod kit they're $365ish bucks), and NorthWest Fabworks High Steer Arms ($298 per set).

There are several threads here on Pirate and elsewhere arguing Ackermann vs non-Ackermann blah, blah, blah. Just my opinion here, but at $95 plus drilling for TRE and shipping who really cares if they're Ackermann or not, 4WheelSupply's arms appear to be a great deal!

They are definitely not setup to include ackermann angle on these arms. I think people are confusing the taper milled into the arm to compensate for the taper of the factory knuckles.

Sent PM

Sorry, 133.95 is for a pair. So you are correct with your price. Thanks




Is it really $25 extra for the threaded hole? Or is that the price for 2 arms rather than 1 arm and 1 cap?
the total would seem to be $108.95 from the price list in your first post:

$50 each or $95 for a pair =$50 for single passenger side arm arm

$8.95 Shipping for single or pair!! =$8.95 shipping

Just added a cap to our list of products. $40 each or $75 a pair. Or mix and match with an arm. =$40 for the driver side cap

Option 2 is milling the 10* angle into the arms. (pic coming soon) will be $10 for single or $15 for the pair. Which includes your choice of linkage hole i.e. heim or tre. =$10 for the 10* angle milled on the underside of the passenger side arm and the hole for the bolt ($25 more for 5/8" fine threaded over straight hole??? :eek:)

total I got was 50+8.95+40+10=$108.95 Let me know which price is the correct one :homer:

Sorry, 133.95 is for a pair. So you are correct with your price. Thanks

Thanks, PM incoming :smokin:

Getting ready to send your money. Just one question is the passenger side arm drilled with two holes for a separate tierod and drag link or is it just one hole for the y set up? Thanks

Getting ready to send your money. Just one question is the passenger side arm drilled with two holes for a separate tierod and drag link or is it just one hole for the y set up? Thanks



I can do it either way. I only quoted one hole. an extra $5 for the extra hole. Thanks

Thanks, PM incoming :smokin:

Payment sent per PM! Awesome service :smokin:

what do you recomend on studs? grade 8 bolts or arp studs?

Paymnt sent...Awsome prices!!!

what do you recomend on studs? grade 8 bolts or arp studs?

Grade 8's are good enough but ARP's will be better.

Very happy with my arms and customer service is awesome

I finally sent the money. For arms drilled and tapered for chevy 1 ton tres with Ackerman angle and 2 holes on passger side arm. Please let me know if you got the money. Thanks

I finally sent the money. For arms drilled and tapered for chevy 1 ton tres with Ackerman angle and 2 holes on passger side arm. Please let me know if you got the money. Thanks



Got it. will ship Monday. Thanks

I ordered arms from you with pass. Side drilled with two holes one for drag one for tie rod. The chevy one ton drag link ends and tie rod ends have diffent tapper so i was woundering if you tapered the holes different as well or am I going to have to reem them? Thanks

I ordered arms from you with pass. Side drilled with two holes one for drag one for tie rod. The chevy one ton drag link ends and tie rod ends have diffent tapper so i was woundering if you tapered the holes different as well or am I going to have to reem them? Thanks



I tapered them all for TRE wasnt told any different. Shipping today

Still waiting for a reply to my PM's

ttt

ttt

I bought a set of arms from you drill for separate drag and tie on the pass side for my 79 ford d60 and I got them on today. They seem like they are drilled wrong the tie rod holes are drilled out at the ends and the drag link hole is on the pumpkin side so when you turn it try's to cross. Acouple of my buddy's are running high arms and there drag hole is drill out on the end and tie rods are drilled back alittle on the pumpkin side am I missing something?I have this under a 95 yj with 4" springs and a drop pitman arm.

If at all possible I need to get this resolved by this sat I am leading a two day trail ride. U can call me if u want. 1-802-793-9981 thanks Arthur

If at all possible I need to get this resolved by this sat I am leading a two day trail ride. U can call me if u want. 1-802-793-9981 thanks Arthur



PM Sent!

Pm sent. Let me know if you got it. Thanks for the awesome customer service and super fast response your the best Arthur .

How much for one single and one double milled and drilled for heims? Thanks

How much for one single and one double milled and drilled for heims? Thanks



$140 to your door. 2-3 day turnaround. Thanks

Pm sent with measurements. Best customer service ever!! Thanks

Thanks for all orders!!! Pirate Members are the greatest!!!

Now, my next issue. Take anything other than paypal?

Google checkout?
regular cc processing?

Now, my next issue. Take anything other than paypal?

Google checkout?
regular cc processing?

Paypal is all we currently take at the moment. Not familiar with google check out. Or you can send a check, or money order.

If you don't mind, can you send me 2 paypal requests to rcpfab@gmail.com

one request for 2 arms milled and drilled for 3/4" heims

one request for 1 arm milled and drilled for 3/4" heim and 1 cap

not sure which way I want to go yet

Im pretty sure I can pay with out an account if you send the request.

Thanks
Ryan

If you don't mind, can you send me 2 paypal requests to rcpfab@gmail.com

one request for 2 arms milled and drilled for 3/4" heims

one request for 1 arm milled and drilled for 3/4" heim and 1 cap

not sure which way I want to go yet

Im pretty sure I can pay with out an account if you send the request.

Thanks
Ryan



Coming at ya! 93.95 for 1 arm and one cap milled and drilled

Or 123.95 for 2 single end arms milled and drilled.

I have a few arms milled and drilled on the shelf already so I can ship asap.

Could you tell me what the measurements are for your tie rod holes and drag link hole from center of the king pin? Is there a certain pitman arm or length center to center that works well with your arms? Thanks

Curious... Is youre pitman arm the same center to center of holes as your crossover arms hole to center of king pin? It appears that they are not and I had the understanding that that would cause you not to have full turning radius and thats what Im trying to avoid. Also what did you use to taper the holes? Thanks

Curious... Is youre pitman arm the same center to center of holes as your crossover arms hole to center of king pin? It appears that they are not and I had the understanding that that would cause you not to have full turning radius and thats what Im trying to avoid. Also what did you use to taper the holes? Thanks


Sorry everyone for the confusion on my part, this question was for NorCal about the pictures he posted in thread #83. I have never posted on a board before, only search and read. Ill post pictures somewhere soon to show you guys what all your smart information has helped me build.


Got these installed today. Awesome product.

Only suggestion would be to put a little taper in the holes for cone nuts so they seat right. I had to do that to my arms.

Pics of em installed. 15x12 2.5bs

YES I KNOW I ONLY HAVE 3 STUDS ON ARM, YES I KNOW I AM MISSING THE ZERK ON MY TRE

http://i142.photobucket.com/albums/r95/sargin311/IMAG0140.jpg
http://i142.photobucket.com/albums/r95/sargin311/IMAG0143.jpg
http://i142.photobucket.com/albums/r95/sargin311/IMAG0144.jpg
http://i142.photobucket.com/albums/r95/sargin311/IMAG0145.jpg
http://i142.photobucket.com/albums/r95/sargin311/IMAG0146.jpg

Sorry everyone for the confusion on my part, this question was for NorCal about the pictures he posted in thread #83. I have never posted on a board before, only search and read. Ill post pictures somewhere soon to show you guys what all your smart information has helped me build.

Hey.

Yeah my pitman arm is too short. it sucks. I used a cherokee arm that is 6 or so center to center, when i need 7in. The superlift 1104 is the arm you want

It works but not well.

I used a countersink bit to do the taper for the studs. like one of these

http://ecx.images-amazon.com/images/I/31SNP0QDEML._SL500_AA280_.jpg

Thanks, I almost had all my steering set up with high steer and crossover untill I realized the Skyjacker 78-79 Bronco pitman arm I bought was causing it not to fully turn. After searching high and low for a longer pitman arm I decided today(and I hope I didnt mess up here) to take the arms back off,fill the holes with weld and redrill the holes at 4.5 for the tie rod and 6.5 for the drag link. I havent reinstalled them yet but I hope everything is going to work now.
I seen those countersink bits at Rural King the other day and thought about useing one but wasnt sure if the angle of the taper had to be exact. If it worked for you then that what Im going to use too then. Did you use the 3/4 like the picture or was that just an example? The 3/4 one may be closer to the right taper is what I was thinking. Thanks for your time !

Just paid for the 2 single arms milled and drilled for 3/4" heims. Thanks.

Just paid for the 2 single arms milled and drilled for 3/4" heims. Thanks.



Got it!!! Ships Today!!!! Thanks for the business

Got it!!! Ships Today!!!! Thanks for the business

Thanks, can you email or PM tracking when it goes out?

Ryan

quote for 1 arm drilled for one 5/8" heim to 02747. thanks!

what question? You stated here your question was for NorCal........



Sorry everyone for the confusion on my part, this question was for NorCal about the pictures he posted in thread #83. I have never posted on a board before, only search and read. Ill post pictures somewhere soon to show you guys what all your smart information has helped me build.

quote for 1 arm drilled for one 5/8" heim to 02747. thanks!



$68.95 Shipped

Thanks, can you email or PM tracking when it goes out?

Ryan

PM'd ya tracking info.

Could you tell me what the measurements are for your tie rod holes and drag link hole from center of the king pin? Is there a certain pitman arm or length center to center that works well with your arms? Thanks

Actually this is where I started. Maybe I just didnt realize the process of directing the question at you and thats why you didnt respond. Regardless, I think Ive got er figured out now. Thanks anyway !

ttt

EDIT - awaiting for a replacement set of arms from 4wheelsupply

I have a similar problem. The holes for the TRE are machined perpendicular to the angled surface as they should be. The issue is that the opposite side is not machined parallel to the top face, so the nut doesn't have the correct face to seat against. If the bottom side was machined along with the top, the arm would be too thin for the TRE stud.

PM Sent!

PM Sent!

PM sent, same issue as the guys above!

i am looking to order a set of arms from you and would like to get the hi steer option. will you please post some pics of what these arms look like so i can see how the holes are spaced. it seems like there might be some problems with full end to end steering as i have read from earlier posts. i was looking at some other designs and they put a taper on the top and bottom to account for the angle of the knuckle. it seems that by doing that on this set up the arm would be to thin. have you thought starting with a thicker arm?

PM's answered. Working on a solution.

i am looking to order a set of arms from you and would like to get the hi steer option. will you please post some pics of what these arms look like so i can see how the holes are spaced. it seems like there might be some problems with full end to end steering as i have read from earlier posts. i was looking at some other designs and they put a taper on the top and bottom to account for the angle of the knuckle. it seems that by doing that on this set up the arm would be to thin. have you thought starting with a thicker arm?



Pics are in first post. Milled arms will be on hold until solution is figured out. Should be next week or so. Keep your eyes open! Thanks

pm's answered. Working on a solution.
Pics are in first post. Milled arms will be on hold until solution is figured out. Should be next week or so. Keep your eyes open! Thanks
:)

Can you explain how the springless arms work, and what makes them better?

Thanks
Dima

Any luck getting the replacement arms out? I'm guessing they didn't make it out Friday.

Thanks



No sorry, Had bad luck 10 min before quitting time on friday. Crashed a 3" face mill in the next to last part of a production run that broke spindle belt and blew main fuses. Took until 4pm today to get parts in and back up running. If everything goes right they will leave tommorow.

How much for one springless cap shipped to 49403.

Can you explain how the springless arms work, and what makes them better?

Thanks
Dima

So any explanation? I need to order a set of arms in the next week or so.

thanks
Dima

And day 3 goes by with you logging in and ignoring my posts. Are you sending me a useable set of high steer arms or what?

arms are on the way

So any explanation? I need to order a set of arms in the next week or so.

thanks
Dima

The springless design allows you to replace the tin cap and spring that puts preload on the top kingpin bushing with a adjustable set screw and washer to allow you to adjust the kingpin bushing preload to your desired setting.

Sorry for the delay, really busy this week!

Dude, busy week or not, this is unbelievable. I understand shit happens, but this set of REPLACEMENT arms, to REPLACE the first set you fucked up designing, are even worse.

The "small" "cosmetic" mark you PMed me about is a fucking 3/8" wide 1/4" deep gouge from the broken drill bit.

Then to top it all off you forgot to tap the hole for the grease fittings.

So now I am out $125, and have 2 piles of scrap metal, or I have to waste my time welding in that gouge so the heim will sit flat and tapping the holes.

If your looking for a set of bolt on high steer arms, shop elsewhere, I'm glad I didnt get the D300 clocking ring from you also.



I pm'd you about the gash in the arms only because they were the last two arms on the shelf. I was only trying to get you your arms in the time frame you provided. That arm would have in normal situation went in the scrap bin here, but I sent them to you anyway knowing you needing them to wheel this weekend. As far as the non tapped holes go, that is my fault. I was in a hurry to make usps shipping deadline to get your arms to you. So if you want to bash me and my thread over me rying to take care of you and making a simple mistake in the process go ahead. I think I remember offering you your money back already to take care of this. And that offer still stands.

How much for one springless cap shipped to 49403.



$35 shipped

2 Sets of arms with milled angle and hole for heim joint.

Shipped to 55076

Thanks

2 Sets of arms with milled angle and hole for heim joint.

Shipped to 55076

Thanks



Not offering milling on these arms, found a design flaw. Working on a fix. But still can offer them drilled and shipped for $200 to your door. Thanks

RCP take you bitchfit to the dispute forum, no need for bashing here. must be a mighty big stick up your ass if out of dozens of purchasers you're the only one crying about waiting another week.

Not offering milling on these arms, found a design flaw. Working on a fix. But still can offer them drilled and shipped for $200 to your door. Thanks

That's why I had mine drilled/threaded for the bolt directly. Works great for a rod end with only one side of the arm milled. Lockwire the bolt in place, and you have no problems with just a single side milled. TRE, not so much... May be an idea that some people can use on their arms.

RCP take you bitchfit to the dispute forum, no need for bashing here. must be a mighty big stick up your ass if out of dozens of purchasers you're the only one crying about waiting another week.

removed the posts.

Any progress on the new design.

Any progress on the new design.


Still in the works. Havent had much time to proceed on it here lately, Been covered up with production work. But should be soon.

can you burn some out of 1" and mill them? hate to spend money on cnc work

Just ordered a set. cant wait.

I just placed my order!!! could you please contact me before shipping, my paypal shipping address is all fubared, i needed these arms yesterday, and paypal is not giving me the option to change the address right now

I just placed my order!!! could you please contact me before shipping, my paypal shipping address is all fubared, i needed these arms yesterday, and paypal is not giving me the option to change the address right now


PM or email me the correct shipping address and I will get them out in the AM

I need 1 passenger arm with tie rod hole and 10 degree angle and a cap for the other side. Sent to Odenton 21113 Thanks

Or no angle is fine!

Or no angle is fine!

Yeah, not offering angle milling at this time. But 1 arm drilled and reamed for TRE and one cap will run ya $85 to your door.

Ok, sending paypal
Thanks

can you burn some out of 1" and mill them? hate to spend money on cnc work

?????? ok?

?????? ok?



I can but the price on 2 would be outrageous. We dont burn our own plate in house so the price on just 2 arms burnt from 1" would probably be double the 3/4 because I order 100 burnouts of the 3/4 at a time. I am in the process of developing a new arm that will allow the 10* correction angle made into the arm. It will still be a little while so keep your eyes open. Thanks

Excellent customer service!!!

Thanks,
Bob

Just wondering if you shipped my arms out yet? Been about a week and its the last thing I meed to finish up mu project. Thanks.

Just wondering if you shipped my arms out yet? Been about a week and its the last thing I meed to finish up mu project. Thanks.



Yeah they are on the way, Holidays prob held them up a bit. if you dont see them soon let me know and we will track them

I ordered a set that you milled down for tre and now I see that u are changing the arm do to the angle, can I get a new set when they come out discounted or trade ?

I ordered a set that you milled down for tre and now I see that u are changing the arm do to the angle, can I get a new set when they come out discounted or trade ?




yes, we can figure out something out. Keep your eyes open

I got mine pretty quick. they look good. cant wait to try and break them.

Btt

Any progress on the updated design. I have money burning a hole in my pocket for 2 pairs. :)

Any progress on the updated design. I have money burning a hole in my pocket for 2 pairs. :)

Still in the works! My shop is overloaded with production work right now. So its been hard finding a open space in machine time to get a prototype ran. Looks like i will have a slight slow down after the first of the year for about 2 weeks. Hopefully I can get them going then.

I will be looking at a set of these soon, keep posted on the new design, Thanks

Ordered an arm and cap a while back, just found out last night that the arm was the wrong one. Sent in a PM and am being taken care of.

GREAT customer service! :D

ttt

Bump for you, I will be getting a set as soon as im able.

Just wondering if any more progress has been made on the redesign.

Thanks

I'm looking for a single end shipped to 91941.
Do you have any in stock?
drilled for heim?
How soon can you ship?

Wally

I'm looking for a single end shipped to 91941.
Do you have any in stock?
drilled for heim?
How soon can you ship?

Wally



$58.95 shipped not drilled.
$63.95 drilled 1 place for heim

In stock

$58.95 shipped not drilled.
$63.95 drilled 1 place for heim

In stock

Milled @ 10 deg?

Milled @ 10 deg?



No, Not offering 10* milling at this time.

Wondering if you offer putting the end hole in at 10 deg. instead of milling it. I can get angled shims from McMaster and was thinking I can put one on the top and bottom and tig weld in place. This way no material will be removed from the arm. It'll add about .600" to the thickness of the arm.

Thanks,
Mike

$58.95 shipped not drilled.
$63.95 drilled 1 place for heim

In stockSent you a payment thru paypal

Thanks

Can I get a quote on two single ended arms, one pass, one drivers- both with a single gm 1 ton tre hole( my draglink will be going off tie rod) also both milled with 10* shipped to 95472 thanks sean

Could I get a quote for
1 passenger side double ended arm drilled for 3/4 heim
1 driver side single ended arm drilled for 3/4 heim
Shipped to 76087

Can I get a quote on two single ended arms, one pass, one drivers- both with a single gm 1 ton tre hole( my draglink will be going off tie rod) also both milled with 10* shipped to 95472 thanks sean



Not offering milling at this time on these arms. Had a issue and havent figured it out yet.
but i can offer them to you drilled and tapered for TRE shipped for $125 to your door.

Could I get a quote for
1 passenger side double ended arm drilled for 3/4 heim
1 driver side single ended arm drilled for 3/4 heim
Shipped to 76087



$125 to your door! Thanks

Hey, sorry man I didn't mean to say double ended.
1 driver side drilled for 3/4 heim and
1 passenger side drilled 2 times for high steer and cross over.
To 76087

Need a set with TRE's to 37334. How soon would you ship? Thanks
one tre driver and two on pass.

Hey, sorry man I didn't mean to say double ended.
1 driver side drilled for 3/4 heim and
1 passenger side drilled 2 times for high steer and cross over.
To 76087



No problem. 110 to your door.

Need a set with TRE's to 37334. How soon would you ship? Thanks
one tre driver and two on pass.

Can ship tommorow. 110 to your door. thanks

Can ship tommorow. 110 to your door. thanks

Pm Sent

Thanks for the orders!!!

Pmt sent !!!

Attention!!!!!!!!

I will be out of the shop starting feb 2nd thru feb 13th. I will be out of the country with no cell service or internet. So i wont be able to answer your questions or take orders until the 13th.

Thanks