Dana 60 High Steer Studs! The real deal! - Pirate4x4.Com : 4x4 and Off-Road Forum

Reid Racing · 05-26-2004, 12:11 PM

Well you asked for them, here they are.

* Fine threads on both ends
* Custom made for Dedenbear by ARP
* 220,000 psi tensile strength(stock is 180,000)
* Fits all Dana 60 high steer arms

D60112-----Single stud--------$9.00 each
D60116K----4-stud kit---------$29.00($7.25 per stud)
D60117K----5-stud kit---------$35.00($7.00 per stud)

These are available now!

Check out the drawing for the specs

HeyBeerMan · 05-26-2004, 03:23 PM

Do they have the thicker "shoulder" in the non threaded area, like GM units?

beerman

Reid Racing · 05-27-2004, 08:32 AM

Quote:

Originally Posted by HeyBeerMan

Do they have the thicker "shoulder" in the non threaded area, like GM units?

beerman

No, these are .500, we found that most of the aftermarket arms are made to .500 rather than .527(or close to it)
If you are running tapered nuts or washers the studs will be centered in the holes and will not touch the walls of the arm, whether the holes in the arms are .501 or .550

rock-rod · 05-27-2004, 11:10 AM

I just bought two sets from you for my highsteer arms, and the studs I received are fine thread on one end and coarse thread on the other. Is it possible to swap them out? I was surprised to see this when I received them, I figured they would be fine thread on both ends due to the large forces placed on them from the steering arms.

Thanks

Reid Racing · 05-27-2004, 12:26 PM

Quote:

Originally Posted by rock-rod

I just bought two sets from you for my highsteer arms, and the studs I received are fine thread on one end and coarse thread on the other. Is it possible to swap them out? I was surprised to see this when I received them, I figured they would be fine thread on both ends due to the large forces placed on them from the steering arms.

Thanks

Give me a call, I think we can do this. We are still offering the other studs like you have until we are out of stock. The new ones are priced the same but do not include nuts or washers.

Ryan

YeeP · 03-10-2005, 06:25 AM

How about nuts? After reading Billavistas High steer article I have been having trouble finding the right kind of nuts. I ordered them from GM but ended up with a Crimped nut and not a tapered nut. All I know is you are not supposed to run a lug nut, Have any hardened tapered nuts?

Eric Ruhl · 03-10-2005, 07:31 AM

Quote:

Originally Posted by YeeP

How about nuts? After reading Billavistas High steer article I have been having trouble finding the right kind of nuts. I ordered them from GM but ended up with a Crimped nut and not a tapered nut. All I know is you are not supposed to run a lug nut, Have any hardened tapered nuts?

Their web page shows nuts and washers included in the "kit".

Ryan, just a suggestion, deleting your previous bumps would clean this up a bit

Reid Racing · 07-27-2005, 10:54 AM

Top

HeyBeerMan · 08-04-2005, 01:36 PM

Quote:

Originally Posted by Dedenbear

Top

Your yellow star burned out

RealJeepMan · 08-04-2005, 06:32 PM

Quote:

Originally Posted by HeyBeerMan

Your yellow star burned out

Yeah we had just noticed that, the check is in the mail to get it back up.

Reid Racing · 08-15-2005, 04:40 PM

Yellow star is back!

05-26-2004, 12:11 PM	#1 (permalink)
Reid Racing Wheeler Join Date: Jun 2003 Member # 20872 Location: Pleasant Hill, CA Posts: 397	Dana 60 High Steer Studs! The real deal! Well you asked for them, here they are. * Fine threads on both ends * Custom made for Dedenbear by ARP * 220,000 psi tensile strength(stock is 180,000) * Fits all Dana 60 high steer arms D60112-----Single stud--------$9.00 each D60116K----4-stud kit---------$29.00($7.25 per stud) D60117K----5-stud kit---------$35.00($7.00 per stud) These are available now! Check out the drawing for the specs Attached Images __________________ Join the fight to keep public lands open to the public! Manufacturers of Dana 60, 44, 30, 10-Bolt & JK knuckles and Turbo400 & Powerglide transmission cases. (925) 935-3025 M-F 8-6pm PST race.mail@reidracing.biz http://www.reidracing.biz Built by racers for racers! Made in the USA!

05-27-2004, 11:10 AM	#4 (permalink)
rock-rod Registered User Join Date: Jun 2003 Member # 20092 Location: Porker, CO Posts: 3,466	I just bought two sets from you for my highsteer arms, and the studs I received are fine thread on one end and coarse thread on the other. Is it possible to swap them out? I was surprised to see this when I received them, I figured they would be fine thread on both ends due to the large forces placed on them from the steering arms. Thanks __________________ '94 Toyota Land Cruiser FJZ80 - Vortec L33 5.3l, 4L60e, elocked, 3" OME lift, 315 KM2s, Warn 8074.

07-27-2005, 10:54 AM	#8 (permalink)
Reid Racing Wheeler Join Date: Jun 2003 Member # 20872 Location: Pleasant Hill, CA Posts: 397	Top __________________ Join the fight to keep public lands open to the public! Manufacturers of Dana 60, 44, 30, 10-Bolt & JK knuckles and Turbo400 & Powerglide transmission cases. (925) 935-3025 M-F 8-6pm PST race.mail@reidracing.biz http://www.reidracing.biz Built by racers for racers! Made in the USA!

08-15-2005, 04:40 PM	#11 (permalink)
Reid Racing Wheeler Join Date: Jun 2003 Member # 20872 Location: Pleasant Hill, CA Posts: 397	Yellow star is back! __________________ Join the fight to keep public lands open to the public! Manufacturers of Dana 60, 44, 30, 10-Bolt & JK knuckles and Turbo400 & Powerglide transmission cases. (925) 935-3025 M-F 8-6pm PST race.mail@reidracing.biz http://www.reidracing.biz Built by racers for racers! Made in the USA!

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

05-26-2004, 03:23 PM	#2 (permalink)
HeyBeerMan Rock God Join Date: May 2001 Member # 4830 Location: Wickenburg Posts: 2,044	Do they have the thicker "shoulder" in the non threaded area, like GM units? beerman

03-10-2005, 06:25 AM	#6 (permalink)
YeeP Registered User Join Date: May 2001 Member # 4568 Location: Parker, CO Posts: 1,059	How about nuts? After reading Billavistas High steer article I have been having trouble finding the right kind of nuts. I ordered them from GM but ended up with a Crimped nut and not a tapered nut. All I know is you are not supposed to run a lug nut, Have any hardened tapered nuts?