Custom built Ford 400 engine - Pirate4x4.Com : 4x4 and Off-Road Forum

Idaho77Highboy · 10-31-2011, 03:03 PM

I have a Ford 400 engine custom built by Pat Bratton of Moffitt and Bratton Racing Engines of Boise, Idaho. The block is a truck block with reinforced main webs. The engine has been bored .030" over and stroked with a 4.250" stroked crankshaft making it 434 cu in. The engine has been blueprinted and balanced with all of the documentation. I have over $13,000 invested in it and now I need to sell it. SERIOUS INQUIRES ONLY!! I am asking $5,000 obo. This is what the engine has:

Ford 400 truck block with reinforced main webs bored .030" over.
4.250" stroked crankshaft from Tim Meyer INC.
4- bolt main caps
Custom Kevco Racing oil pan for the over sized crankshaft
Keith Black Piston - 10.3:1 CR
6.657 inch rods
new timing chain
CHI 2V aluminum heads 62.6 CC custom built with Ferrera valves
Comp Cams custom ground roller cam
Comp Cams roller rockers
MSD Pro billet distributor
Weiand 8010 intake manifold
Weiand water pump
New polished aluminum high clearance valve covers
New Holley Truck Avenger carburetor 770 CFM
Block heater

The engine is estimated to put out 450 hp and 560 ft lbs torque. This is a unique motor that would be great in a truck/ offroad vehicle or even an old hot rod. It is ready to put into a vehicle or taken to the dyno.

Pictures can be seen on my craigslist ad or I can email them.

http://boise.craigslist.org/pts/2676470026.html

Racing junk ad:

http://www.racingjunk.com/Engines-Co...00-engine.html

Idaho77Highboy · 11-02-2011, 06:02 PM

bump

Idaho77Highboy · 11-06-2011, 01:25 PM

bump....any offers?

Idaho77Highboy · 11-07-2011, 06:42 PM

Bump

10-31-2011, 03:03 PM	#1 (permalink)
Idaho77Highboy Registered User Join Date: Jan 2006 Member # 66413 Posts: 17	Custom built Ford 400 engine I have a Ford 400 engine custom built by Pat Bratton of Moffitt and Bratton Racing Engines of Boise, Idaho. The block is a truck block with reinforced main webs. The engine has been bored .030" over and stroked with a 4.250" stroked crankshaft making it 434 cu in. The engine has been blueprinted and balanced with all of the documentation. I have over $13,000 invested in it and now I need to sell it. SERIOUS INQUIRES ONLY!! I am asking $5,000 obo. This is what the engine has: Ford 400 truck block with reinforced main webs bored .030" over. 4.250" stroked crankshaft from Tim Meyer INC. 4- bolt main caps Custom Kevco Racing oil pan for the over sized crankshaft Keith Black Piston - 10.3:1 CR 6.657 inch rods new timing chain CHI 2V aluminum heads 62.6 CC custom built with Ferrera valves Comp Cams custom ground roller cam Comp Cams roller rockers MSD Pro billet distributor Weiand 8010 intake manifold Weiand water pump New polished aluminum high clearance valve covers New Holley Truck Avenger carburetor 770 CFM Block heater The engine is estimated to put out 450 hp and 560 ft lbs torque. This is a unique motor that would be great in a truck/ offroad vehicle or even an old hot rod. It is ready to put into a vehicle or taken to the dyno. Pictures can be seen on my craigslist ad or I can email them. http://boise.craigslist.org/pts/2676470026.html Racing junk ad: http://www.racingjunk.com/Engines-Co...00-engine.html Last edited by Idaho77Highboy; 11-02-2011 at 06:01 PM.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

11-02-2011, 06:02 PM	#2 (permalink)
Idaho77Highboy Registered User Join Date: Jan 2006 Member # 66413 Posts: 17	bump

11-06-2011, 01:25 PM	#3 (permalink)
Idaho77Highboy Registered User Join Date: Jan 2006 Member # 66413 Posts: 17	bump....any offers?

11-07-2011, 06:42 PM	#4 (permalink)
Idaho77Highboy Registered User Join Date: Jan 2006 Member # 66413 Posts: 17	Bump