Well, in the 10 years we have been producing these there have been alot of changes and updates to our line. I thought that we should try and get alot of pictures and all of our options laid out so everyone could see them in one place. And lastly we have reduced our pricing due to steel falling back in line where it was before, so we are passing along the savings to you. Just a better deal all the way around! No fancy gimics or fuzzy numbers to mess w/. Our best price right here for our best customers only on PBB not all over the net!

Shipping we can combine shipping to save you money! We ship via USPS flat rate box when possible.

So here are our specs................ all for $100.00 per cover

- Bolt ring 1/2" thick (we engineer strength where it is needed) we are the only one to manufacture a cover w/ this kind of beef. We do not start w/ thinner mtl weld it unfixtured. Let it warp to kingdom come and then machine it thinner. Only to claim it is thicker than what it ends up being. We build them the correct way the first time around.

- 1 pc machined fill plug, placed for added oil capacity

- 1/4" thick one piece cnc formed cover (why not thicker? read the warranty)

Only at Glo x-tra cost options......................

- Counterbored mount holes (yes all of them, for a clean quality look)

- Integrated drain (ever cross deep water? Drain it out replace fluid and go)

- 1/2" mid plating severe abuse, makes a nice hydro steer mounting point

- Upper Truss Tab (nice for hooking into your homemade truss)

- And everything in between

Models available
Dana 80
Dana 70
Dana 60
Dana 44
14 bolt 10.5" R&P
14 bolt 11.5 R&P
Ford Sterling
Ford 8.8

Warranty ( No B.S. Fine Print )
You break it under use we replace it and add you to the hall of fame as it has never been done in the last 5 years. Our design has been engineered for strength. We weld these the proper way utilizing machined fixtures

Sampling of a customers 14 bolt and D-60 diffs
http://www.pirate4x4.com/forum/attachment.php?attachmentid=259472&d=1156032049

He ordered all of our options as you can see from this pic
http://www.pirate4x4.com/forum/attachment.php?attachmentid=259473&stc=1&d=1156032244

Scroll Down to see what all we offer

ttt

It ain't gonna beat this heat wave but it will protect one of the largest investments on your rig!

Just to make sure everyone knows we have more available options on our covers than any other manufacturer. With two of the most recent available upgrades being show below.

Here is an example of our lower 1/2" plating. This gives you the benefit of the lower 3 portions being a total of 3/4" thick and still staying away from those tight fitting tie rods just in case you are running a stock steering setup.

http://www.greatlakeoffroad.com/images/D/Parts-070-03.jpg

This is an example of the full plating option, which is a combination of our original 1/2" strap upgrade and the lower 1/2" plating

http://www.greatlakeoffroad.com/images/P/Parts-001-01.jpg

Always innovating, we never say the first design is the best you can get and this is a prime example. Thanks for looking. Shawn

Thanks for the orders guys, and note I have a few covers in stock in tread plate option such as the old 14 bolt 10.5 and also the D-60's but some of the others may take a few days for me to get in the blanks. Shawn

I'll take one. For Dana 60, with counter bored mount holes and a drain. Are the bolts included?

No bolts, PM me your phone # or paypal e-mail address and we can get you invoiced and on your way. In stock ready to ship. Thank you for the opportunity!!!!!


I'll take one. For Dana 60, with counter bored mount holes and a drain. Are the bolts included?

Thanks for the order, you should see it as early as Sat but most likely on Monday. Shawn


I'll take one. For Dana 60, with counter bored mount holes and a drain. Are the bolts included?

Glad to see everyone likes the new add on plating options as well as we do!

Thanks for all the orders guys!

ttt

Let me know what you need?

You can buy one at this price or two here on sale for this price>>>>http://www.pirate4x4.com/forum/showthread.php?t=1012655

Sale is over thanks for all the orders PBB!

I realize the sale is over, but do you have a picture of your Dana 60 cover with the truss tab?

I currently do not, I need to build one and get some good pics. If you want to PM me a number I can shoot a picture of the ring with the tab and send it with my phone? If you need more than one cover let me know and I'll see what I can do for you. Thanks Shawn


I realize the sale is over, but do you have a picture of your Dana 60 cover with the truss tab?

ttt

Can you pm me a price on a 60 cover, with counterbored holes,drain plug, and the 1/2 plating upgrade.

Sending the PM now, Thanks Shawn

Can you pm me a price on a 60 cover, with counterbored holes,drain plug, and the 1/2 plating upgrade.

Price on Standard Dana 60 Cover Shipped 77627. Thanks

Still $110.00 delivered, let me know if we can help you out? Thanks Shawn


Price on Standard Dana 60 Cover Shipped 77627. Thanks

ttt

bump

It's almost wheeling weather what do you need?