Dana 60 Springless High Steer Arms Thick Milled

[4WHEELSUPPLY]

These arms are finally avail for sale. I call these my KISS arms. (Keep It Simple Stupid) And I tried to keep these as simple and cost efficient as possible. So arms are not fancy! No fancy engraving of my logo and so on. But they are BEEF! and cheap. Machined from 1 1/4" thick A36 Steel. Milled top and bottom to correct 10* angle offset of knuckle. Springless Design which allows adjustment of top kingpin. Drilled and chamfered 5 places to work with stock or aftermarket knuckles. TRE or Heim attachment holes avail for extra. PM for a quote. Price is $150 for a pair or $80 each to your door. Here are some pics.

paypal address: fourwheelsupply@yahoo.com












Just finished up the double arms. Pics follow. they will work on either driver or pass by turning it around 180*
Price on them are $100 for a single or $175 for a single/dbl pair.

[774x4]

both arms, for stock knuckles with TRE holes for high steer to 91016? first customer discount? JK

[4WHEELSUPPLY]

Originally Posted by 774x4

both arms, for stock knuckles with TRE holes for high steer to 91016? first customer discount? JK

2 arms drilled and reamed 3 plcs for TRE will be $160 to your door.

[smokinthehippies]

Subscribed for payday.
What is your current eta for lead times?

[4WHEELSUPPLY]

ETA on undrilled arms will be same day! If you need em drilled for linkage it will be 1-2 days.

[774x4]

whats your paypal info?

[4WHEELSUPPLY]

paypal address is: fourwheelsupply@yahoo.com

[774x4]

payment sent..thanks!

[4WHEELSUPPLY]

Thanks for the order!

[BDX]

Payment sent.

[OrangeBronc79]

P/S arm non-drilled and cap for D/S to 22742?

Does the arm come with the stud and greese fitting?

[KillerKaveman]

oh hell yeah!! they look great! any plans for ackerman angles?

[4WHEELSUPPLY]

Originally Posted by OrangeBronc79

P/S arm non-drilled and cap for D/S to 22742?

Does the arm come with the stud and greese fitting?

Cap will be 3/4" and I can do $100 to your door.

And yes grease zirk and set screw and thick preload washer included.

[774x4]

super fast shipping, arms look great, way beefier looking in person, you should do the old picture next to a quarter shot to show the size of these! thanks!

[BDX]

Got mine yesterday, way beef! IMO Best bang for your buck! Thanks for making such a great product for a great price.

[King7765]

Need a double ended arm and a single ended arm for my rear axle
My ram is on the back of the axle.

My front axle has old poison spyder arms.
The ram is an 8inch ram, does the spacing/distance between the center line of the king pin and the center line of the hole for the TRE come into play?

These seem to have a shorter distance. Would that mean I'd be steering to sharp in the rear or I'd need a smaller ram?

Thanks for your time.

[4WHEELSUPPLY]

Originally Posted by King7765

Need a double ended arm and a single ended arm for my rear axle
My ram is on the back of the axle.

My front axle has old poison spyder arms.
The ram is an 8inch ram, does the spacing/distance between the center line of the king pin and the center line of the hole for the TRE come into play?

These seem to have a shorter distance. Would that mean I'd be steering to sharp in the rear or I'd need a smaller ram?

Thanks for your time.

Double arms are in the works. Matls are ordered. should be late next week on them. As far as the distance goes. I can go out as far as7.5" from kingpin center to center of TRE hole. I think this is pretty common.

[King7765]

Okay cool, Thanks. I will measure my current setup and report back.

[King7765]

7.5inches is what my current arms are. I'll just have to wait for the doubles to be built. Thanks!

[4WHEELSUPPLY]

Sounds good! I will get them out as soon as materials get here.

Questions. Most people running a double arm on pass or driver side?

I guess it really depends on the application, but would be nice to know which is more popular.

[King7765]

I'm going to mount mine on the drivers side knuckle. BUT this is a rear steer. On my front axle, the ram is on the passenger side because the pumpkin is on the driverside.

So unfortunately for me, the common side would be the passenger side.

So please make at least one for the driverside! LOL

[4WHEELSUPPLY]

Matls are here. Hopefully get these thrown on the mill in the next few days. Thanks

[Newoldscotts4x4]

Chevy 60 both arms drilled for TRE w/crossover and high steer shipped to 21157, thanks

[4WHEELSUPPLY]

Originally Posted by Newoldscotts4x4

Chevy 60 both arms drilled for TRE w/crossover and high steer shipped to 21157, thanks

$160 t your door. 1 day turnaround

[allornothin]

bought your caps a while back and i really just need a passenger high steer arm.....i need to get a little more turning radius out of it tho so that would be drilling the hole a little less than where stock would be correct?